• 전자공학회논문지
• /
• 제52권8호
• /
• pp.126-131
• /
• 2015

유도전동기의 고성능 속도 제어를 위해서는 전동기 정수의 정확한 측정이 필요하다. 특히 전동기의 토크 제어를 위해 사용되는 벡터 제어의 경우 회전자 저항과 인덕턴스의 항으로 주어지는 시정수는 제어기의 성능에 큰 영향을 준다. 또한 고정자 저항과 누설 인덕턴스는 전류제어기와 속도 제어기의 이득을 구하고 설계하는 중요한 변수가 된다. 본 논문에서는 기존의 정수 측정 방법을 수정 보완한 새로운 유도 전동기 정수 측정방법을 제시한다.

• 한국전기전자재료학회논문지
• /
• 제18권2호
• /
• pp.153-158
• /
• 2005

Recently, as the feasibility study shows that trans-Korea railway and trans-continental railway are advantageous, interest in high-speed railway system is increasing. Because railway vehicle is environment-friendly and safe compared with airplane and ship, its market-sharing increases gradually. KHST(Korean High Speed Train) has been developed by KRRI (Korea Railroad Research Institute) for last 6 years to satisfy the need. An electric railway system is composed of high-tech subsystems, among which main electric equipment such as transformers and converter are critical components determining the performance of rolling stock. We developed a measurement system for on-line test and evaluation of performances of KHST. The measurement system is composed of software part and hardware part. Perfect interface between multi-users is possible. A now method to measure temperature was applied to the measurement system. By using the system, fault diagnosis and performance evaluation of electric equipment in Korean High Speed Train was conducted during test running.

• Journal of Biosystems Engineering
• /
• 제19권4호
• /
• pp.301-310
• /
• 1994

The feasibility of using ultrasonic-wave doppler sensors for a measurement of the actual ground speed of agricultural machines was investigated. The actual ground speed is estimated from the doppler shift frequencies of the two ultrasonic-waves transmitted to and received from a moving object. A prototype of the speed-measurement system was designed and constructed for the performance test. The measurement system showed a good performance with a flat surface at speeds lower than 3m/s. However, it was failed to receive the reflected signals from the rough and irregular soil surfaces. Further researches to solve this problem and to improve its performance are now underway.

• 한국전기전자재료학회논문지
• /
• 제16권12S호
• /
• pp.1210-1216
• /
• 2003

Recently, as the road capacity reaches the limit and environmental problems becomes serious, there is gradually increased a need for railroad vehicles that are environment-friendly and have time regularity, reliability, and safety. Accordingly, in addition to conventional railroad vehicles, lots of vehicles are being newly developed. We developed the hardware and software of the measurement system for on-line test and evaluation of korean high speed train. The software controls the hardware of the measurement system and acts as interface between users and the system hardware. In this paper, practical experiment are performed to verify mechanical performance of motor and main transformer for Korean high speed rail. The experimental test carried out by using new temperature measurement method and verify the temperature performance of motor and transformer is verified.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.900-904
• /
• 2009

The measurement of contact wire uplift in electric railway is one of the most test method to accept the maximum permitted speed of new vehicles or pantographs. The contact wire uplift can be measured for shot periods when pantograph is running in monitoring station. This paper describes the development of two different methods for contact uplift measurement using vision-based system and wireless online monitoring system. Our vision-based system employs a high-speed CMOS (Complementary Metal Oxide Semiconductor) camera with gigabit ethernet LAN. The development of a real-time remote monitoring system that acquires data from any kind of sensor to be transmitted by wireless communication from overhead line and structure at 25 kV to a computer in catenary system. The proposed two kind of different measurement systems to evaluation for dynamic uplift of overhead contact wire shows promising on-field applications for high speed train such as Korea Tilting Train (TTX) and Korea Train eXpress (KTX).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 G
• /
• pp.2430-2432
• /
• 1998

Generally, in the best-known Pulse-type type and Frequency Modulated Continuous Wave(FM/CW)-type RF range measurement systems, the nearest measurable distance between antenna of system and targets is limited to several tens of meters. Moreover, in case of high-speed targets it is more difficult to measure the distance precisely. In this paper we design our own RF(X-band) range(up to 15 meters) measurement system usi code correlation for high- speed targets. It 0 the correlation value between transmitting receiving PN (Pseudo -Noise) codes. So we determine the distance between antenna of s and targets using this correlation value. We fabricated it using MIC techniques and experimental results show that the proposed syste fully qualified for a short range measurement syste

• Wind and Structures
• /
• 제20권5호
• /
• pp.701-718
• /
• 2015

The joint distribution of wind speed and wind direction at a bridge site is vital to the estimation of the basic wind speed, and hence to the wind-induced vibration analysis of long-span bridges. Instead of the conventional way relying on the weather stations, this study proposed an alternate approach to obtain the original records of wind speed and the corresponding directions based on field measurement supported by the Structural Health Monitoring System (SHMS). Specifically, SHMS of Sutong Cable-stayed Bridge (SCB) is utilized to study the basic wind speed with directional information. Four anemometers are installed in the SHMS of SCB: upstream and downstream of the main deck center, top of the north and south tower respectively. Using the recorded wind data from SHMS, the joint distribution of wind speed and direction is investigated based on statistical methods, and then the basic wind speeds in 10-year and 100-year recurrence intervals at these four key positions are calculated. Analytical results verify the reliability of the recorded wind data from SHMS, and indicate that the joint probability model for the extreme wind speed at SCB site fits well with the Weibull model. It is shown that the calculated basic wind speed is reduced by considering the influence of wind direction. Compared to the design basic wind speed in the Specification of China, basic wind speed considering the influence of direction or not is much smaller, indicating a high safety coefficient in the design of SCB. The results obtained in this study can provide not only references for further wind-resistance research of SCB, but also improve the understanding of the safety coefficient for wind-resistance design of other engineering structures in the similar area.

• Journal of Mechanical Science and Technology
• /
• 제20권4호
• /
• pp.482-493
• /
• 2006

The carbody structure of a high speed train passing through a tunnel is subjected to pressure fluctuation. Fatigue strength of the carbody structure against the fluctuating pressure loading should be proved in the design stage for safety. In this study, to get the useful information on the pressure fluctuation in the tunnel, measurement has been conducted during test running of KHST on the high speed line for two years. The measured results were analyzed and arranged to be used for carbody design. A prediction method for the magnitude and frequency of pressure change was proposed and the propagating characteristics of pressure wave was investigated. By statistical analysis for the measured results, a pressure loading spectrum for the high speed train was given. The proposed method can also be used to estimate the pressure loading spectrum for new high speed line at design stage combined with the results of train performance simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.203-206
• /
• 1997

DC servo motors are widely used in many industrial fields as actuator of robot and driving power motors of electrical vehicle. Usually in the speed control systems, of motors, speed sensors are required and this fact results in the increased price and operating cost and the limited application of the motors. In this paper, a new speed control method for DC servo motor is proposed. In the scheme, the rotational speed is estimated by the measurement values of the armature voltage and current, instead of measurement by sensor. Optimal control theory is applied to design of the controller in construction of real system. This paper also report on the results of experiments to prove the validity of the proposed method.

• Journal of Biosystems Engineering
• /
• 제35권2호
• /
• pp.85-90
• /
• 2010

This study was carried out to develop turning radius measuring method and device of using a DGPS speed sensor for agricultural tractors. The measurement system consisted of a DGPS speed sensor, a data acquisition device, a touch panel, a photo sensor, a radio modem and a notebook computer. Three methods were developed: average of turning speed-time method, integral of turning speed-time method, and speed-heading angular velocity method. Best method was average of turning speed-time method which could be used with a maximum error 2.7 cm.