• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.2
• /
• pp.193-204
• /
• 1999

Performance of a variable-speed, roller-type vane compressor was evaluated at low evaporating temperature. First, an experimental investigation was conducted to examine the performance variation as functions of both outdoor temperature and rotating speed. For this purpose, a typical heat pump was implemented as a test apparatus to measure mass flow rate and power input. Secondly, computational investigations corresponding to the heat pump test conditions were performed to predict compressor performance using ORNL Map-Based compressor model. Results obtained from the heat-pump experiments showed that both mass flow rate and power consumption were sensitively dependent on both evaporating temperature and compressor speed as was predicted from the computational results. From the comparisons of both experimental and computational results, it was well recognized that the ORNL model was subjected to larger error in the accuracy of prediction as outdoor temperature decreased. When the outdoor temperature was above $-5^{\cire}C$, errors of predicted values corresponding to both mass flow rate and power consumption were estimated as $\pm$10% and $\pm$ 15%, respectively. Finally, it is suggested that the ORNL model needs to be re-evaluated if compressor map data tested below $-5^{\cire}C$(in evaporating temperature) are available.

• Wind and Structures
• /
• v.33 no.6
• /
• pp.423-435
• /
• 2021

Although existing algorithms can predict wind speed using historical observation data, for engineering feasibility, most use moment methods and probability density functions to estimate fitted parameters. However, extreme wind speed prediction accuracy for long-term return periods is not always dependent on how the optimized frequency distribution curves are obtained; long-term return periods emphasize general distribution effects rather than marginal distributions, which are closely related to potential extreme values. Moreover, there are different wind speed parent sample types; how to theoretically select the proper extreme value distribution is uncertain. The influence of different sampling time intervals has not been evaluated in the fitting process. To overcome these shortcomings, updated steps are introduced, involving parameter sensitivity analysis for different sampling time intervals. The extreme value prediction accuracy of unknown parent samples is also discussed. Probability analysis of mean wind is combined with estimation of the probability plot correlation coefficient and the maximum likelihood method; an iterative estimation algorithm is proposed. With the updated steps and comparison using a Monte Carlo simulation, a fitting policy suitable for different parent distributions is proposed; its feasibility is demonstrated in extreme wind speed evaluations at Longhua and Chuansha meteorological stations in Shanghai, China.

• Journal of Wind Energy
• /
• v.10 no.4
• /
• pp.20-27
• /
• 2019

High-speed shaft coupling in a wind power system transmits power and absorbs variations in length and spindle dislocation between the gearbox and generator. Furthermore, the coupling has an insulation function that prevents electrical corrosion caused by the flow of the generator's current into the gearbox and prevents overload resulting from sudden power failure from being transferred to the gearbox. Its design, functions, and part verification are described in the IEC61400 and GL Guidelines, which specify that the part must have a durability life of 20 years or longer under distance variation and axial misalignment between the gearbox and the generator. This study presents the design of a high-speed coupling through composite stiffness calculation, structural analysis, and comparative analysis of test and theory to identify the characteristics of high-speed coupling for a large-capacity 6 MW wind power generator. A prototype was fabricated by optimizing the manufacturing process for each part based on the design, and the reliability of the fabricated prototype was verified by evaluating the performance of the target quantitative evaluation items.

• Journal of the Institute of Convergence Signal Processing
• /
• v.6 no.2
• /
• pp.82-88
• /
• 2005

A compensation scheme for a class of linearly parameterized systems is presented. The compensator consists of a typical linearizing control and an adaptive observer with integration type update law, which is based on Speed Gradient (SG) algorithm.. Instead of the intermediate functions of the compensation schemes suggested by other researchers, the proposed compensator is designed with some design functions which guarantee the growth, convexity, attainability, and pseudo gradient conditions in the update law. The scheme achieves the asymptotic stability of the tracking error and the boundedness of the estimation errors. A numerical example is given to demonstrate the validity of the proposed design.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.114-119
• /
• 2008

A refined three-dimensional finite element interaction model between the high-speed train and railway bride deck has been developed in the present study. Analytical predictions of vertical deflections for a railway bridge are compared with in-situ test results and a good agreement is achieved. Then, input variables employed in the analytical comparisons are selected as random variables for the limit state functions. followed by risk assessment. For this purpose, a linear adaptive weighted response surface method has been developed and applied. A typical railway bridge has been selected and the limit state functions are employed from UIC and Korean specifications in the comparative studies. The results reveal that Korean specifications give significantly risky reliability indices in comparison with UIC specifications. It is thus encouraged from the above that the present linear adaptive weighted response surface method can be an alternative for the fast estimation of nonlinear structural systems.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.4
• /
• pp.313-323
• /
• 2017

As vehicles become more intelligent this is focused on ways to enhance safety and convenience for both drivers and passengers. In particular, x-by-wire systems that replace rigid mechanical components with dynamically configurable electronic elements are being developed to expand intelligent functions, such as adaptive cruise control or lane departure warning system. Because the malfunction of safety-related modules controlling critical functions, such as brakes, throttle, and steering in x-by-wire systems, can cause injury or death, safety and reliability are the most critical issue for automotive vendors and parts manufacturers. In an effort to develop better and effective brake-by-wire system, this paper presents EMB system by using the low speed electric vehicle, which is not required large braking force, with motor controller. In addition, we design performance evaluation system of EMB with 1/4 low speed electric vehicle model and suggested EMB is evaluated through the performance evaluation system.

• Journal of Welding and Joining
• /
• v.27 no.5
• /
• pp.81-87
• /
• 2009

Recently, extruded aluminium-alloy panels have been used in the car bodies for the purpose of the light-weight of railway vehicles and FSW(Friction Stir Welding), which is superior to the arc weldings, has been applied in the railway vehicles. This paper presents the optimum design of the FSW process on A6005 extruded alloy for railway vehicles to improve its mechanical properties. Rotational speed, welding speed and tilting angle of the tool tip were chosen as design parameters. Three objective functions were determined; maximizing the tensile strength, minimizing the hardness and maximizing the difference between the normalized tensile strength and hardness. The tensile tests and the hardness tests for fifteen FSW experiments were carried out according to the central composite design table. Recursive model functions on three characteristic values, such as the tensile strength, the hardness difference(${\Delta}Hv$) and the difference of normalized tensile strength and ${\Delta}Hv$, were estimated according to the classical response surface analysis methodology. The reliability of each recursive function was verified by F-test using the analysis of variance table. Sensitivity analysis on each characteristic value was done. Finally, the optimum values of three design parameters were found using Sequential Quadratic Programming algorithm.

• Korean Journal of Crystallography
• /
• v.12 no.2
• /
• pp.102-112
• /
• 2001

The mechanical properties of silicon crystals are important from the viewpoint of wafer and device fabrication processes. It is now widely recognized that silicon undergoes a series of phase transformations when subjected to high pressures, using conventional high pressure devices, such as diamond anvils or indenters. Diamond tip scratching on a silicon surface in the various conditions introduces various kinds of mechanical damage and stressed states. Micro Raman spectroscopy was used to observe the phase transition of single crystal silicon. As results, different morphologies were observed as functions of scratching speed and loading condition and various phases were observed as functions of scratching speed and loading condition.

• International Journal of CAD/CAM
• /
• v.6 no.1
• /
• pp.59-64
• /
• 2006

A new method to obtain explicit re-parameterization that preserves the curve degree and parametric domain is presented in this paper. The re-parameterization brings a curve very close to the arc length parameterization under $L_2$ norm but with less segmentation. The re-parameterization functions we used are $C^1$ continuous piecewise rational linear functions, which provide more flexibility and can be easily identified by solving a quadratic equation. Based on the outstanding performance of Mobius transformation on modifying pieces with monotonic parametric speed, we first create a partition of the original curve, in which the parametric speed of each segment is of monotonic variation. The values of new parameters corresponding to the subdivision points are specified a priori as the ratio of its cumulative arc length and its total arc length. $C^1$ continuity conditions are imposed to each segment, thus, with respect to the new parameters, the objective function is linear and admits a closed-form optimization. Illustrative examples are also given to assess the performance of our new method.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.9
• /
• pp.2388-2404
• /
• 2012

Cryptographic hash functions are widely used in many information security applications like digital signatures, message authentication codes (MACs), and other forms of authentication. In response to recent advances in cryptanalysis of commonly used hash algorithms, National Institute of Standards and Technology (NIST) announced a publicly open competition for selection of new standard Secure Hash Algorithm called SHA-3. One important aspect of this competition is evaluation of hardware performances of the candidates. In this work we present efficient hardware implementations of SHA-3 finalists: JH, Keccak and Skein. We propose high speed architectures using Look-Up Table (LUT) resources on FPGAs, to minimize chip area and to reduce critical path lengths. This approach allows us to design data paths of SHA-3 finalists with minimum resources and higher clock frequencies. We implemented and investigated the performance of these candidates on modern and latest FPGA devices from Xilinx. This work serves as performance investigation of leading SHA-3 finalists on most up-to-date FPGAs.