• 한국건축시공학회지
• /
• 제3권1호
• /
• pp.139-146
• /
• 2003

The special requirements of high-performance concrete(HPC) could be enhanced property over others such as compressive strength, durability, and construction practices. In order to satisfy these requirements a series of laboratory trial mixes and following mock-up test of reinforced concrete wall at field were performed in this study. The objective of this study was to quantitatively evaluate the workability, compressive strength, and the increased heat of hydration caused by the increase of the specific weight of cement according to various variables. Six example series designed about a minimum compressive strength of 500kgf/$\textrm{cm}^2$ at 28 days, and an approximately slump and slump flow of 25cm and 60cm respectively were tested. The selection process of the specific weight of water and the percentage of fly-ash transposition determined to be most suitable for the production of HPC is presented in the following paper.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.621-626
• /
• 2010

According to development of method and device of Finite Element Analysis, the strength of welded joint is demonstrated by Finite Element Analysis not classical calculations. On the FEA, all of the joints for carbody are assumed to be ideal connections and the yield stress of welded joint is assumed to be the same to base metal. On these assumption, FEA is appropriate to evaluate the overall stability and strength of whole carbody. The classical calculation is appropriate to evaluate strength of specific welded joint and to determine the weld method and properties. Some project request strength calculation of the specific welded joints in addition to FEA, because of the demonstration of stability. The objective of this paper is the check of the consistency of the FEA result for the welded joints by the stress comparison between Detailed FE Model and classical calculation and the evaluation of the reliability of FEA result.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.529-532
• /
• 2004

As the purpose of this study is a research of series to obtain fundamental data on the development of the product of foamed concrete using bottom ash for various applications in the field, the main purpose is the light weight of product of concrete. In this experiment, method of mixing of foam is very important because it control specific gravity and strength of the product. As the test results, it was found that regardless of mixing method the grower the concentration of foaming agent the lower the specific gravity and the compressive strength of the specimen especially pre-foaming method. From a strength point of view, we knew that mix-foaming method and steam curing is efficient to obtain a adequate compressive strength of foamed concrete.

• Journal of the Korean Wood Science and Technology
• /
• 제13권3호
• /
• pp.3-26
• /
• 1985

The object of this study was to investigate the effects on physical and mechanical properties of wood particle and sawdust board combined with wire net. Conventional forming, press-lam, and veneer comply boards combining one to four wire net sheets were made from wood particle and sawdust with different spacings (8, 10, 12, and 18 Mok) and different wire diameters (0.35, 0.50, and 0.80mm) composing wire net. They were compared and analyzed statistically with specific gravity, thickness swelling, length swelling, bending properties (modulus of rupture, modulus of elasticity, work to proportional limit, and total work), internal bonding strength, and screw holding strength between wood particle and sawdust boards. The results obtained at this study as cording to the discussions might be concluded as follows; 1. In specific gravity, both particle and sawdust boards by press-lam method were higher than by conventional forming and veneer comply method, and the boards containing more wire net sheets also showed higher value. But the wire net spacings(Mok) had no influence on specific gravity. In general, particle board showed higher specific gravity than sawdust board. Veneer comply board showed lowest specific gravity values. 2. Both particle and sawdust boards by press-lam method was slightly lower than by conventional forming and veneer comply method in thickness swelling. The sawdust board containing 8, 12. and 18 Mok wire net showed lower thickness swelling than the corresponding particle board, but both sawdust and particle boards containing the T8 and 10 Mok wire net showed higher and similar thickness swelling. 3. Both particle and sawdust boards containing wire net showed no difference in MOR and MOE of bending. Comply board was the highest and particle board showed slightly higher than sawdust board in MOR and MOE values. 4. In work to proportional limit and total work in bending, both particle and sawdust boards containing thicker wire diameter and more wire net sheets showed higher value. From these facts, it is conceivable that boards with thicker wire diameter and more wire net sheets show increasing resistance against external force. But there was no significant difference between particle and sawdust borads. 5. In resistance against delamination (internal bonding strength), both sawdust and particle boards containing wire net showed lower value than control, and also showed decreasing tendency with more number of wire net sheet composed. Particle board showed higher resistance against delamination than sawdust board. 6. In screw holding strength, sawdust board containing thicker wire diameter and more wire net sheets showed higher value, but particle board by press-lam method was higher than by conventional forming and veneer comply method. Screw holding strength of particle board was higher than that of sawdust board.

• 한국공작기계학회논문집
• /
• 제10권3호
• /
• pp.90-96
• /
• 2001

Experimental investigations were carried out to find the characteristics of grinding of ceramics. Grinding mechanisms of ceramics were inspected through the microscopic examination. It has been found that the specific grinding energy of ceramics is relatively low as compared to that of steels. The specific grinding energy affects the surface roughness and the residual stress of ground surface. the experimental results indicate that the rougher surface finish and higher compressive residual stress are obtained at lower specific grinding energy. The surface roughness and the residual stress of the ground surface have significant effects on the strength of ground piece of ceramics.

• Journal of Biosystems Engineering
• /
• 제31권1호
• /
• pp.24-32
• /
• 2006

Compaction is becoming a greater concern in crop production and the environment because it can have deleterious effects on growing conditions that are difficult to remediate. Because compaction can vary considerably from point to point within a field, and also from depth to depth within the soil profile, it is important to consider quantification and management of the spatial and vertical variability in soil compaction when developing an overall site-specific crop management plan. In this paper, the importance of soil compaction, techniques for quantification of its variability, and the concept of site-specific tillage are examined. Methods and systems to detect within-field variation in soil strength as a surrogate measure of soil compaction and related soil properties are also compared and discussed. Quantification of variability in soil compaction and site-specific compaction management was motivated recently, and sensors and control systems are still under development. Future study will need to address a number of issues related to understanding and applying the sensor measurements.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.337-342
• /
• 2000

Experimental investigations were carried out to find the characteristics of grinding of ceramics. Grinding mechanisms of ceramics were inspected through the microscopic examination. It has been found that the specific grinding energy of ceramics is relatively low as compared to that of steels. The specific grinding energy affects the surface roughness and the residual stress of ground surface. The experimental results indicate that the rougher surface finish and higher compressive residual stress are obtained at lower specific grinding energy. The surface roughness and the residual stress of the ground surface have significant effects on the strength of ground piece of ceramics.

• Design & Manufacturing
• /
• 제10권2호
• /
• pp.12-17
• /
• 2016

Recently, lightweight material is attracting attention as a solution to the problem of fuel efficiency and increasing the need for development. CFRP has been attracting attention as lightweight materials for automobile because it has a high specific stiffness and specific strength compared to steel material. CFRP have a wide range of mechanical properties depending on the laminate condition. In this paper, study on the forming analysis of double-dome model was performed considering CFRP prepreg laminate condition and coefficient of friction. After forming analysis, the result has compared with wrinkling area and vertical strain of fiber to the laminated condition. And then compared with inflow of blank to the laminate condition. Through this paper, we propose the forming analysis methods of CFRP material.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.81-84
• /
• 1999

In this study, the influence of specific surface area of cement, substitution ratio of gypsum anhydrite on the physical properties of concrete were investigated by measurements of slump, air content and compressive strength. The results showed that reducing the specific surface area of cement under 3200$\textrm{cm}^2$/g and using 20% of gypsum anhydrite were desirable to prevent the decrease in workability and strength of concrete in summer season.

• 동력기계공학회지
• /
• 제20권6호
• /
• pp.46-50
• /
• 2016

This study was carried out to investigate the effect of cold working on the tensile strength of Fe-26Mn-4Co-2Al damping alloy. ${\alpha}^{\prime}$ and ${\varepsilon}$-martensite were formed by cold working, and martensite was formed with the specific direction and surface relief. With the increasing degree of cold rolling, volume fraction of ${\alpha}^{\prime}$-martensite was increased, whereas the volume fraction of ${\varepsilon}$-martensite was decreased after rising to maximum value at specific lever of cold rolling. Tensile strength was linearly increased with an increasing of degree of cold rolling. Tensile strength was strongly affected to the volume fraction of ${\varepsilon}$-martensite formed by cold working, but the effect of volume fraction of ${\varepsilon}$-martensite on the tensile strength was not observed.