• Steel and Composite Structures
• /
• 제19권3호
• /
• pp.585-599
• /
• 2015

This paper presents the experimental work on fatigue life and specific fatigue strength of circular hollow sectioned steel tube and wood filled circular hollow section steel tube. Burning effect was observed in the case of circular hollow sectioned steel tube when it is subjected to Maximum bending moment of 19613.30 N-mm at 4200 rpm, but this did not happen in the case of wood filled hollow section. Statistical analysis was done based on the experimental data and relations have been built to predict the number of cycles for the applied stress or vice versa. The relations built in this paper can safely be applied for design of the fatigue life or fatigue strength of circular hollow sections and wood filled hollow sections. Results were validated by static specific bending strengths determined by ANSYS using a known applied load.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.160-167
• /
• 2000

In this research, the fatigue behaviors of carbonitrided Cr-Mo(SCM415) steel are examined. From fatigue test results, we propose a modified fatigue strength evaluation model and modified formulae. That is, we develop improved models fur evaluating and predicting the fatigue strength of carbonitrided SCM415 by modifying specific terms in the Murakami and Endo's model which is the representative fatigue strength evaluation formulae fur high strength steel.

• 대한기계학회논문집
• /
• 제17권10호
• /
• pp.2475-2482
• /
• 1993

The effects of the hole size(2R) and the specimen width(W) on the fatigue strength and the fatigue life in plain woven glass/epoxy composite plates are experimentally investigated under constant amplitude tensile fatigue loading. It is shown in this study that the notch sensitivity under fatigue loading is lower than that under static loading. It can be explained by the fact that the stress concentration is relaxed by the damage developed at the boundary of circular hole. To predict the fatigue strength at a specific cycle, the modified point stress criterion represented as a function of the geometry of the specimen(2R and W) is applied. It is found that the model used in the prediction of the notched tensile strength predicts the fatigue strength with reasonable accuracy. A model for predicting the fatigue life in the notched specimen, based on the S-$N_f$, curve in the smooth specimen, is suggested.

• 한국해양공학회지
• /
• 제6권1호
• /
• pp.113-121
• /
• 1992

In this study, the variation of fatigue strength in CF/PEEK and CF/EPOXY, the matrix and interfacial strength of which differ from each other, has been studied from the viewpoint of microfracture behavior. The results obtained are as follows; According as the fatigue strength moves from the lower cycle range to the higher cycle range, that of CF/PEEK shows higher curve than that of CF/EPOXY does. In the early stage of fatigue life, the characteristic of fatigue crack in CF/PEEK is mainly the fracture of longitudinal fiber, while that in CF/EPOXY is the fracture of transverse fiber. The difference of fatigue strength in these materials can be explained by the fracture criteria of transverse fiber and longitudinal fiber.

• Tribology and Lubricants
• /
• 제15권2호
• /
• pp.141-149
• /
• 1999

Fracture, fatigue and wear characteristics of Al-Si alloy used for compressor are experimentally studied. Plane strain fracture toughness test is carried out using three point bending specimen. Fatigue test is performed under constant loading condition and wear test is carried out as a function of sliding velocity and applied load. To obtain the crack propagation characteristics and wear mechanism of Al-Si alloy, fracture and worn surfaces are investigated using SEM. It is verified that fracture and fatigue strength of Al-Si alloy are improved by the fine microstructure of alloy. The wear behavior and specific wear amount of Al-Si alloy are not dependent on the microstructure but on a function of the silicon content. Anodizing on the surface of Al-Si alloy, surface hardness and wear characteristics are improved.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1121-1126
• /
• 2003

Strength evaluation was carried out for the fillet and oil hole of crankshaft of medium speed diesel HiMSEN engine to verify initial concept design. Alternating torque obtained from torsional vibration analysis and radial force due to firing pressure were applied. It was assumed that the maximum alternating torque and radial force occur simultaneously. Weak points in view of fatigue are proceeding fillet and crank pin fillet area and the minimum normalized fatigue safety factor is 1.17 at crank pin fillet. The fatigue strength of the oil hole was evaluated to verify the effect of the surface roughness of the oil hole. As results, the specific level of the inner surface roughness and the polishing depth of the oil hole for sufficient fatigue strength was suggested. The maximum stress value and stress distribution at the inner surface of the oil hole can be easily estimated at initial design stage by the newly developed method.

• 한국가스학회지
• /
• 제17권6호
• /
• pp.46-51
• /
• 2013

복합재 압력용기는 높은 비강성과 비강도 그리고 내피로성으로 수소연료전지자동차와 천연가스자동차에 사용된다. 이음매가 없는 일체형 라이너를 갖는 복합재 압력용기는 고강도 탄소섬유와 에폭시 레진으로 라이너 전체를 감싼다. 본 연구에서는 구조적으로 취약한 너클 부위와 압축잔류응력을 고려하여 필라멘트 와인딩 패턴과 자긴압력 설계 기법을 제시하였다. 복합재 압력용기 시제품에 대한 압력반복시험을 통해 제안된 방법을 검증한다.

• 한국안전학회지
• /
• 제29권6호
• /
• pp.81-86
• /
• 2014

Composite materials have high specific stiffness, specific strength than existing concrete or steel materials. It has superior dynamic properties when utilizing advantages of material such as Non-corrosive, light weight, non-conducting and it has superior mold ability which can make variable shapes. Thus, in the construction, for using composite materials as construction materials, the study carried out static strength of fiber right angle direction and fatigue performance of FRP deck member. The study is going to deduct S-N curve by analyzing the results comparatively and estimate long-term durability. From now on, the study is going to provide interpretation of FRP member and basic data of design basis, furthermore providing foundation technique of composite materials' application of structural frame is the goal of this study.

• 대한기계학회논문집A
• /
• 제34권10호
• /
• pp.1411-1417
• /
• 2010

탄소섬유강화 복합재료는 높은 비강도, 비강성, 설계유연성 및 우수한 화학적 특성 등으로 인하여 여러분야에서 각광받고 있는 구조재료이다. 대부분의 CFRP 복합재료 제품들은 여러 부품들을 주로 볼트, 핀 등의 기계적인 방법으로 조립하여 제작된다. 볼트나 핀에 의해 발생하는 hole 은 구조물 내에서 노치로 작용하여 부품의 강도저하의 원인으로 작용한다. 본 논문에서는 피로하중에 의한 CFRP 복합재료 홀 노치재의 잔류강도를 실험적으로 평가하였다. 이를 위하여, 시편에 일정 반복 수만큼 피로하중을 부여하였으며, 이후 파괴시험을 통하여 홀 노치재의 잔류강도를 측정하였다. 그 결과, 피로하중으로 인해 하중방향의 균열이 발생하는 것을 확인하였으며 이 균열이 홀의 노치효과를 감소시켜 잔류강도를 증가시키는 것으로 생각되었다. 시편의 잔류강도는 일정 수준까지 증가하다가 감소하는 것으로 평가되었으며, 이를 Reifsneider 등의 평활재 잔류강도 저하모델과 Yip 등의 홀 노치재 응력재분포 함수를 이용하여, 피로하중 하의 홀 노치재 잔류강도 변화를 수식으로 나타내었다.

• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.140-146
• /
• 2003

Metal matrix composites had generated a lot of interest in recent time because of their high specific strength and stiffness in specific properties. It was also highlighted as the material of frontier industry because strength, heat-resistance, corrosion-resistance and wear-resistance were superiored. In this study, the strength properties of $Al_{18}B_{4}O_{33}$/AC4CH composites were represented mixing the binder of $SiO_2$. It was also fabricated by squeeze casting. $Al_{18}B_{4}O_{33}$/AC4CH was fabricated at the melt temperature of $760^{\circ}C$, the perform temperature of $700^{\circ}C$ and mold temperature of $200^{\circ}C$ under the pressure of 83.4MPa. Consequently, fatigue life was observed roughly in the order of AC4CH> nobiner> $SiO_2$, independently on crack propagation direction and stress ratio.