• Advances in concrete construction
• /
• 제11권5호
• /
• pp.429-445
• /
• 2021

With regard to economic efficiency, composite fix beams are widely used to pass longitudinal shear forces across the interface. The current knowledge of the composite beam load-slip activity and shear capability are restricted to data from measurements of push-off. Modelling and analysis of the composite beams based on Euro-code 4 regarding to shear, bending, and deflection under differing loads were carried out using Finite Element through an efficient computer simulation and the final loading and sections capacity based on the failure modes was analysed. In bending, the section potential was increased by an improvement of the strength in both steel and concrete, but the flexural and compressive resistance growth is very weak (3.2% 3.1% and 3.0%), while the strength of the concrete has increased respectively from 25 N/mm² to 30, 35, and 40 N/mm² compared to the increment of steel strength by 27% and 21% when it was raised from 275 to 355 and 460 N/mm², respectively. It was found that the final flexural load capacity of fix beams was declined with increase in the fix beam span for both three steel strength. The shear capacity of sections was remained unchanged at constant steel strength and different length, but raised with final yield strength increment of steel sections by 29%, and 67% when it was raised from 275 N/mm² to 355 N/mm² and 460 N/mm², respectively.

• 대한토목학회논문집
• /
• 제41권3호
• /
• pp.201-208
• /
• 2021

본 논문에서는 하부수평브레이싱 설치에 따른 무도상 철도판형교의 횡방향 및 비틀림거동에 관한 영향을 검토하였다. 우선 하부브레이싱의 부재 배치 형태가 다른 해석모델을 대상으로 하여 열차하중에 의한 횡방향변위를 비교 검토하여 가장 효율적인 하부 브레이싱의 배치에 대하여 검토하였다. 다음으로는 하부브레이싱을 설치한 2주형 철도판형교의 비틀림거동에 대해 검토를 수행하였다. 또한, FEM 해석결과로부터 구한 비틀림상수와 상부와 하부수평브레이싱을 등가두께로 치환하여 폐합단면으로 하는 철도판형교의 비틀림상수를 비교하였고, 교량의 지간길이와 하부브레이싱의 단면적의 영향을 검토하였다. 이와같은 해석결과를 기초로 본 연구에서는 횡좌굴모멘트와 비틀림상수비와의 관계곡선을 제시하였고 비틀림보강이 필요한 철도판형교의 범위를 제안하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권5호
• /
• pp.43-48
• /
• 2022

본 논문에서는 신축량이 크고 내구성이 우수한 모듈러 신축이음장치의 내진성능을 평가하기 위해 지진응답 거동해석과 지진거동모사실험을 수행하였다. 지진응답 거동해석은 한국(KS), 미국(AASHTO LRFD), 그리고 유럽(Eurocode)의 설계기준 응답스팩트럼을 적용하여 인공지진파를 생성하였다. 해석대상 교량은 경간 1,000m 사장교를 대상으로 각 기준에 대해 세가지의 인공지진파를 생성하였으며, 지진거동모사실험은 축방향과 횡방향의 동적 유압가력기를 사용하여 인공지진파를 재현하였다. 실험결과 축방향, 횡방향 및 양방향에 인공지진파를 재하하였을 때 신축이음의 거동 이상이나 파괴는 발생하지 않았으며, 신축이음장치의 지진거동에 대한 내구성 및 안전성을 확인하였다.

• Nuclear Engineering and Technology
• /
• 제54권10호
• /
• pp.3587-3594
• /
• 2022

A distributed high-speed data acquisition and monitoring system for the RF negative ion source at Huazhong University of Science and Technology (HUST) is developed, which consists of data acquisition, data forwarding and data processing. Firstly, the data acquisition modules sample physical signals at high speed and upload the sampling data with corresponding absolute-time labels over UDP, which builds the time correlation among different signals. And a special data packet format is proposed for the data upload, which is convenient for packing or parsing a fixed-length packet, especially when the span of the time labels in a packet crosses an absolute second. The data forwarding modules then receive the UDP messages and distribute their data packets to the real-time display module and the data storage modules by PUB/SUB-pattern message queue of ZeroMQ. As for the data storage, a scheme combining the file server and MySQL database is adopted to increase the storage rate and facilitate the data query. The test results show that the loss rate of the data packets is within the range of 0-5% and the storage rate is higher than 20 Mbps, both acceptable for the HUST RF negative ion source.

• The Journal of Advanced Prosthodontics
• /
• 제13권4호
• /
• pp.191-204
• /
• 2021

PURPOSE. The purpose of this study is to present a methodology to evaluate the accuracy of intraoral scanners (IOS) used in vivo. MATERIALS AND METHODS. A specific feature-based gauge was designed, manufactured, and measured in a coordinate measuring machine (CMM), obtaining reference distances and angles. Then, 10 scans were taken by an IOS with the gauge in the patient's mouth and from the obtained stereolithography (STL) files, a total of 40 distances and 150 angles were measured and compared with the gauge's reference values. In order to provide a comparison, there were defined distance and angle groups in accordance with the increasing scanning area: from a short span area to a complete-arch scanning extension. Data was analyzed using software for statistical analysis. RESULTS. Deviations in measured distances showed that accuracy worsened as the scanning area increased: trueness varied from 0.018 ± 0.021 mm in a distance equivalent to the space spanning a four-unit bridge to 0.106 ± 0.08 mm in a space equivalent to a complete arch. Precision ranged from 0.015 ± 0.03 mm to 0.077 ± 0.073 mm in the same two areas. When analyzing angles, deviations did not show such a worsening pattern. In addition, deviations in angle measurement values were low and there were no calculated significant differences among angle groups. CONCLUSION. Currently, there is no standardized procedure to assess the accuracy of IOS in vivo, and the results show that the proposed methodology can contribute to this purpose. The deviations measured in the study show a worsening accuracy when increasing the length of the scanning area.

• Wind and Structures
• /
• 제34권4호
• /
• pp.355-369
• /
• 2022

Section model test, as the most commonly used method to evaluate the aerostatic and aeroelastic performances of long-span bridges, may be carried out under different conditions of incoming wind speed, geometric scale and wind tunnel facilities, which may lead to potential Reynolds number (Re) effect, model scaling effect and wind tunnel scale effect, respectively. The Re effect and scale effect on aerostatic force coefficients and aeroelastic characteristics of streamlined bridge decks were investigated via 1:100 and 1:60 scale section model tests. The influence of auxiliary facilities was further investigated by comparative tests between a bare deck section and the deck section with auxiliary facilities. The force measurement results over a Re region from about 1×10⁵ to 4×10⁵ indicate that the drag coefficients of both deck sections show obvious Re effect, while the pitching moment coefficients have weak Re dependence. The lift coefficients of the smaller scale models have more significant Re effect. Comparative tests of different scale models under the same Re number indicate that the static force coefficients have obvious scale effect, which is even more prominent than the Re effect. Additionally, the scale effect induced by lower model length to wind tunnel height ratio may produce static force coefficients with smaller absolute values, which may be less conservative for structural design. The results with respect to flutter stability indicate that the aerodynamic-damping-related flutter derivatives 𝘈^*₂ and 𝐴^*₁𝐻^*₃ have opposite scale effect, which makes the overall scale effect on critical flutter wind speed greatly weakened. The most significant scale effect on critical flutter wind speed occurs at +3° wind angle of attack, which makes the small-scale section models give conservative predictions.

• Steel and Composite Structures
• /
• 제48권6호
• /
• pp.693-708
• /
• 2023

Composite beams, two materials joined together, have become more common in structural engineering over the past few decades because they have better mechanical and structural properties. The shear connectors between their layers exhibit some deformability with finite stiffness, resulting in interfacial shear slip, a phenomenon known as partial shear interaction. Such a partial shear interaction contributes significantly to the composite beams. To provide precise predictions of the geometric nonlinear behavior shown by two-layered composite beams with interfacial shear slips, a robust analytical model has been developed that incorporates the influence of significant displacements. The application of a higher-order beam theory to the two material layers results in a third-order adjustment of the longitudinal displacement within each layer along the depth of the beam. Deformable shear connectors are employed at the interface to represent the partial shear interaction by means of a sequence of shear connectors that are evenly distributed throughout the beam's length. The Von-Karman theory of large deflection incorporates geometric nonlinearity into the governing equations, which are then solved analytically using the Navier solution technique. Suggested model exhibits a notable level of agreement with published findings, and numerical outputs derived from finite element (FE) model. Large displacement substantially reduces deflection, interfacial shear slip, and stress values. Geometric nonlinearity has a significant impact on beams with larger span-to-depth ratio and a greater degree of shear connector deformability. Potentially, the analytical model can accurately predict the geometric nonlinear responses of composite beams. The model has a high degree of generality, which might aid in the numerical solution of composite beams with varying configurations and shear criteria.

• 대한토목학회논문집
• /
• 제30권2A호
• /
• pp.149-159
• /
• 2010

본 연구에서는 전두께 프리캐스트 바닥판을 적용한 CFT 트러스 거더 합성형교의 구조거동을 평가하기 위한 실험적 연구를 수행하였다. 모형교량의 지간장은 20 m이고, CFT 트러스 거더의 상현재와 하현재는 콘크리트 충전강관 단면이다. CFT 트러스 거더 합성형교의 구조특성을 평가하기 위해 정적 및 동적실험을 수행하였다. 실험 및 해석에 의해 산정된 고유진동수가 잘 일치함을 확인하였고, 해석결과에서 거더간에 설치되는 브레이싱은 CFT 트러스 거더 합성형교의 고유진동수에 거의 영향을 미치지 않는 것으로 나타났다. 정적 휨 실험을 통해서 CFT 트러스 거더 합성형교의 항복강도 및 변형특성을 평가하였다. 또한, 실험결과를 통해서 프리캐스트 바닥판을 통한 등분포 전단연결재의 배치는 CFT 트러스 거더의 합성형교에 적용 가능함을 확인하였다.

• 대한토목학회논문집
• /
• 제29권3A호
• /
• pp.199-207
• /
• 2009

본 논문에서는 신뢰도기반 도로교설계기준을 위한 새로운 활하중모형을 개발하였다. 합리적 하중모형과 함께 하중의 통계적 특성의 구축은 신뢰도기반 설계기준의 개발에 매우 중요하다. 이전 논문에서는 WIM 또는 BWIM시스템을 이용하여 수집된 국내 8개 지역의 자료를 분석하여 교량수명기간동안의 예상최대중량을 구하였다. 차종별 총중량의 확률분포는 상위 20%의 자료를 이용하여 극한분포(Gumbel분포)로 가정되었으며 이 확률분포를 사용하여 교량수명기간동안의 최대중량을 예측하였다. 이 논문에서는 교량상에 두 대 이상의 차량이 동시에 재하되는 경우를 분석하였다. 여러 자료를 이용하여 동시재하의 확률을 구하였으며 이에 따른 동시재하차량의 총중량을 이전 논문과 같은 확률분포를 이용하여 구하였다. 10-200 m까지의 지간별로 예측된 하중효과를 모사할 수 있는 공칭하중모형이 제안되었다. 제안된 하중모형은 기존의 하중모형 뿐만 아니라 국외의 여러 기준들과 비교분석되었다.

• 대한토목학회논문집
• /
• 제29권5A호
• /
• pp.477-486
• /
• 2009

이 논문은 정다각형 중실 변단면을 갖는 정적 최강아치에 관한 연구이다. 아치의 지간길이와 체적은 정다각형 단면깊이의 형상함수에 상관없이 항상 일정하다. 아치에 정적 연직 집중하중과 수평 집중하중이 작용하는 경우에 단면에 발생하는 최대 수직응력을 산정하였다. 산정된 최대 수직응력이 최소가 되는 정적 최강아치의 변단면 형상, 즉 일정체적 변단면 아치의 단면비를 산정하였다. 부정정 아치의 부정정력을 구하기 위하여 최소일의 원리를 이용하였다. 일련의 수치해석 예를 통하여 정적 최강아치의 단면비를 표 및 그림에 나타내었다. 이 연구의 결과는 아치구조의 최소중량 설계에 매우 유용한 자료를 제공 할 수 있다.