• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.16 no.4
• /
• pp.499-507
• /
• 1994

The aim of this experiment is to compare the healing process of extraction sockets after immediate implant placement with those using autogenous bone grafts and guided tissue regeneration with Gore-Tex. The first lower premolars and the second premolars of six experimental dogs were extracted and Stryker fin type implants were placed into the extraction sockets immediately after extraction. In the control group, any graft materials were'not used and the dead space around implants was left in itself and covered with only periosteum. In the experimental group A, implants were covered with Gore tex without any bone grafts, and in the experimental group B, the dead space around implants was filled with the bone chips gained from drilling procedure. Each experimental dogs were sacrificed at the 1st, 2nd, 3rd, 6th, and 8th week and the specimens were observed by gross examination, radiological examination, and light microscopic examination. The following results were obtained. 1. Well healed soft tissue and no mobility of the implants were observed in control and two experimental groups. 2. In the radiogical examination, radiopacity around implants had been increased gradually. 3. In the microscopic examination, there were good healing process and active new bone formation in both in the experimental groups, Especially the more amount of new bone formation occurred in the experimental group B using bone chips. 4. Bone chip grafts and guided tissue regeneration (GTR) using Gore-Tex may be one of the successful methods in the immediate implantation.

• Tunnel and Underground Space
• /
• v.5 no.4
• /
• pp.336-346
• /
• 1995

Geotechnical Information System (GTIS) for efficient management of three dimensional borehole data has been developed. Some problems were raised during the input process of borehole data, and alternative solutions were sought. According to the previous geotechnical reports, there is no unified weathering classification scheme. A criterion, 100 times/30cm from SPT, was turned out inappropriate to the discrimination of weathered rock from weathered soil. It has also been suggested that weathered soil, weathered rock, soft rock, and hard rock should be defined as CW, HW, MW, and SW~fresh condition. For better comparison of RQD, the use of NX size coring is recommended for the whole area although BX size coring has been used in excavated area. The limit of drilling depth up to 1 m from the top of surface of hard rock should be extended to avoid possible wrong interpretation of rock head due to the existence of corestone. The input data were analysed by geostatistical methods. It is found that the range in semivariogram is about 300m, and the variance of gneiss is greater than that of granite. It is because the granite data analysed came from almost single uniform rock mass(i.e.Seoul granite), but gneiss data came from the rock mass(i.e. Gyeonggi gneiss complex experienced several metamorphic metamorphic processes.

• Tunnel and Underground Space
• /
• v.13 no.2
• /
• pp.138-152
• /
• 2003

Three-dimensional computer modeling using FLAC3D had been carried out fur evaluating the thermal-mechanical stability of a high-level radioactive waste repository excavated in several hundred deep location. For effective modeling, a FISH program was made and the geological conditions and rock properties achieved from the drilling sites in Kosung and Yusung areas were used. Sensitivity analysis fer the stresses and temperatures from the modeling designed utilizing fractional factorial design was carried out. From the sensitivity analysis, the important design parameters and their interactions could be determined. From this study, it was found that deposition hole spacing is the most important parameter on the thermal and mechanical stability. The second and third most important parameters were disposal tunnel and buffer thickness.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.6
• /
• pp.832-840
• /
• 2019

Recently, pollution from gunpowder due to shell shootings at military drilling sites has raised various environmental concerns. The purpose of this study is to predict the contamination level of RDX in the soil area of the firing range zone near Anwol river watershed, the study site, and the intake area, Anwol river and Imjin river, as a function of time and space. In this study, a multimedia model was developed to predict the variation of RDX contamination by rainfall. The range of the medium was limited to soil, water, and sediment, and excluded the atmosphere, taking into account the physical and chemical properties of RDX with low vapor pressure and low Henry's constant. The pollutant levels of the waters of compartments, including the last section of the Imjin River affecting the water intake, was compared with the environmental standard for RDX.

• Tunnel and Underground Space
• /
• v.30 no.1
• /
• pp.63-75
• /
• 2020

When tunnel is excavated via drilling and blasting, the excessive overbreak is the primary cause of personal or equipment safety hazards and increasing the cost of the tunnel operation owing to additional ground supports such as shotcrete. The practical management of overbreak is extremely difficult due to the complex causative mechanism of it. The study examines the relationship between rock mass characteristics (unsupported face condition, uniaxial compressive strength, face weathering and alteration, discontinuities- frequency, condition and angle between discontinuities and tunnel contour) and the depth of overbreak through using feed-forward artificial neuron networks. Then, Overbreak Resistance Factor (ORF) has been developed based on the weights of rock mass parameters to the overbreak phenomenon. Also, a new concept of tunnel overbreak management system using ORF has been suggested.

• Geomechanics and Engineering
• /
• v.19 no.1
• /
• pp.93-104
• /
• 2019

Anomalies and/or fractured grounds not detected by the surface geophysical and geological survey performed during design stage may cause significant problems during tunnel excavation. Many studies on prediction methods of the ground condition ahead of the tunnel face have been conducted and applied in tunneling construction sites, such as tunnel seismic profiling and probe drilling. However, most such applications have focused on the drill and blast tunneling method. Few studies have been conducted for mechanized tunneling because of the limitation in the available space to perform prediction tests. This study aims to predict the ground condition ahead of the tunnel face in TBM tunneling by using an electrical resistivity tomography survey. It compared the characteristics of each electrode array and performed an investigation on in-situ tunnel boring machine TBM construction site environments. Numerical simulations for each electrode array were performed, to determine the proper electrode array to predict anomalies ahead of the tunnel face. The results showed that the modified dipole-dipole array is, compared to other arrays, the best for predicting the location and condition of an anomaly. As the borehole becomes longer, the measured data increase accordingly. Therefore, longer boreholes allow a more accurate prediction of the location and status of anomalies and complex grounds.

• Tunnel and Underground Space
• /
• v.34 no.1
• /
• pp.28-53
• /
• 2024

In general, high-level radioactive waste (HLW) generated as a result of nuclear power generation should be disposed within the country. Determination of the disposal site and host rock for HLW deep geological repository is an important issue not only scientifically but also politically, economically, and socially. Considered host rock types worldwide for geological disposal include crystalline rocks, sedimentary rocks, volcanic rocks, and salt dome. However, South Korea consists of various rock types except salt dome. This paper not only analyzed the geological and rock mechanical characteristics on a nationwide scale with the preliminary results on various rock type studies for the disposal host rock, but also reviewed the characteristics and possibility of various rock types as a host rock through deep drilling surveys. Based on the nationwide screening for host rock types resulted from literature review, rock distributions, and detailed case studies, Jurassic granites and Cretaceous sedimentary rocks (Jinju and Jindong formations) were derived as a possible candidate host rock types for the geological disposal. However, since the analyzed data for candidate rock types from this study is not enough, it is suggested that the disposal rock type should be carefully determined from additional and detailed analysis on disposal depth, regional characteristics, multidisciplinary investigations, etc.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.4
• /
• pp.261-276
• /
• 2002

Recently, for the purpose of choosing reasonable and economical construction, the decision making analyses, such as VE (Value Engineering) and LCC (Life Cycle Cost), are generally performed. But, these methods have some limitations for the application to subway tunnel construction method. So, the AHP (Analytical Hierarchy Process) analysis is applied to determine relative importance for obtaining objectivity in quantitative analysis. And, the LCSC (Life Cycle Social Cost) method is developed to account for the social loss and risk by tunnel construction. From the case of the subway ${\bigcirc}{\bigcirc}$ lot, those methods are very useful to decision making analysis. And, in that case, both quantitative and quantitative analysis appraisement, the drilling and blasting method is evaluated useful alternative proposal in comparing with the cut and cover method.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.2
• /
• pp.101-111
• /
• 2004

In order to guarantee the stability of a tunnel and its optimum design, it is very important to obtain enough ground investigation data. In realty, however, it is not the case due to the limitation of measuring spatially distributed data and economical reasons. Especially, there are regions where drilling is impossible due to civil appeal and mountainous topology, and it is also difficult to estimate rock mass classes quantitatively with only geophysical exploration data. In this study, therefore, 3 dimensional multiple indicator kriging (3D-MI kriging), which can incorporate geophysical exploration data and drill core data off a tunnel center line, is proposed to cope with such problems. To this end, two dimensional mutiple indicator kriging, which is one of the geostatistical techniques, is extended for three dimensional analysis. Also, the proposed 3D-MI kriging was applied to determine the rock mass classes by RMR system for the design of a Kyungbu express rail way tunnel.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.1
• /
• pp.51-62
• /
• 2001

In-situ stress measurement using AE (Acoustic Emission) and DRA (Deformation Rate Analysis) is usually carried out under uniaxial loading in the laboratory and it consumes delay time from drilling to testing. Therefore, it should be considered how the lateral stress and delay time influence on the test results for the in-situ stress determination. As the delay time increased, the accuracy of estimating the pre-stress decreased. The pre-stress of the specimen loaded only axially was determined within an error of less than 9% (using AE) and 4% (using DRA). And the specimen on which axial pre-stress and the confining pressure were loaded had an error of less than 17% (using AE) and 14% (using DRA). The results of AE and DRA for field specimens were very similar with each other but smaller than those of hydraulic fracturing method.