• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.3
• /
• pp.100-106
• /
• 2013

In this paper, in order to analyze lightning impulse response characteristics in combined installations of SPDs and RCDs, surge protection coordination between SPDs and RCDs are experimentally investigated by using the combination wave generator. Six different types of single-phase residual current operated circuit-breakers with integral overcurrent protection for household and similar uses(RCBOs) being present on the domestic market are tested according to KS C IEC 61009-1 standard. As a result, when a class I SPD is located on the source side of an RCBO, all kinds of specimens are able to provide the proper coordination between the SPD and RCBOs without nuisance tripping, unintended operation or damage due to test impulse currents. However, in the case that the class II SPD is located on the load side of RCBOs, a lot of L-N mode injected currents is split into the RCBO, and a few RCBOs are damaged. Coordination between SPDs and RCDs is not valid and a role of SPDs is of no use. When combining SPDs with RCDs, it is necessary to select SPDs and RCDs in consideration of the protection voltage level of metal oxide varistor embedded in RCDs.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.1
• /
• pp.64-70
• /
• 2014

In this paper, the new LLCL filter is proposed for grid connected three-phase PWM inverter for passive damping. LLCL filter inserts a small inductor in the branch of the capacitor of the traditional LCL filter to compose a series resonant circuit to reduce the switching-frequency component on grid current. Using LLCL filter, the switching-frequency current ripple components can be attenuated much better than the LCL filter, leading to a decrease in the total inductance. However, the resonance phenomena caused by zero impedance from the addition of LC branch in LLCL filter can be a big problem. Resonance phenomena of LLCL filter can be a source of grid system instability, so proper damping methods are required. However, it is difficult to apply a passive damping method in the conventional LLCL filter, because the damping resistor increase impedance of the LC branch. Therefore, switching frequency component of grid current can not much attenuated by low Q of LC series resonance effect. In this paper, a new LLCL filter is proposed to overcome the conventional LLCL filter with passive damping. The validity of the proposed method is proven by simulation and experimental result.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.552-558
• /
• 2016

Goethite, ${\alpha}$-FeOOH have various applications such as absorbent, pigment and source for magnetic materials. Goethite particles were synthesized in a two step process, where $Fe(OH)_2$ were synthesized in nitrogen atmosphere using $FeSO_4$ as a raw material in the first process, and after that acicular goethite particles were obtained in an air oxidation process of $Fe(OH)_2$ in highly alkaline aqueous solution. Their phase and microstructure were investigated with XRD and FE-SEM. It was found that the morphology of goethite and the ratio of length-to-width (aspect ratio) of acicular goethite are dependent on the some factors such as R value ($OH^-/Fe^{2+}$), air flow rate and pH conditions. In particular, R value has the strongest influence on the synthesized goethite morphology. It is considered that the optimal value R is 4.5 because X-ray diffraction peaks of goethite have the highest intensity at that value. Morphology of goethite particles was controlled by air flow rates, showing that their size and aspect ratio are getting smaller and decrease, respectively as air flow rate increases. The largest goethite particle obtained is about 1,500 nm in length and 150 nm in diameter.

• Korean Journal of Soil Science and Fertilizer
• /
• v.28 no.3
• /
• pp.287-294
• /
• 1995

This study demonstrates the influence of environmental conditions, other than iron, on pyoverdin production by fluorescent Pseudomosonas. In slightly acidic pH conditions(pH 6), cell yield was reduced while the siderophore production per cell yield was increased. The optimum temperatures for the siderophore production and cell yield was $19^{\circ}C$ and $28^{\circ}C$ for 7NSK2 and $12^{\circ}C$ and $19^{\circ}C$ for ANP15. The carbon and nitrogen balance showed that at low C : N ratio of the growth medium (higher nitrogen concentration), both cell yield and siderophore production was reduced. Use of different carbon sources revealed that citrate as a carbon source facilitated iron uptake and resulted in a significant reduction in siderophore production. However, at the late exponential phase, the iron content in the cell biomass was not significantly different from those grown in glucose or succinate. From these results it can be suggested that the environmental factors other than iron may also influence siderophore production by fluorescent pseudomonas.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.12
• /
• pp.957-962
• /
• 2014

We present a method to quantitatively measure the thermal conductivity of one-dimensional nanostructures by utilizing scanning thermal wave microscopy (STWM) at a nanoscale spatial resolution. In this paper, we explain the principle for measuring the thermal diffusivity of one-dimensional nanostructures using STWM and the theoretical analysis procedure for quantifying the thermal diffusivity. The SWTM measurement method obtains the thermal conductivity by measuring the thermal diffusivity, which has only a phase lag relative to the distance corresponding to the transferred thermal wave. It is not affected by the thermal contact resistances between the heat source and nanostructure and between the nanostructure and probe. Thus, the heat flux applied to the nanostructure is accurately obtained. The proposed method provides a very simple and quantitative measurement relative to conventional measurement techniques.

• Mass Spectrometry Letters
• /
• v.9 no.1
• /
• pp.30-36
• /
• 2018

A quantitation method for free amino acids in human serum was developed using a stepwise-dilution method and a bimodal cation exchange (CEX)/hydrophilic interaction liquid chromatography (HILIC)-tandem mass spectrometry system equipped with an electrospray ionization source (ESI/MS/MS). This method, which was validated using quality control samples, was optimized for enhanced selectivity and sensitivity. Dithiothreitol (DTT) was used as a reducing agent to prevent the oxidation of a serum sample ($50{\mu}L$), which was then subjected to stepwise dilution using 3, 30, and 90 volumes of acetonitrile containing 0.1% formic acid. Chromatographic separation was performed on an Imtakt Intrada Amino Acid column ($50mm{\times}3mm$, $3{\mu}m$) in mixed mode packed with CEX and HILIC ligands embedded in the stationary phase. Underivatized free amino acids were eluted and separated within 10 min. As a result of the validation, the precision and accuracy for the inter- and intraday assays were determined as 2.11-11.51% and 92.82-109.40%, respectively. The lowest limit of quantification (LLOQ) was $0.5-4.0{\mu}g/mL$ and the matrix effect was 80.22-115.93%. The proposed method was successfully applied to the quantitative analysis of free amino acids in human serum.

• Journal of Life Science
• /
• v.7 no.2
• /
• pp.107-111
• /
• 1997

To remove dissolved $NH_{4}$$^{+}$ in the aquaculture system, one ammonia oxidizing bacterium, Nitrsomonas sp. PK1, was isolated from samples collected in many aquacultural place and sludges of waste water. The stationary phase of this atrain was reached after 9 days, and the maximum $NO_{2}$ production was shown from 3 days to 9 days. In the selective medium, 0.1% of glucose was the good carbon source for growth. However, the $NO_{2}$productivity was repressed by the addition of glucose to the medium. When $Zn^{++}$ ion was supplemented to the medium, growth and the $NO_{2}$ productivity was increased, 10mM of $ZnCl_{2}$ was the optimal concentration for growth and 1 mM of $ZnCl_{2}$ was the optimal concentration for the production of $NO_{2}$, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3100-3106
• /
• 2014

This paper develops power measurement system with multiple sensor input channels (voltage-8 channels and current-10 channels) that simultaneously can monitor power components for both supply and load side of power system. The hardware implementation of the proposed system is based on TMS320C42 DSP and signal processing program algorithm to calculate power components use the definition of IEEE Standard 1459-2010 related power quality. The performance of the developed system is tested by using standard ac power source device, and the test results showed that accuracy of the developed system is less than 0.2 %. Also, field test of the proposed system in the three-phase and four-wire power system was implemented. Simultaneous multiple channel measurement and analysis of power components in commercial and industrial electrical power system using the proposed system will be necessary to reduce power quality problems.

• The KIPS Transactions:PartD
• /
• v.11D no.4
• /
• pp.855-864
• /
• 2004

Programmers can be got the test-related information for implementation without interference of source code complexity by use of the formal specification. Especially the external inputs and system responses can be represented precisely by formal specification in testing phase of web-based software systems. This paper suggests a method of extracting test cases by use of formal specification. Object-Z formal specification represents various test-related information for complex functions of web-based applications. State Transition Models could be built from the formal specification so that test scenarios were extracted from STDs from the highest level to detail levels. The target system for verification of this method is a web-based banking system which is necessary to be secured and critical on errors. This method would be an important factor in automatizing test procedure for web-based application software systems combining the user-base test technique.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.301-301
• /
• 2010

2010년경 2.5G APD 시장은 3, 000억원 규모로 증가하는데 이는 FTTH 망의 확산에 힘입은 바 크다. 이와 같이 중요한 APD 소자는 현재 광통신 부품시장을 석권해 가고 있는 대만, 중국 업체들은 제조기술을 갖고 있지 않고 주로 미국-일본 기술에 의존하고 있기 때문에 Niche market으로 중요한 부품이라 할 수 있다. APD의 증폭은 높은 전기장에 의해 얻어지는데, 이 때문에 메사형 구조로는 신뢰성을 확보하기 어렵게 되고 따라서 평면형(Planar) 구조로 설계-제작하게 된다. APD 소자는 증폭층의 너비에 의해 APD의 이득-대역폭이 정해지므로 증폭층 폭을 정확하게 조절하는 것은 매우 중요하다. 증폭층의 폭은 에피 성장과 같은 높은 정밀성을 갖는 장비에 의해 조절하는 것이 아니라, Planar 구조의 특성상 Zn-확산에 의해 조절하게 된다. 대부분의 경우 Zn-확산은 Zn 또는 $Zn_3P_2$를 증착하여 drive-in 시키는 방법을 사용하는데, 이 경우 Zn가 interstitial site를 치고 들어감으로 인해 캐리어 농도가 $2{\times}10^{17}\;cm^{-3}$ 정도로 낮게 형성된다. 따라서 높은 인가 바이어스에서 p-side로 공핍층이 전개되기 때문에 증폭층의 폭을 조절하기가 매우 어렵다. 이 현상은 APD 제작에 있어서 수율과 관련이 깊다. 따라서 APD의 증폭층 폭을 tight하게 조절하기 위해서는 p-type 캐리어 농도를 높일 수 있는 gas-phase 확산 방식의 개발이 필요하다. 이 방식에는 Ampoule과 같은 closed tube 방식과 확산로와 같이 Gas를 지속적으로 흘려주면서 확산시키는 open-tube 방식이 있다. Ampoule 방식은 캐리어 농도 측면에서는 가장 좋은 방식이나, Ampoule의 size 및 온도 균일성 등으로 인해 생산성에 문제가 있다. 따라서 open-tube 방식의 확산기술개발은 매우 중요하다 할 수 있다. 본 연구에는 rapid thermal annealing (RTA) 방법에 의한 $Zn_3P_2$ 고체의 확산 방식과 DEZn MO source에 의한 Gas 확산 방식을 바탕으로 InP로의 확산된 Zn원자와 doping의 분포를 비교하였다. 실험결과, Gas 확산방식의 경우 Zn원자가 더욱 더 깊게 확산이 되었으며, 확산된 원자의 대부분이 도펀트로 작용함을 확인할 수 있었다.