• 한국응용과학기술학회지
• /
• 제24권2호
• /
• pp.160-166
• /
• 2007

The rheological properties and surface tensions of polymer solutions and polymer-surfactant mixed solutions were investigated. The polymers used in this study were a homopolymer of acrylic acid crosslinked with an allyl ether of pentaerythritol, an allyl ether of sucrose, or an allyl ether of propylene (CARBOMER), acylate/C10-30 alkyl acylate crosspolymer (AAAC), and ammonium acryloydimethyltaurate/VP copolymer (ADTV). A solubilizing agent PEG-40 hydrogenated castor oil (HCO-40) and an emulsifying agent polyoxyethylene (20) sorbitan monostearate (POLYSORBATE 60) made the micelles intervening between AAAC polymers, resulting in the increase of viscosity. However, HCO-40 made this behavior over the wider range of surfactant concentration than POLYSORBATE 60. From the view point of surface tensions in the same range of surfactant concentration, AAAC/HCO-40 solution showed the area of increasing surface tension with surfactant concentration in contrast to the AAAC/POLYSORBATE 60 solution showing no increasing area.

• Environmental Analysis Health and Toxicology
• /
• 제7권3_4호
• /
• pp.69-79
• /
• 1992

Recently, concerns of water pollution and health risks caused by synthetic detergents have emerged, as the use of various detergents has increased It has been suggested that some surfactants are cocarcinogens. The surfactants tested were linear alkylbenzene sulfonate, sodium lauryl sulfate, polyoxyethylene sorbitan monooleat (tween 80), and the mutagens were 1-nitropyrene, N -methyl- N'-nitro-N -nitrosoguanidine, benzo (a) pyrene, and aflatoxin B$_1$. This study was undertaken to investigate the effects of surfactants on the activity of mytagens using the Ames mutagenic assay with Salmonella typhimurium TA98, TA100. The results were summarized as follows: 1. The surfactants have no mutagenic activity of themselves. 2. Higher doses of surfactants than 100 $\mu\textrm{g}$/plate reduced the number of revertants. It is assumed that the reduction would inhibited cell growth. 3. When the comutagenic ratio is defined as the ratio between mutagenic activity itself and the activity with mutagen and surfactant (drinking water quality standard), LAS showed the comutagenic ratio 0.86-1.17 and SLS 0.74-1.10 as well. According to the comparisons, it could not be recognised for the comutagenicity of drinking water quality standard of surfactant. 4. As increasing the amount of mutagens, the designated amount of surfactant did not affected the mutagen's activity statistically. From the above result, syunthetic surfactants do not present mutagenicity and comutagenicity in the microbial assay.

• Membrane and Water Treatment
• /
• 제4권1호
• /
• pp.11-25
• /
• 2013

Emulsion liquid membrane (ELM) process suffers from emulsion instability problem. So far, emulsion produced by mechanical methods such as stirrer and homogenizer has big size and high emulsion breakage. This paper discussed the application of emulsion produced by sonicator to extract cadmium in a batch ELM system. The emulsions consist of N,N-Dioctyl-1-octanamine (trioctylamine/TOA), nitrogen trihydride (ammonia/NH4OH), sorbitan monooleate (Span 80), and kerosene as carrier, stripping solution, emulsifying agent, and organic diluent, respectively. Effects of comprehensive parameters on extraction efficiency of Cd(II) such as emulsification time, extraction time, stirring speed, surfactant concentration, initial feed phase concentration, carrier concentration, volume ratio of the emulsion to feed phase, and pH of initial feed phase were evaluated. The results showed that extraction efficiencies of Cd(II) greater than 98% could be obtained under the following conditions: 15 minutes of emulsification time, 4 wt.% of Span 80 concentration, 4 wt.% of TOA concentration, 15 minutes of extraction time, 250 rpm of stirring speed, 100 ppm of initial feed concentration, volume ratio of emulsion to feed phase of 1:5, and initial feed pH of 1.53.

• 한국응용과학기술학회지
• /
• 제14권1호
• /
• pp.53-59
• /
• 1997

Spin finish(NSFs) for synthetic fiber were prepared. NSF-3 was proved to be the best spin finish by testing the properties and emulsion stability, etc. of NSFs. NSF-3 prepared by blending of spindle oil 70g, paraffin wax 10g, glyceryl mono-oleate 5g, POE(10) nonylphenyl ether 4g, POE(20) sorbitan tri-oleate 4g, Na-dioctyl sulfosuccinate 4g, antistatic agent 2g and water 1g was excellent in its characteristics. Optimum physical conditions of nylon filament treated with NSF-3 according to the number of revolution of oil roller were obtained at conditions of 5.5rpm in the number of revolution of oil roller, 1.21% of oil pick up, and denier 69.2D.

• 한국응용과학기술학회지
• /
• 제20권1호
• /
• pp.44-50
• /
• 2003

We studied on the preparation and evaluation of O/W type microemulsion containing "wax, liquid paraffine and quaternary ammonium salt". And also it was obtained to stability of microemulsions by mono ethylene glycol(MEG) addition. The microemulsions were generally prepared at 96${\sim}$97$^{\circ}C$ by the phase inversion method. We used polyoxyethylene(20) sorbitan monooleate(POE(20)SMO) and distearyl dimethyl ammonium chloride(D.D.A.C.) as the emulsifiers at microemulsion preparation. From the results, we could get best condition for microemulsion preparation, in case of oil phase, montanic ester wax ; 1.1wt%, paraffine wax ; 1.1wt%, liquid paraffine ; 3.1wt%, propylene glycol ; 0.6wt% and ethylene glycol monobutyl ether ; 0.6wt%, when the ratio(wt%) of D.D.A.C. and POE(20)SMO were 2 : 3. And also we could obtained that the distributed particle size of the final microemulsions were about 8${\pm}$1.5nm and the mean particle size was 7${\pm}$0.5nm. We got following results from final microemulsions that the percent of transmittance; 96${\sim}$98% at 700nm. And the microemulsion blended with MEG of 5${\sim}$15wt% showed smaller particle size and more stable distribution than non-containing MEG.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2003년도 총회 및 춘계학술발표회
• /
• pp.418-421
• /
• 2003

Surfactant enhanced in-situ soil flushing was peformed to remediate the soil and groundwater at an oil contaminated site, and the effluent solution was treated by the chemical treatment process including DAF(Dissolved Air Flotation). A section from the contaminated site(4.5m$\times$4.5m$\times$6.0m) was selected for the research, which was composed of heterogeneous sandy and silt-sandy soils with average Hydraulic conductivity of 2.0$\times$10$^{-4}$ cm/sec. Two percent of sorbitan monooleate(POE 20) and 0.07% of iso-prophyl alcohol were mixed for the surfactant solution and 3 pore volumes of surfactant solution were injected to remove oil from the contaminant section. Four injection wells and two extraction wells were built in the section to flush surfactant solution. Water samples taken from extraction wells and the storage tank were analyzed by GC(gas-chromatography) for TPH concentration with different time. Five pore volumes of solution were extracted while TPH concentration in soil and groundwater at the section were below the Waste Water Discharge Limit(WWDL). Total 18.5kg of oil (TPH) was removed from the section. The concentration of heavy metals in the effluent solution also increased with the increase of TPH concentration, suggesting that the surfactant enhanced in-situ flushing be available to remove not only oil but heavy metals from contaminated sites. Results suggest that in-situ soil flushing and chemical treatment process including DAF could be a successful process to remediate contaminated sites distributed in Korea.

• Food Science and Biotechnology
• /
• 제18권5호
• /
• pp.1161-1172
• /
• 2009

Food nanoemulsion systems consisting of water and oleoresin capsicum (OC), polyoxythylene sorbitan esters (Tween 20, 40, 60, and 80), propylene glycol (PG), sucrose monostearate (SM), and their corresponding mixtures were formulated to use as food vehicles. Tween 80 produced OC nanoemulsions with stable dispersions as one-phase systems, and the dertermined emulsification efficiencies clearly distinguished the ability of the various surfactants to emulsify OC. The nanoemulsions were prepared by both ultrasonication and self-assembly, and the nanoemulsion areas were determined using phase diagrams by measuring the sizes of the emulsions. One-phase nanoemulsions were presented, with a multiple cloudy region and phase separation that were dependent on the particle size of the emulsion. The OC nanoemulsions prepared by ultrasonication using systems of OC/Tween 80/water, OC/Tween 80/water+PG, and OC/Tween 80/water+SM, resulted in particle sizes ranging from 15 to 100 nm. Finally, the nanoemulsions maintained their initial sizes during storage, ranging from 65 to 92 nm.

• 한국미생물생명공학회:학술대회논문집
• /
• 한국미생물생명공학회 2000년도 Proceedings of 2000 KSAM International Symposium and Spring Meeting
• /
• pp.100-107
• /
• 2000

In a recently developed strategy for in-situ treatment of polychlorinated biphenyls (PCB), bioaugmentation was used in conjunction with a surfactant, sorbitan trioleate, as a carbon source for the degrader bacteria, along with the monoterpene, carvone, and salicylic acid as inducing substrates. Two bacteria were used for soil inoculants, including Arthrobacter sp. st. B1B and Ralstonia eutrophus H850. This methodology achieved 60% degradation of PCBs in Aroclor 1242 after 18 weeks in soils receiving 34 repeated applications of the degrader bacteria. However, an obvious limitation was the requirement for soil mixing after every soil inoculation. In the research reported here, bioaugmentation and biostimulation treatment strategies were modified by using the earthworm, Pheretima hawayana, as a vector for dispersal and mixing of surface-applied PCB-degrading bacteria and soil chemical amendments. Changes in microbial biomass and microbial community structure due to earthworm effects were examined using DNA extraction and PCR-DGGE of 16S rDNA. Results showed that earthworms effectively promoted biodegradation of PCBs in bioaugmented soils to the same extent previously achieved using physical soil mixing, and had a lesser, but significant effect in promoting PCB biodegradation in biostimulated soils treated with carvone and salicylic acid. The effects of earthworms were speculated to involve many interacting factors including increased bacterial transport to lower soil depths, improved soil aeration, and enhanced microbial activity and diversity.

• Macromolecular Research
• /
• 제11권2호
• /
• pp.104-109
• /
• 2003

A microcellular, which combines a rubber with the conventional formulation of styrene/divinylbenzene/sorbitan monooleate/water system, was prepared using high internal phase emulsion (HIPE) polymerization. Although the open microcellular foam with low density from the conventional HIPE polymerization shows highly porous characteristics with fine, regular and isotropic structure, the one having much smaller cell size is desirable for various applications. In this study, a polybutadiene was introduced to reduce the cell size with comparable properties. Major interests were focused on the effects of rubber concentration and agitation speed on the cell sizes and compression properties. Scanning electron microscopy was used to observe the microcellular morphology and compression tests were conducted to evaluate the stress-strain behaviors. It was found that the cell size decreased as rubber concentration increased, reflecting a competition between the higher viscosity of continuous phase and the lower viscosity ratio of dispersed to continuous phases due to the addition of high molecular weight rubber into the oil phase of emulsion. A correlation for the average cell size depending on agitation speed was attempted and the result was quite satisfactory.

• 한국응용과학기술학회지
• /
• 제21권4호
• /
• pp.335-344
• /
• 2004

In this work, the properties as polishing wax for automobile of O/W type microemulsion containing wax, liquid paraffine and quaternaryammonium salt was investigated. The microemulsions were prepared at $96{\sim}97^{\circ}C$ by the phase inversion method, and polyoxyethylene(20) sorbitan monooleate (POE(20)SMO) and distearyl dimethyl ammonium chloride(D.D.A.C) as the emulsifiers were used. The mean particle size of the rnicroemulsions was about 7${\pm}$0.5nm and as the properties of polishing wax, gloss increased degree, water resistant gloss degree, initial and final contact angle after water resistance were tested. The result was that the value of water resistantance and contact angle were decreased with increasing amount of POE(20)SMO and D.D.A.C., while the gloss degree values did not affected. And the rnicroemulsion blended with mono ethylene glycol(MEG) of 5${\sim}$15wt% showed smaller particle size and more stable particle size distribution than without MEG. Finally, this microemulsion showed more excellent values of gloss degree, the water resistant gloss degree and contact angle, than two kinds of commercial polishing wax for automobile.