• 한국세라믹학회지
• /
• 제38권6호
• /
• pp.545-550
• /
• 2001

본 연구에서는 분사연소합성(SCS)을 위한 기초단계로서 용액연소합성에 대한 거동을 살펴보고자 알루미나 합성을 모델로 하였으며 이를 위해 전구체에 대한 열분해거동, 그리고 각 온도에서의 평형종 분압 계산 및 합성과정을 조사하였다. 각각의 열중량 분석(TGA) 결과 산화제와 환원제(연료)의 열분해 이력이 서로 다르게 나타났으며, 열역학 응용 프로그램인 ChemSag에 의한 평형종 분압의 계산에서 연소속도를 저하시킬 수 있는 $CO_2$와 수증기 가스 분압이 상당부분 존재하였다. 산화제/환원제 혼합물의 열분석(DTA/TG) 결과 산화제와 환원제의 열분해 거동의 차이, 그리고 매우 작은 시료의 양으로 인해 263$^{\circ}C$에서 발열피크가 매우 작게 나타났다. 열분석 시료에 비해 발열 에너지를 높이기 위해 산화제와 환원제 혼합 전구체를 비이커에서 증기압을 조절하며 가열시켜 본 결과 27$0^{\circ}C$에서 $\alpha$-Al$_2$O$_3$생성물을 얻을 수 있었다. 따라서 분사연소합성 반응을 통해 세라믹 원료를 합성하기 위해서는 연소과정 중 열분해 거동과 평형종의 분압을 고려하여야 한다.

• 한국세라믹학회지
• /
• 제35권5호
• /
• pp.451-457
• /
• 1998

$Li_2$$ZrO_3$ powder which is one of the candidates of breeding materials for the fusion reactor was syn-thesized by a precipitation-combustion process. Although precipitates from the reaction between zirconium nitrate and citric acid were existed in a precursor solution. $Li_2$$ZrO_3$ could easily be obtained by using the mixed fuel of urea and citric acid in stoichiometric composition. The phases of as-synthesized powder con-sisted of $Li_2$$ZrO_3$ and small amounts of $Li_6$$Zr_2O_3$ and $Li_2$$ZrO_3$ The latter phases disappeared after the cal-cination at $1100^{\circ}C$ for 2 h. The primary particle size and the specific surface area of as-synthesized powders were smaller than 20nm and 10-14 $M^2$/g, respectively. The primary particle size of the precipitation-combustion synthesized powders was affected by the size of precipitates present in a precursor solution.

• 한국세라믹학회지
• /
• 제35권10호
• /
• pp.1078-1084
• /
• 1998

금속 질산염과 urea를 사용하여 연소합성법에 의해 LaCrO3 분말을 제조하고, 용액의 pH를 HNO3와 NH4OH로 조절한 후, 용매의 가열방법에 따른 연소 생성물인 LaCrO3의 형상을 고찰하였다. 연소생성물의 수율은 용액의 pH에 의해 크게 좌우되었다. 용액의 pH가 0.7~4 사이에서는 90% 이상의 수율이 얻어졌으나, 5 이상 또는 0.5 이하의 pH에서는 수율이 크게 감소하였다. 한편, 연소생성물의 형상은 용액의 pH에 무관하였고 용액의 가열방법에 좌우되었다. 용액을 저항가열법으로 가열하여 연소반응시킨 경우의 분말은 미세한 일차입자들이 2차원적으로 연결된 응집체를 형성하고 있었으나, 마이크로파를 인가하여 가열한 경우에는 용액의 pH에 관계없이 미세한 LaCrO3 분말이 얻어졌다. BET 분석 결과, 마이크로파 가열에 의해 얻어진 입자의 비표면적은 25~32m2/g으로 저항가열법으로 가열한 경우의 10-14m2/g에 비해 더 큰 값을 보였다. 이러한 결과는 마이크로파에 의한 연소반응물의 균일한 가열이 연소생성물의 2차원적인 강항 응집체 형성을 억제할 수 있음을 보여 주었다.

• 한국분말재료학회지
• /
• 제27권5호
• /
• pp.394-400
• /
• 2020

Molybdenum trioxide (MoO₃) is used in various applications including sensors, photocatalysts, and batteries owing to its excellent ionic conductivity and thermal properties. It can also be used as a precursor in the hydrogen reduction process to obtain molybdenum metals. Control of the parameters governing the MoO₃ synthesis process is extremely important because the size and shape of MoO₃ in the reduction process affect the shape, size, and crystallization of Mo metal. In this study, we fabricated MoO₃ nanoparticles using a solution combustion synthesis (SCS) method that utilizes an organic additive, thereby controlling their morphology. The nucleation behavior and particle morphology were confirmed using ultraviolet-visible spectroscopy (UV-vis) and field emission scanning electron microscopy (FE-SEM). The concentration of the precursor (ammonium heptamolybdate tetrahydrate) was adjusted to be 0.1, 0.2, and 0.4 M. Depending on this concentration, different nucleation rates were obtained, thereby resulting in different particle morphologies.

• 한국재료학회지
• /
• 제11권9호
• /
• pp.797-801
• /
• 2001

In this study, the solution combustion method was employed to synthesize stoichiometric mullite, and hence the attrition process was employed to prepare ultrafine mullite particles with nano size. The thermal decomposition behavior and partial pressure of equilibrium species of both oxidizer and fuel were considered during solution combustion process. The synthesized product was mullite phase with 40 nm crystalline size, and the alumina contents of the product by TEM/EDS quantity analysis was 3.12$\pm$04 mole. The result showed that the synthesized mullite was almost close to the it's stoichiometric composition. For attrition process, the dispersion behavior of the mullite suspension was controlled and was comminuted with the condition of 800 rpm for 4 hours using 0.3 mm zirconia ball media. As a result of comminution, the mean particle size was 80 nm.

• 한국재료학회지
• /
• 제17권7호
• /
• pp.382-385
• /
• 2007

[ $LaFeO_3$ ] powders were prepared as the oxidation catalyst materials to reduce the emission of particulate matters from diesel engine and their catalytic effects on the oxidation of carbon were investigated. Solution combustion method was employed for the powder synthesis, which uses highly exothermic and selfsustaining reactions. In this study $LaFeO_3$ powders were synthesized at $400^{\circ}C$ as varying the ratio ($\Phi$) of fuel (citric acid) and oxidizer (metal nitrate), and their phase and carbon ignition property were examined. As $\Phi$ decreases, the crystallinity of synthesized $LaFeO_3$ powders enhanced. By calcining at $700^{\circ}C$, all the powders synthesized at various $\Phi$ fully crystallized. The calcined $LaFeO_3$ powders showed carbon ignition temperature as low as $501{\sim}530^{\circ}C$, which implied the decrease of the ignition temperature by $120{\sim}150^{\circ}C$.

• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.731-737
• /
• 1997

TixZr1-xC(0$0^{\circ}C$, 5.1 mm/sec respectively. The relative density, three point flexural strength, and the hardness of composites, which was sintered at 190$0^{\circ}C$ for 60 min by using hot-pressing under a pressure of 30 MPa, were 99%, 525 MPa and 24 GPa respectively.

• Journal of Electrochemical Science and Technology
• /
• 제6권1호
• /
• pp.16-25
• /
• 2015

Transition metal oxide nanocrystalline materials are playing major role in energy storage application in this scenario. Nickel oxide is one of the best antiferromagnetic materials which is used as electrodes in energy storage devices such as, fuel cells, batteries, electrochemical capacitors, etc. In this research work, nickel oxide nanoparticles were synthesized by combustion route in presence of organic fuels such as, glycine, glucose and and urea. The prepared nickel oxide nanoparticles were calcined at 600℃ for 3 h to get phase pure materials. The calcined nanoparticles were preliminarily characterized by XRD, particle size analysis, SEM and EDAX. To prepare nickel oxide electrode materials for application in supercapacitors, the calcined NiO nanoparticles were mixed with di-methyl-acetamide and few drops of nafion solution for 12 to 16 h. The above slurry was coated in the graphite sheet and dried at 50℃ for 2 to 4 h in a hot air oven to remove organic solvent. The dried sample was subjected to electrochemical studies, such as cyclic voltammetry, AC impedance analysis and chrono-coulometry studies in KOH electrolyte medium. From the above studies, it was found that nickel oxide nanoparticles prepared by combustion synthesis using glucose as a fuel exhibited resulted in low particle diameter (42.23 nm). All the nickel oxide electrodes have shown better good capacitance values suitable for electrochemical capacitor applications.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 춘계총회 및 연구발표회 초록집
• /
• pp.53.2-53
• /
• 2003

• Archives of Metallurgy and Materials
• /
• 제66권4호
• /
• pp.991-995
• /
• 2021

In this paper, synthesize MoO₃ particles with various particle properties by control growth influence factors was mainly studied. The experimental conditions were established in molar ratio of Mo:urea and pH levels. The plate-type of MoO₃ particles were formed without proceeding any established conditions, but the rod-shape particles were formed by adjusting molar ratio of Mo:urea. Also, different ranges of the particle size were formed by adjusting experimental conditions. Through the results, it was confirmed that particles with a size in the range of 300 ~ 400 nm were obtained by adjusting precursor concentration and the micrometer size of particles were formed by increase pH levels. The properties of the particles formed accordingly by setting various factors that can affect the growth process of MoO₃ particle was analyzed as variables and the particle growth behavior was also observed.