• Journal of Biomedical Engineering Research
• /
• v.15 no.4
• /
• pp.389-394
• /
• 1994

The age-hardening behavior and the structural changes in a commercial dental Au-Ag-Cu-Pd alloy were investigated by means of hardness test, optical and scanning electron microscopic observation, energy dispersive spectroscopy and X-ray diffraction study. The drastic reduction in hardness by prolonged aging occurred after a rapid increase in hardness at the initial stage by the isothermal aging at $350^{\circ}C$. This softening was due to the broad precipitates formation of the lamellar structure which was composed of the f.c.t. AuCu I ordered f.c.t. phase containing Pd and the f.c.c. Ag-rich $\alpha$1 solid solution f.c.c.phase containing Au.

• Journal of Korea Foundry Society
• /
• v.37 no.6
• /
• pp.207-216
• /
• 2017

This study investigated the effects of the addition of Zn, Ca, and SiC on the microstructure and mechanical properties of Mg-Al alloys. The tensile properties of homogenized Mg-xAl (x = 6, 7, 8, and 9 wt.%) alloys increased with increasing Zn content by the solid-solution strengthening effect. However, when the added Zn content exceeded the solubility limit, the strength and ductility of the alloys decreased greatly owing to premature fracture caused by undissolved coarse particles or local melting. Among the Mg-xAl-yZn alloys tested in this study, the AZ74 alloy showed the best tensile properties. However, from the viewpoints of the thermal stability, castability, and tensile properties, the AZ92 alloy was deemed to be the most suitable cast alloy. Moreover, the addition of a small amount (0.17 wt.%) of SiC reduced the average grain size of the AZ91 alloy significantly, from $430{\mu}m$ to $73{\mu}m$. As a result, both the strength and the elongation of the AZ91 alloy increased considerably by the grain-boundary hardening effect and the suppression of twinning behavior, respectively. On the other hand, the addition of Ca (0.5-1.5 wt.%) and a combined addition of Ca (0.5-1.5 wt.%) and SiC (0.17 wt.%) increased the average grain size of the AZ91 alloy, which resulted in a decrease in its tensile properties. The SiC-added AZ92 alloy exhibited excellent tensile properties (YS 125 MPa, UTS 282 MPa, and EL 12.3%), which were much higher than those of commercial AZ91 alloy (YS 93 MPa, UTS 192 MPa, and EL 7.0%). The fluidity of the SiC-added AZ92 alloy was slightly lower than that of the AZ91 alloy because of the expansion of the solid-liquid coexistence region in the former. However, the SiC-added AZ92 alloy showed better hot-tearing resistance than the AZ91 alloy owing to its refined grain structure.

• Journal of Korea Foundry Society
• /
• v.7 no.2
• /
• pp.108-113
• /
• 1987

Al-Cr alloy with composition in the range from 1.5 wt% to 10 wt% Cr were rapidly solidified from the melt by the single roller method. The supersaturated solid solution was obtained up to 6 wt% Cr in Al-Cr alloy for $20{\mu}m$ thickness. Lattice parameter decreased with increasing Cr content at the rate of 0.00456A per wt% Cr up to 6 wt% Cr. Microhardness increased with increasing Cr content at the rate of $10\;Kg/mm^2$ per wt% Cr up to 6 wt% Cr. Microhardness measurements on the Al-6 wt% Cr supersaturated solid solution annealed isothermally showed no sign of age hardening. Decomposition temperature, determined by lattice parameter changes and microhardness changes, was $470^{\circ}C$ for Al-6 wt% Cr supersaturated solid solution. Transmission electron microscopy showed that decomposition within one hour below $400^{\circ}C$ occurred at grain boundaries only, and also the additional decomposition within grains being evident at $450^{\circ}C$ The coarse precipitate structure showed at $500^{\circ}C$ and $550^{\circ}C$, respectively. The coarse precipitate structure is considered $Al_7Cr$.

• Korean Journal of Materials Research
• /
• v.24 no.4
• /
• pp.201-206
• /
• 2014

TiC-21 mol% Mo solid solution (${\delta}$-phase) and TiC-99 mol% Mo solid solution (${\beta}$-phase), and TiC-(80~90) mol% Mo hypo-eutectic composite were deformed by compression in a temperature range from room to 2300 K and in a strain rate range from $4.9{\times}10^{-5}$ to $6.9{\times}10^{-3}/s$. The deformation behaviors of the composites were analyzed from the strengths of the ${\delta}$- and ${\beta}$-phases. It was found that the high strength of the eutectic composite is due primarily to solution hardening of TiC by Mo, and that the ${\delta}$-phase undergoes an appreciable plastic deformation at and above 1420 K even at 0.2% plastic strain of the composite. The yield strength of the three kinds of phase up to 1420 K is quantitatively explained by the rule of mixture, where internal stresses introduced by plastic deformation are taken into account. Above 1420 K, however, the calculated yield strength was considerably larger than the measured strength. The yield stress of ${\beta}$-phase was much larger than that of pure TiC. A good linear relationship was held between the yield stress and the plastic strain rate in a double-logarithmic plot. The deformation behavior in ${\delta}$-phase was different among the three temperature ranges tested, i.e., low, intermediate and high. At an intermediate temperature, no yield drop occurred, and from the beginning the work hardening level was high. At the tested temperature, a good linear relationship was held in the double logarithmic plot of the yield stress against the plastic strain rate. The strain rate dependence of the yield stress was very weak up to 1273 K in the hypo-eutectic composite, but it became stronger as the temperature rose.

• Journal of Powder Materials
• /
• v.9 no.5
• /
• pp.303-306
• /
• 2002

P/M high speed steels with various Co contents were fabricated by gas atomization and Canning/HIP process. As Co content in P/M high speed steel increased, hardness, transverse rupture strength and yield strength in compressive testing increased due to solid solution hardening of Co in matrix. Especially, PM high speed steels with Co have high deformation resistance to repeated compressive loading.

• 연구논문집
• /
• s.29
• /
• pp.163-171
• /
• 1999

A new titanium alloy system. Ti-xFe-ySi (x,y=0-4 wt%). was designed and characterized with the point at low cost and high strength for casting applications. Fe improved room and elevated temperature mechanical properties owing to solid solution hardening and beta phase stabilization. Si yielded titanium silicides and Si addition over 1 wt% resulted in poor ductility due to coarse silicide chains at prior beta boundaries. The optimum composition was found to be Ti-4Fe-(0.5-1)Si in the viewpoint of tensile strength and ductility which are comparable to the Ti-6Al-4V. The metal-mould reaction was also examined for Ti-xFe and Ti-xSi binary alloy system. The thickness of surface reaction layer w as not affected significantly with Fe content, while it was decreased with Si content. In the Ti-4Si alloy, no reaction layer was found. The depth of surface hardening layer was about $200\mum$ regardless of the mould materials.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.4
• /
• pp.187-194
• /
• 2007

A transmission electron microscope (TEM) investigation has been performed on the precipitation of $L2_1$-type $Ni_2AlTi$ phase in B2-ordered NiAl system. The hardness after solution treatment is high in NiAl-Ti alloys suggesting the large contribution of solid solution strengthening in this alloy system. However, the amount of age hardening is not large as compared to the large microstructural variations during aging. At the beginning of aging, the $L2_1$-type $Ni_2AlTi$ precipitates keep a lattice coherency with the NiAl matrix. By longer periods of aging $Ni_2AlTi$ precipitates lose their coherency and change their morphology to the globular ones surrounded by misfit dislocations. Misfit dislocations, which are observed on {100} planes of H-precipitates have the Burgers vector of a <100> with a pure edge type. The lattice misfits of NiAl-$Ni_2AlTi$ system is estimated from the spacings of misfit dislocations to be 1.1% at 1273 K. The lattice misfits decrease with increasing aging temperature in this system.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.5
• /
• pp.249-256
• /
• 2006

Structural studies have been performed on precipitation hardening found in $L1_2$ ordered ${\gamma}^{\prime}-Ni_3(Al,Ti)$ alloys using transmission electron microscopy. A uniform solid solution of ${\gamma}^{\prime}-L1_2$ ordered phase supersaturated with Ni can be obtained by solution annealing in a suitable temperature range. The ${\gamma}^{\prime}$ phase hardens appreciably by the fine precipitation of disordered ${\gamma}$. The shape of ${\gamma}$ precipitates formed during aging is initially spherical or round-cubic and grow into platelets as aging proceeds. High resolution electron microscopy revealed that the ${\gamma}$ precipitates are perfectly coherent with the matrix ${\gamma}^{\prime}$ as long as the ${\gamma}$-precipitates are plates. The loss of coherency initiates by the introduction of dislocations at the ${\gamma}/{\gamma}^{\prime}$ interface followed by the step formation at the dislocations. The ${\gamma}$ precipitates become globular after the loss of coherency. The strength of ${\gamma}^{\prime}-Ni_3(Al,Ti)$ increases over the temperature range of experiment by the precipitation of fine ${\gamma}$ particles. The peak temperature where a maximum strength was obtained shifted to higher temperature.

• Korean Journal of Materials Research
• /
• v.17 no.8
• /
• pp.420-424
• /
• 2007

Precipitation behavior has been studied in NiTi-based ordered alloy using transmission electron microscopy. The hardness after solution treatment is high in NiTi alloy suggesting the large contribution of solid solution strengthening in this alloy system. However, the amount of age hardening is not large as compared to the large microstructural variations during aging. At the beginning of aging, the $L2_1-type$ $Ni_2AlTi$ precipitates keep a lattice coherency with the NiTi matrix. By longer periods of aging $Ni_2AlTi$ precipitates lose their coherency and change their morphology to the globular ones surrounded by misfit dislocations. Misfit dislocations, which are observed on {100} planes of H-precipitates have the Burgers vector of a <100> with a pure edge type. The lattice misfits of $NiTi-Ni_2AlTi$ system is estimated from the spacings of misfit dislocations to be 1.3% at 1273 K. The lattice misfits decrease with increasing aging temperature in this system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.238-238
• /
• 2012

현재 국내 주얼리(gold alloy) 제품을 생산함에 있어 주조 방법은 크게 대기 중 주조(흡입주조) 방법과 진공주조 방법으로 나누어진다. 국내 주얼리 제조업체의 약 90%이상이 대기 중에서 주조하는 흡입주조방법을 통해 제품을 제작하고 있고, 국외의 경우, 대다수 진공주조방법을 통해 제품을 제작하고 있다. 본 연구에서는 주얼리 제품을 생산할 때 사용되는 합금재료(master alloy)가 동일한 조건에서 주조방법을 달리하여 각각 24개씩 총 48개의 14K yellow gold alloy 제품을 제작한 후 열처리를 통해 각각의 기계적, 물리적 특성분석을 비교 분석하였다. EPMA (Electron Probe Micro Analysis)분석을 통해 합금재료 및 제품의 구성성분을 조사하였고, ICP-MS (Inductively Coupled Plasma Mass Spectroscopy)를 사용하여 성분에 대한 정량분석을 실시하였다. 용체화처리(solid solution treatment)는 $700^{\circ}C$, 30분의 조건으로 실시하였고, 시효경화처리(age-hardening)는 $200{\sim}300^{\circ}C$의 온도범위에서 $50^{\circ}C$ 간격으로 실시하였다. 열처리 전과 후 시료의 grain 들의 배열 및 size 변화를 관찰하기 위해 식각 후 OM (optical microscope) 및 SEM (Scanning Electron Microscope)를 통해 분석하였다. 열처리 전 제품의 경도측정결과 대기 중 흡입주조방법 및 진공 주조방법을 통해 제작된 제품이 각각 119 Hv, 126 Hv로 나타났고, 용체화 처리 후 98 Hv, 92 Hv로 감소하였다. 시효경화 처리 후의 경도변화는 대기 중 흡입주조 및 진공주조방법을 통해 제작된 제품 모두 $270^{\circ}C$에서 각각 154 HV, 166 HV로 가장 높은 경도 값을 나타내었고, $270^{\circ}C$ 이상에서는 과시효(over aging)현상으로 인해 경도 값이 다시 감소하는 경향을 나타내었다. EPMA mapping 분석을 통해 주조방법에 따라 각각 제품의 구성성분분포도를 확인하였다. 이를 통해 열처리 전 다소 불균일하게 분포되었던 성분들이 열처리 후 균일해짐을 확인할 수 있었다.