• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.5-8
• /
• 2005

In this report the developing trends of several clean and green propellants have been summarized. A low-acid clean propellant has been developed, which substantially reduced the content of hydrochloric acid(HCl) in the solid rocket exhaust. Although the chlorine-free approach is now preferred, this technology has not been proved yet. Another acid suppression effect of Magnalium(Mg-Al Alloy) was investigated. Reports says that the concentration of HCl could be reduced to approximately one-fifth of conventional propellant. Many 'green' propellants with low toxicity are being developed for next-generation post-boost propulsion systems, in which combustion research on the Al or Mg fine metal particles with hot steam in various stoichiometric conditions are being performed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.6
• /
• pp.736-742
• /
• 2015

The effect of pressure on 1,3-dipolar cycloaddtion has been studied by means of FT-IR and NMR spectroscopy. Pressure accelerates 1,3-dipolar cycloaddition without solvent or catalyst. This simple and inexpensive method eliminates the need for work-up or purification. The method is expected to be applied to the synthesis of binders for solid rocket propellants.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.232-235
• /
• 2011

A typical unsteady internal ballistic analysis model was developed to take account the erosive burning of a solid rocket motor. The variance of local velocity and pressure along grain surface were analyzed by using the continuity and momentum equation. The coefficients of erosive burning were drew from comparing experiment data with analysis. It was investigated that the grain shapes of propellant affect the erosive burning.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.191-195
• /
• 2009

In the solid rocket propellant combustion, dynamic phase change from solid to liquid to vapor occurs across the melt layer. During the burning surface, micro scale bubbles form as liquid and gas phases are mixed in the intermediate zone between the propellant and the flame. The experimentally measured thickness of this layer called the foam layer is approximately 1 micron at 1 atmosphere. In this paper, we present a new melting layer model derived from the classical phase change theory. The model results show that the surface of burning grows and propagate uniformly at a velocity of $r=ap^n$.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.2
• /
• pp.26-36
• /
• 2007

The thermal response characteristics of nozzle liner for a solid rocket motor applying highly aluminized PCP or HTPB propellant with slotted tube grain have been investigated. The SEM photographs of aluminum oxide particles taken from nozzle liner show that the PCP propellant with the finer and less contents of oxidizer can offer greater possibility for increasing aluminum agglomeration than the HTPB propellant. The PCP propellant shows locally greater mechanical erosion at 4 circumferential areas of the nozzle entrance in line with grain slot due to the impingement of large particles, but the HTPB propellant shows greater thermochemical ablation at the nozzle blast tube, the throat insert and the exit cone because of relatively much more mole fraction of $H_2O\;and\;CO_2$ in combustion gases.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.70-77
• /
• 2014

In this paper, the development of unique model of the 2.75 inch rocket propulsion system is described. Recently developed korean 2.75 inch rocket propulsion system shows the improvement of a flame stability resulted from a change in the configuration of propellant grain, and of an incidental ignition protection function using the EMI(electromagnetic interference) filter on ignition system. Moreover it is shown that a directional flight stability is improved by increasing the number of fins and changing the nozzle configuration. Static firing test and thermal shock test were conducted for the validation before flight, and flight test of 210 rounds of rockets was conducted to verify the trajectory uniformity. In addition, intellectual property issues can be overcome with the unique korean 2.75 inch rocket motor as well as the performance improvement.

• Membrane Journal
• /
• v.22 no.4
• /
• pp.235-242
• /
• 2012

Ammonium perchlorate (AP) is primarily derived from the process of liquid incineration treatment when dismantling a solid rocket propellant. A series of batch dead-end nanofiltration (NF) and reverse osmosis (RO) membrane experiments were conducted to explore the retention mechanisms of AP under various hydrodynamic and solution conditions. Low levels of silicate type of siloxane had been detected through the GC/MS and FTIR analysis of liquid solutions extracted from solid ammonium perchlorate composite propellant (APCP). It is indicated that NF/RO membranes fouling in the presence of APCP was mainly attributed to the AP interactions because the concentration of silicate type of siloxane was negligible compared to that of AP. The osmotic pressure of AP was presumably resulted in the flux declines ranging from 13 to 17% in the case of the application of low-pressure (551 and 896 kPa for NF and RO) compared to those in application of high-pressure. The retention of AP by NF/RO membranes significantly varied from approximately 10 to 70% for NF and 26 to 87% for RO, depending on the operating and solution water chemistry conditions. The results suggested that retention efficiency of AP was fairly increased by reducing concentration polarization (i.e. application of low-pressure and stirring speed of 600 rpm) and increasing the pH of a solution. The result of this study was also consistent with the previous modeling of 'solute mass transfer of NF/RO membranes' and demonstrated that hydrodynamic and solution water chemistry conditions are to be a key factor in the retention of AP by NF/RO membranes.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.371-377
• /
• 2020

Combustion instability occurred in the combustion test of solid rocket motor with large aspect ration Length/Diameter (L/D) and cylinder-slot grain. As a result of spectral analysis of the pressure perturbation, it was confirmed that the central axis longitudinal frequency was dominant, so that the length of the cylinder part was increased to eliminate the coincidence with acoustic node. In addition, acoustic modal analysis and flow analysis were performed to analyze the cause of instability by unsteady flow structure in solid rocket motors. It was confirmed that the combustion instability is reduced by quantitative comparison of the amplitude and frequencies of the pressure inside the combustion chamber using the grain shape before and after the design change. Finally, a combustion test was performed to verify that the combustion instability was resolved as in the flow analysis.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.147-150
• /
• 2005

Space launch vehicles mainly use the liquid-propellant propulsion system which has easy thrust control ability and high specific impulse for that the payload like satellite and spacecraft should be entered into exact orbit. However, the liquid-propellant propulsion system is very difficult to develop because it is more complicate than the solid rocket propulsion system and demands very high technology. In space launch vehicle developing procedure the system design level is very important thing to reduce cost, shorten schedule, and improve the performance. The system design process was introduced for selecting the best liquid-propellant propulsion system on this paper.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.320-323
• /
• 2009

There is many considerations of the composition development of propellant, performance analysis according to temperature, ablation condition of heat-resistant material, etc. in the solid rocket motor development process. Performance analysis of the motor according to nozzle expansion ratio is one of this process and an important factor to decide the motor performance. A Study is verified through anlaysis, motor manufacture and test.