• Journal of Soil and Groundwater Environment
• /
• v.19 no.3
• /
• pp.111-122
• /
• 2014

Partitioning interwell tracer test (PITT) is a method to quantify and qualify a site contaminated with NAPLs (Non-Aqueous Phase Liquids). Analytical description of PITT assumes that the injection-pumping well pair is on the line of the ambient groundwater flow direction, but the test-well pair could frequently be off the line in a real field site, which could be an erroneous factor in analyzing PITT data. The purpose of this work is to study the influence of the angle of the test-well pair on the ambient groundwater flow direction based on the result from PITT. From the experiments, it was found that the obliqueness of the test-well pair to the ambient groundwater flow direction could affect the tracer test resulting in a decreased NAPL estimation efficiency. In case of an oblique arrangement of the test-well pair to the ambient flow direction, it was found that the injection of a chase fluid could enhance the estimation efficiency. An increase of the pumping rate could enhance the recovery rate but it cannot be said that a high pumping rate can increase the test efficiency because a high pumping rate cannot give partitioning tracers enough time to partition into NAPLs. The results have a implication that because the arrangement of the test-well pair is a controlling factor in performing and interpreting PITT in the field in addition to the known factors such as heterogeneity and the source zone architecture, flow direction should be seriously considered in arranging test-well pair.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.6
• /
• pp.998-1003
• /
• 2011

This investigation was performed to determine the hydraulic conductivity coefficient and water holding capacity for a specified compaction forces which are the amount of mechanical energy applied to the porous granule (PG) volume. Most current specifications of minerals and perlite as growth media require to be compacted to a specified density, which in general is equivalent to a certain percentage of laboratory compaction. The water holding capacity of the saturated PG was very large at potential above -1 bar compared with perlite, but very little water remained below this value. The water holding capacity and hydraulic conductivity characteristics of graded PG amended with the ground coir less than 2 mm in diameter were also determined from pressure outflow data. The saturated hydraulic conductivity of the saturated and compacted PG was slightly lower by more than one tenth order of magnitude at equal matric potentials of perlite, but when expressed on the basis of equal water deficits, the conductivity of PG was higher at all but the smallest deficits than those of perlite.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.3
• /
• pp.55-66
• /
• 2012

To investigate the hysteresis of the suction stress in unsaturated weathered mudstone soils (CL), matric suction and volumetric water content were measured in both drying and wetting processes using Automated Soil-Water Characteristics Curve Apparatus. The drying and wetting processes in unsaturated soils were reproduced in the test; the drying process means to load matric suction to spill pore water from the soils, and the wetting process means to unload matric suction to inject pore water into the soils. Based on the measured result, Soil Water Characteristic Curve(SWCC)s were estimated by van Genuchten model (1980). SWCCs have nonlinear relationship between effective degree of saturation and matric suction. The hysteresis in SWCCs between drying and wetting processes occurred. As a result of estimating Suction Stress Characteristic Curve(SSCC) using Lu and Likos model (2006), the suction stress rapidly increased in the low level of matric suction and then increased slightly. Also, the hysteresis in SSCCs between drying and wetting processes occurred. In order to design geo-structures and check its stability considering unsaturated soil mechanics, therefore, it is more reasonable that the SSCC of drying process should be applied in the condition of rainfall infiltration and the SSCC of wetting process in the condition of evaporation or drainage.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.3
• /
• pp.253-259
• /
• 2010

This experiment was conducted to evaluate water use efficiency of barley, wheat, and millet as a substitution crop for rice of fallow paddy field. Dry weight (DW), evapotranspiration, and transpiration of crop grown on the lysimeters controlled with 5 levels of groundwater table (GWT), 0, 25, 50, 75, and 100 cm were evaluated for optimum GWT and water use efficiency. All the lysimeters randomized with four replication arrangements were filled up sandy loam and were adjusted to the constant bulk density treated with twice water infiltration from bottom side to upper side of lysimeter. DW of barley, wheat, and millet in the plot of 0cm GWT that is saturated soil showed 34.9%, 44.7%, and 37.1% of that in the plot of 100 cm GWT, respectively showing a serious obstacle in crop growth. Evapotranspiration ratios calculated by evapotranspiration volume (mL) per DW were 166~605 mL for barley, 136~481 mL for wheat, and 81~418 mL for millet showing the order of barley > wheat > millet. Evapotranspiration ratio was increased with decrease of groundwater table that is the condition of moisture saturation. Estimation of GWT for maximum DW of wheat was 76 cm, and those of barley and millet were 100 cm below. The volumetric moisture content of lysimeter soil with cropping was markedly decreased as increase of crop growth because moisture supplying capability by capillary rise of water was less than amount of moisture required by crop.

• Korean Journal of Plant Resources
• /
• v.29 no.4
• /
• pp.393-399
• /
• 2016

This study was conducted to elucidate the photosynthetic response to the environment and establish optimum cultivation conditions for the Korean endemic plant, Aster koraiensis. Photosynthetic characteristics according to growth stage, light, CO₂, and soil water potential were investigated. During the first year of transplanting, photosynthetic rates were drastically increased until June, after which they slowly declined, During the second year, photosynthetic rates declined throughout the entire growth period. The highest level of light compensation point was shown the early growth stage. Photosynthetic rates affected by intercellular CO₂ concentration were maintained or decreased over the CO₂ saturation point. The lowest CO₂ compensation point was 16.1 μmol·mol⁻¹ during March. The morphological changes of leaves were observed due to shading with chlorophyll contents increasing. Photosynthetic rates were higher at 0% and 50% shading treatments than at 75%. There were rarely any morphological changes of leaves due to soil moisture, however, changes to leaf compactness were observed. Photosynthetic rate, apparent quantum yield, and respiration rate increased, whereas water use efficiency decreased over −25 kPa of soil moisture.

• Journal of Applied Biological Chemistry
• /
• v.54 no.2
• /
• pp.79-83
• /
• 2011

Over-application of nitrogen fertilizer keeps increasing the salinity in the soils of greenhouse in domestic agriculture. In order to remove the excess amounts of soil nitrate, soil microorganisms which have high capacity of nitrate uptake were isolated from the upland soils and their nitrate uptake activities were measured. Strain GS2 was able to remove 50 mM nitrate within 12 h. After sequence comparison analysis of 16S rRNA gene, the strain was identified and named as Bacillus sp. GS2. When the growth and nitrate uptake activities were measured, maximal values were obtained at $30-40^{\circ}C$ and $37^{\circ}C$, respectively; however, both were optimal at pH 6-8. In the media containing 50 mM nitrate, Bacillus sp. GS2 removed 43 mM nitrate which is corresponding to 86% removal. Similar amounts of nitrate removal were observed at the nitrate concentrations up to 300 mM, showing a saturation in nitrate uptake at concentrations above 50 mM. These results imply that Bacillus sp. GS2 can be a good candidate for the microbial remediation of accumulated environmental nitrate because of its excellent growth and nitrate uptake activity.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.30 no.2
• /
• pp.55-66
• /
• 1988

This study was conducted to investigate the various engineering properties and correlationshops among the soil constants of alluvial clayey deposits distributed in the bay of Asan and their results are summarized as follows : 1. Grain size distribution of soil was consisted of 12 % of clay, 46-73 % of silt, 2-23 % of sand, and as for the consistency characteristics, 26-36 % of liquid limit, 18-21 % of plastic limit and 6-16 % of plastic index, and so the soil belonging to as a lower plastic nonorganic clay, it's specific gravity was 2,66-2.70, and the location on the plastic chart was approximately above the A-line. Z The natural moisture content and unit weight were 30-43 % and 1.76-1.87 g I cm$_3$, respectively, and according to increment of natural moisture content, the unit weight was decreased, and the initial void ratio and degree of saturation were shown of 0,87-1119 and 92- 100 %, most of saturated. 3. Cone resistance value which was shown 2.4 - 6.5 kg / $cm^2$ was a little lower and it was increased with the depth of layer and shown the formular $q_c=0.7_z+1.32$. 4. Unconfined compression strength was about 0.18-0.43kg /$cm^2$, cu, 0.1-0.22kg / $\psi$, $2-6^{\circ}$ under uu-test condition of triaxial, and CCU, 0.08-0.3 kg/cm , $\psi$, $12-18^{\circ}$ under the condition of cu-test. 5. Pre-consolidation load of characteristics of consolidation was 0.4-0.8 kg / $cm^2$, compression index, about 0.17-0.33. 6. Liquid limit and plastic index were incresased with the increment of clay content but most of alluvial clay was appeared as a normal through non-activity clay soil shown more natural moisture content than liquid limit, and their relationship as follows : LL=0.38( cy+54.8), PI=0.836(LL -17.8), PI =0.468(LL -0.48) 7. The initial void ratio presented correlationship of positive among clay content, natural moisture content and liquid limit, and that of reverse with unit weight, and their results as follws : $e_o=0.024(w_n+0.2)$, $e_o=e_o=0.0003c_y+0.0005 LL+0.0151 W_n+\frac{3.58}{r-t}-1.52$ 8. It was shown that the compression index has correlationship of postive among the clay content, liquid limit, plastic index, natural moisture content and initial void ratio, and their relationships as follows ; $c_c=0.44(e_o-0.47)$, $c_c=0.001$

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.7 no.1
• /
• pp.40-49
• /
• 2004

This work carried out to define the characteristic of Cymbidium kanran habitat at Mt. Halla in Jejudo, Korea from the ecological point of view including geological and topographical features, air and soil temperature, relative humidity, fluctuations of light intensity, habitat vegetation, distribution altitude, area limit, and etc. And another goal of this study consider the conservation counterplan of the cymbidium habitat. Natural distribution areas of the cymbidium were observed more abundantly on the well drained south and east-facing slopes. Soil acidity was ranged from pH 4.1 to 5.3, and electric conductivity was ranged from 176.4 to 299.9 us/cm (average 215.3 us/cm). Base-saturation percentage of the habitat soil was below 50%, bulk density 0.42g/$cm^2$, particle density 2.05g/$cm^2$, humus content 26%, total nitrogen 0.82%, available phosphate 4.2 mg/kg, exchangeable potassium 0.63 Cmol/kg, calcium 0.44 Cmol/kg and magnesium 0.67 Cmol/kg. Annual mean air temperature was $15.4^{\circ}C$, however, air temperature was ranged $11.7{\sim}18.2^{\circ}C$ in spring, $21.2{\sim}23.8^{\circ}C$ in summer, $12.8{\sim}22.0^{\circ}C$ in fall and $5.5{\sim}7.8^{\circ}C$ in winter season. Annual mean soil temperature at depth of 10cm was $13.2^{\circ}C$ And minimum value was recorded $4.7^{\circ}C$ on January, and maximum value $22.5^{\circ}C$ on August. Relative humidity was ranged 90.8~94.7% in summer, 80.8~91.5% in fall and 77.6~84.2% in winter season. Minimum value was 56.5% on December, and maximum value was 100% on July and August. Light intensities were ranged from 400 to 1,800 lux at the greater part of Cymbidium kanran sites in Jejudo. Summer regarded as an lower light intensities was recorded to be range of 500~600 lux; however, autumn and winter were shown higher light regimes ranged from 3,500 to 3,800 lux. Therefore, one must be suprised that the cymbidium grow at the light condition of 6 lux (minimum) or 10,000 lux (maximum). Tree species keeping higher frequency rate and density were Eurya japonica, Camellia japonica, Castanopsis cuspidata, Carpinus laxiflora and Pinus densiflora. Number of trees growing in a 5${\times}$5m quardrat was 35 as an average, and proportion of evergreen versus deciduous was 5:1. Distribution altitude of the orchid habitat was ranged from 120m (low) to 840m (high) from sea level on the south facing slope of Mt. Halla, and was ranged eastern borderline of Gujwaup, Bukjejugun to western boundaries of Jungmundong, Seogwipo city. For the stable conservation of Cymbidium kanran habitat, sunlight regimes must be increased more by means of cutting trees or twigs in the site.

• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.5
• /
• pp.310-317
• /
• 2008

This study was carried out to investigate the factors of desalinization of the rainfall interception culture soils of Rubus sp. in Gochang-gun, Jeollabuk-do. Soil samples were collected from 85 different sites of the rainfall interception culture soils of Rubus sp. in Gochang-gun, Jeollabuk-do. The electrical conductivity in paste saturation of rainfall interception culture soils ranged from $1.0\sim28.4dS\;m^{-1}$ (average: $4.8dS\;m^{-1}$) and salt affected soil which EC was higher than $4dS\;m^{-1}$, covered nearly 55% of all field surveyed. Salts in rainfall interception culture soils were accumulated by increasing the cultivation period. Electrical conductivity in rainfall interception culture soils was positively correlated with water soluble anions such as chloride ion ($r=0.85^{**}$), nitrate ion ($r=0.94^{**}$), phosphate ion ($r=0.88^{**}$), and sulfate ion ($r=0.84^{**}$), respectively. As a result of desalinization experiments carried out by water management practices, the rinsing method was more effective than leaching method.

• Journal of Radiation Protection and Research
• /
• v.43 no.1
• /
• pp.29-38
• /
• 2018

Background: Radon contributing about 42% of annual average dose, mainly comes from soil. In this paper, standard measurement procedures for soil radon exhalation rate are suggested and their measurement uncertainties are analyzed. Materials and Methods: We used accumulation method for estimating surface exhalation rate. The closed-loop measurement system was made up with a RAD7 detector and a surface chamber. Radon activity concentrations in the system were observed as a function of time, with data collection of 5 and 15-minute and the measurement time of 4 hours. Linear and exponential fittings were used to obtain radon exhalation rates from observed data. Standard deviations of measurement uncertainties for two approaches were estimated using usual propagation rules. Results and Discussion: The exhalation rates (E) from linear approach, with 30 minutes measurement time were $44.8-48.6mBq{\cdot}m^{-2} {\cdot}s^{-1}$ or $2.14-2.32atom{\cdot}cm^{-2}{\cdot}s^{-1}$ with relative measurement uncertainty of about 10%. The contributions of fitting parameter A, volume (V) and surface (S) to the estimated measurement uncertainty of E were 59.8%, 30.1% and 10.1%, in average respectively. In exponential fitting, at 3-hour measurement we had E ranged of $51.6-69.2mBq{\cdot}m^{-2} {\cdot}s^{-1}$ or $2.46-3.30atom{\cdot}cm^{-2}{\cdot}s^{-1}$ with about 15% relative uncertainty. Fitting with 4-hour measurement resulted E about $51.3-68.2mBq{\cdot}m^{-2} {\cdot}s^{-1}$ or $2.45-3.25atom{\cdot}cm^{-2}{\cdot}s^{-1}$ with 10% relative uncertainty. The uncertainty contributions in exponential approach were 75.1%, 13.4%, 8.7%, and 2.9% for total decay constant k, fitting parameter B, V, and S, respectively. Conclusion: In obtaining exhalation rates, the linear approach is easy to apply, but by saturation feature of radon concentrations, the slope tends to decrease away from the expected slope for extended measurement time. For linear approach, measurement time of 1-hour or less was suggested. For exponential approach, the obtained exhalation rates showed similar values for any measurement time, but measurement time of 3-hour or more was suggested for about 10% relative uncertainty.