• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.48-56
• /
• 2016

In this study, to develop the lattice materials with a low environmental load for restoring the destroyed forest, 7 types of wood-concrete hybrid laminated materials were manufactured with domestic four softwoods, three hardwoods and concrete, and the effects of density of wood species on static bending strength performances were investigated. Bending MOEs of wood-concrete hybrid laminated materials increased with increasing density of wood species on the whole, and the values were higher than that of concrete by hybrid-laminating woods on the concrete. It was found that the measure values of bending MOEs were slightly lower than the calculated values calculated using equivalent cross-section method from MOE of each laminae of hybrid laminated materials and the difference between them was less than 10%. Bending proportional limit stresses of hybrid laminated materials showed 1.2-1.6 times higher than that of concrete by hybrid-laminating. Bending strength (MOR) of hybrid laminated materials increased with the density of wood species. By hybrid-laminating, the MOR of concrete was considerably increased. Therefore, it is considered that wood-concrete hybrid laminated materials can be applied as a materials with a low environmental load and durability for ecological restoration.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.6
• /
• pp.666-674
• /
• 2014

In this study, we investigated mechanical properties of Korean softwoods after applying thermal compression. Density of compressed woods was notably increased with thermal compression. In case of 50% compression set, density of Korean pine (Pinus koraiensis), Japanese red pine (P. densiflora), and Larch (Larix kaempferi) wood was increased by 71%, 74%, and 76%, respectively, when compared to the control group. The strength of woods was increased and quality of the woods became homogeneous with an increases in the compression set. On the 50% compression set, the compressive strength, bending strength, and hardness of Korean pine wood was increased by 76%, 83%, and 55%, respectively compared to the control group. Longitudinal compressive strengths of Japanese red pine wood increased by 69%, 130%, and 76%, respectively and those of Larch wood increased by 77%, 120%, and 44%, respectively. In thermal compression wood, mechanical properties of Larch wood was the highest, while those of Korean pine wood were the lowest. However, Japanese red pine wood showed the highest in the increase rate of mechanical properties after the thermal compression.

• Journal of Forest and Environmental Science
• /
• v.9 no.1
• /
• pp.10-18
• /
• 1993

The study was carried out to investigate the physical (Density, Percentage of latewood, Percentage of pore zone, Mean annual ring width) and mechanical (Compressive strength parallel to the grain, Compression perpendicular to the grain, Shearing strength) properties of some major northern softwoods and hardwoods. The physical and mechanical properties of each species are summerized as Table 2 and the relationship between physical and mechanical factors are discussed. The results of this study were as follows: Density and percentage of latewood are closely related to physical and mechanical properties, but percentage of pore zone and mean annual ring width are remotely related to physical and mechanical properties.

• Journal of Forest and Environmental Science
• /
• v.28 no.4
• /
• pp.268-277
• /
• 2012

Among the domestic softwoods, technical value of Pinus koraiensis small diameter logs which have comparatively low applicability was evaluated and sensitive characteristics and physical characteristics were investigated and analyzed for examining if it can be utilized as the interior decoration material. For the sensitive characteristics of Pinus koraiensis, wood figure, wood grain, wood color and odor were evaluated and for the physical characteristics, growth-ring width and latewood percentage, abrasion, density, shrinkage, swelling, absorption, roughness and hardness were evaluated. Then, the possibility to be developed as the interior decoration material was found. As the result of evaluating sensitive characteristics and physical characteristics of domestic Pinus koraiensis, wood figure, wood grain, color and scent clearly were judged to have excellent visual factor as the interior decoration material. And, physical characteristics were also judged to be excellent, so it is judged to be developed as the interior decoration material. Therefore, as the result of various forms of design pattern with domestic Pinus koraiensis small diameter logs, several patterns of interior decoration can be developed by characteristics of each side and colors of heartwood and sapwood. And, in the future, it can be applied to furniture design or interior decoration material for the proper use. Especially, it is considered to contribute to wood applying industry through the study on the quality of domestic small diameter logs which have low applicability.

• Journal of the Korea Furniture Society
• /
• v.21 no.2
• /
• pp.188-195
• /
• 2010

This study has been focused on the evaluation of domestic softwood timbers to replace imported timbers for woodcrafts and furniture-making. Figures on radial and tangential sections were observed with naked eyes. As the result of study on the figures appeared on the wood surface of 6 species of trees, flat grain and edge grain were clearly found from Taxus cuspidata. Juniperus chinensis and Ginkgo biloba had wavy grain figure and pigment figure, and blister figure was found in Pinus densiflora, Larix kaempferi showed pitch streak and irregular figures on its tangential section due to growth abnormalities. Wavy grain figure appeared weakly on near knot of Pinus koraiensis. The characteristic figures shown from each species of trees are expected to be used for crafts, sculptures, furniture, and interior decoration. They are also considered to have great potential to substitute imported timber sufficiently, which are currently used a lot for wood crafts and furniture-making.

• Journal of the Korea Furniture Society
• /
• v.19 no.6
• /
• pp.420-427
• /
• 2008

To study the suitability of chestnut as a cask for ripening traditional liquors, the absorption property for pure water, liquor with 30% alcohol content and ethanol with 95% alcohol content were investigated for five species. Oriental oak had the greatest amount of liquid absorption while chestnut had the smallest amount. The absorption amount linearly increased with increasing soaking time. The absorption amounts for each section were greatest in RT plane, and the difference between LR plane and LT plane was very small for all soaking conditions. The anisotropy of absorption amount for five species was greatest in Japanese cedar and was smallest in white mulberry on the whole. And the change of absorption amounts according to soaking conditions tended to decrease in softwoods and increase in hardwoods, and the difference among wood species was not clear. From this result, it was found that chestnut with a small absorption amount, regarding of soaking behavior, was a good material as a cask for ripening traditional liquors, whereas small diameter oriental oak with a great absorption amount was not suitable in this purpose.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.3
• /
• pp.16-22
• /
• 1995

The profiles of the heating temperature in three water vat temperatures (55, 66 and 77$^{\circ}C$) and the cooling temperature under the average ambient temperature of 3$^{\circ}C$ in 4 and 10cm depths from surface at the center of veneer bolts length showed similar patterns for Japanese larch (Larix leptolepis). Dahurian larch (Larix gmelinei) and Radiata pine (Pinus radiata). The difference of these core temperatures of 10cm depth from surface varied proportionally with the increase of vat temperatures. The average heating time based on final core temperature of 6$^{\circ}C$ lower than vat temperature required about 14.5 hours in vat temperature of 55$^{\circ}C$ and 13.5 hours in vat temperature of 66and 77$^{\circ}C$. Each internal temperature of 4 and 10cm depths from surface started to decrease from the beginning of cooling and after about two hours.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.2
• /
• pp.67-74
• /
• 1997

A relationship between drying resistance and moisture content was found for 24, 27 and 30mm thick boards, and 45, 51 and 57mm thick dimensions of Japanese larch. Dahurian larch and radiata pine in order to modify the kiln schedule by using time schedules. The amount of drying resistance for Dahurian larch lumber was the highest, and radiata pine lumber was the lowest, on the basis of the same moisture content range. Drying resistance increased curvilinearly as moisture content decreased, and was higher for thicker lumber than for thinner lumber, at a given moisture content. Combined drying resistance for the three board thicknesses and the three dimension thicknesses showed a comparatively strong for radiata pine and a Japanese larch, while a weak correlation for Dahurian larch as a function of two independent variables, thickness and moisture content of lumber, respectively.

• Journal of the Korean Society of Safety
• /
• v.22 no.6
• /
• pp.46-54
• /
• 2007

The purpose of this study was to examines the burning rate of fire retardant treated wood in the cone heater with a one-dimensional integral model. The wood samples used in this study were four species. The species of woods are Redwood, White oak, Douglas fir and Maple. Each sample was nominally 50mm thick and 100mm square. Samples were exposed to a range of incident heat fluxes 10 to $35kW/m^2$ using the cone heater. A one-dimension integral model has been used to predict burning rate, heat of gasification, flame heat fluxes, charring rate and char depth of samples. As a result measurement of mass loss rate, softwoods(Redwood and Douglas fir) has relatively low value than those for hardwoods(White oak and Maple). Average charring rate of woods in case of fire retardant treatment showed reduction effect of 41.29%, 50.00%, 48.18% and 60.82% for Redwood, Douglas fir, White fir and Maple, respectively. Almost all the predictions from integral model showed faster charring than those measured. Average difference between predictions and experimental data was 16%, 9.5% and 11.8% for N, F1 and F2 respectively. Water-soluble fire retardant used in this study find out more effect in hardwood than softwood from the result of measurement of mass loss rate and average charring rate.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.317-321
• /
• 2006

The investigation of the formation of organic sulfur compounds (i.e., odor species), mainly methyl mercaptan and demethyl suifide, during kraft pulping has been conducted, in which both hardwood and softwood species were used. It was discovered that there is an organic sulfur compounds formation phase transition point with respect to delignification extent. The transition point occurs at a kappa number of approximately 35 and 20 for softwoods and hardwoods, respectively. The results also showed that both low sulfidity and anthraquinone (AQ) addition are helpful to control the formation of theses organic sulfur compounds during kraft pulping. Whereas Hexenuronic acid (HexA) has contribution to Kappa number, the extended delignification not only lead to low pulp yield, but also be adverse to odor control. A significant in-digester odor reduction can be achieved if the pulping is to be terminated before phase transition point and combined with AQ addition.