• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.988-995
• /
• 2020

Air gun shock systems are commonly used as alternative explosion energy sources for underwater explosion (UNDEX) shock tests owing to their low cost and environmental impact. The airbag inflator of automotive airbag systems is also very useful to generate extremely rapid underwater gas release in labscale tests. To overcome the restrictions on the very small computational time step owing to the very fine fluid mesh around the nozzle hole in the explicit integration algorithm, and also the absence of a commercial solver and software for gas UNDEX of airbag inflator, an idealized airbag inflator and fluid mesh modeling technique was developed using nozzle holes of relatively large size and several small TNT charges instead of gas inside the airbag inflator. The objective of this study is to validate the results of an UNDEX response analysis of one and two idealized airbag inflators by comparison with the results of shock tests in a small water tank. This comparison was performed using the multi-material Arbitrary Lagrangian-Eulerian formulation and fluid-structure interaction algorithm. The number, size, vertical distance from the nozzle outlet, detonation velocity, and lighting times of small TNT charges were determined. Through mesh size convergence tests, the UNDEX response analysis and idealized airbag inflator modeling were validated.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.44 no.1
• /
• pp.60-70
• /
• 2021

Recently, with the development of technologies for the fourth industrial revolution, convergence and complex technology are being applied to aircraft, electronic home appliances and mobile devices, and the number of parts used is increasing. Increasing the number of parts and the application of convergence technologies such as HW (hardware) and SW (software) are increasing the No Defect Found (NDF) phenomenon in which the defect is not reproduced or the cause of the defect cannot be identified in the subsequent investigation systems after the discovery of the defect in the product. The NDF phenomenon is a major problem when dealing with complex technical systems, and its consequences may be manifested in decreased safety and dependability and increased life cycle costs. Until now, NDF-related prior studies have been mainly focused on the NDF cost estimation, the cause and impact analysis of NDF in qualitative terms. And there have been no specific methodologies or examples of a working-level perspective to reduce NDF. The purpose of this study is to present a practical methodology for reducing NDF phenomena through data mining methods using quantitative data accumulated in the enterprise. In this study, we performed a cluster analysis using market defects and design-related variables of mobile devices. And then, by analyzing the characteristics of groups with high NDF ratios, we presented improvement directions in terms of design and after service policies. This is significant in solving NDF problems from a practical perspective in the company.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.439-445
• /
• 2021

Low-cost, ultra-high-speed cameras, made possible by the development of image sensors and small displays, can be very useful in image processing and pattern recognition. This paper introduces an algorithm that corrects irregular lighting from a high-speed image that is continuously input with a slight time interval, and which then obtains an exposed skin color region that is the area of interest in a person from the corrected image. In this study, the non-uniform lighting effect from a received high-speed image is first corrected using a frame blending technique. Then, the region of interest is robustly obtained from the input high-speed color image by applying an elliptical skin color distribution model generated from iterative learning in advance. Experimental results show that the approach presented in this paper corrects illumination in various types of color images, and then accurately acquires the region of interest. The algorithm proposed in this study is expected to be useful in various types of practical applications related to image recognition, such as face recognition and tracking, lighting correction, and video indexing and retrieval.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.6
• /
• pp.1113-1122
• /
• 2020

Recently, as violent crimes of crime without reason (Korea : Do not ask), women and the elderly are getting serious. In the existing system, many CCTVs are installed, but it is difficult to prevent crime due to only follow-up measures after a crime occurs. This device prevents crime through this device for incidents in shaded areas and closed spaces such as apartments and buildings. To do this, we research this technology to develop products and software. It sends an alarm signal using communication technology to a specific place where you want to receive an event of an alarm or a CCTV device operated using image analysis big data technology and convergence sensor technology for a specific target of the behavior expected to be a crime or movement. Develop the device. This development device researches and develops this device and supplies low-cost devices to consumers, which is used as a device that predicts the occurrence of crime in advance, processes it as an alarm signal in real time, and transmits it, and constitutes a standalone device and a server. Will provide the device to be connected.

• Plant Journal
• /
• v.17 no.4
• /
• pp.53-60
• /
• 2021

The purpose of this study was to develop a portable vibration analyzer that is effective for acquiring and analyzing vibration data of rotating equipment of a power plant and a domestic vibration monitoring system manufacturer Nada Co., Ltd. The hardware of the developed portable vibration analyzer minimizes measurement errors by calibrating the measured values obtained through measurement uncertainty for calibration of the measuring devices in the system, and is composed of a signal processing device with high resolution through high speed data processing. The software structure implements a variety of vibration plots to execute a detailed analysis program, and applies algorithms to measure and remove noise caused by disturbances while operating a rotating machine. The developed product contributed greatly to increase the user's mobility and performance, as well as to reduce the purchase cost due to localization.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.219-225
• /
• 2022

The textile industry in Korea, the dyeing sector is an energy-intensive sector and has low per-unit productivity due to its labor-intensive nature. If the defective rate of dyed fabrics is high, additional costs are incurred due to an increase in production cost due to re-dyeing. Therefore, the goal of the dyeing factory was to minimize the defect rate rather than to save energy. It was difficult to check the dyeing state of the fabric in real time due to the risk of accidents due to burns or pressure when dyeing in a high-temperature and high-pressure environment. In this paper, a complex sensor that can measure the exhaustion rate of dye solution in the dyeing machine using turbidity, pH, and conductivity sensors was proposed, and the experimental method and experimental results were analyzed.

• International Journal of Computer Science & Network Security
• /
• v.22 no.7
• /
• pp.443-450
• /
• 2022

The method of studying 3D-technologies abroad and in Ukraine is considered. The analysis of educational resources and experience of use of the equipment in branch is carried out. The didactic principles of the educational process for 3D-printing specialists are determined. The use of FDM technology and the ability to minimize the occurrence of defects in the future have been studied. An analysis of the international experience of the educational process of relevant specialists in the field. The content of training for 3D printing specialists has been developed. The experience of using 3D-technologies is described and the list of recommendations for elimination of defects during production of products by means of additive technologies is made. The recommendations will be useful not only for beginners, but also for experienced professionals in additive technologies. The need to study such experience is the main condition for the development of enterprises in Ukraine that plan to automate their own production. A 3D printing engineer must know the basics of economics and marketing, because his responsibilities include optimizing workflows to reduce the cost and speed up printing. Therefore, the knowledge gained from practical experience presented and in building for learning 3D printing engineers by the authors will be important.

• International journal of advanced smart convergence
• /
• v.12 no.3
• /
• pp.1-12
• /
• 2023

A public address (PA) system installed in a building is a system that delivers alerts, announcements, instructions, etc. in an emergency or disaster situation. As for the products used in PA systems, with the development of information and communication technology, PA products with various functions have been introduced to the market. PA systems recently launched in the market may be connected through a single network to enable efficient management and operation, or use voice recognition technology to deliver quick information in case of an emergency. In addition, a system capable of locating a user inside a building using a location-based service and guiding or responding to a safe area in the event of an emergency is being launched on the market. However, the new PA systems currently on the market add some functions to the existing PA system configuration to make system operation more convenient, but they do not change the complex PA system configuration to reduce facility costs, maintenance, and management costs. In this paper, we propose a novel PA system configuration for buildings using audio networks and control hierarchy over peer-to-peer (Anchor) technology based on audio over IP (AoIP), which simplifies the complex PA system configuration and enables convenient operation and management. As a result of the study, through the emergency signal processing algorithm, fire broadcasting was made possible according to the detection of the existence of a fire signal in the Anchor system. In addition, the control device of the PA system was replaced with software to reduce the equipment installation cost, and the PA system configuration was simplified. In the future, it is expected that the PA system using Anchor technology will become the standard for PA facilities.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.1
• /
• pp.191-197
• /
• 2023

The purpose of the study was to provide an educational environment for designing and producing virtual reality practice contents that can be used in semiconductor production lines and clean rooms. Through this process, the user can acquire practical knowledge through experiences close to reality, such as experiencing the main semiconductor solar cell manufacturing facilities as well as procedural knowledge before and after entering the clean room.. In particular, it provides users with an immersion experience close to reality by creating an environment for experiential content necessary for semiconductor and solar cell manufacturing processes and clean room entrance procedure experiential content, which is expected to improve education immersion, realism, cost, efficiency, and education satisfaction. Depending on the characteristics of Dangerous, Impossible, Counter-productive etc, immersive content makes learners immersed in the learning content, induces proactive/active learning, and embodies the learning content, resulting in positive results in the field of improving educational effectiveness.

• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.247-257
• /
• 2023

Precise counting of cell number stands in important position within clinical and research laboratories. Conventional methods such as hemocytometer, migration/invasion assay, or automated cell counters have limited in analytical time, cost, and accuracy., which needs an alternative way with time-efficient in-situ approach to broaden the application avenue. Here, we present simple coding-based cell counting method using image analysis tool, freely available image software (ImageJ). Firstly, we encapsulated RFP-expressing bacteria in a droplet using microfluidic device and automatically performed fluorescence image-based analysis for the quantification of cell numbers. Also, time-lapse images were captured for tracking the change of cell numbers in a droplet containing different concentrations of antibiotics. This study confirms that our approach is approximately 15 times faster and provides more accurate number of cells in a droplet than the external analysis program method. We envision that it can be used to the development of high-throughput image-based cell counting analysis.