• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.66-66
• /
• 2008

Most of the properties of ITO films depend on their substrate nature, deposition techniques and ITO film composition. For the display panel application, it is normally deposited on the glass substrate which has high strain point (>575 degree) and must be deposited at a temperature higher than $250^{\circ}C$ and then annealed at a temperature higher than $300^{\circ}C$ in order to high optical transmittance in the visible region, low reactivity and chemical duration. But the high strain point glass (HSPG) used as FPDs is blocking popularization of large sizes FPDs because it is more expensive than a soda lime glass (SLG). If the SLG could be used as substrate for FPDs, then diffusion of Na ion from the substrate occurs into the ITO films during annealing or heat treatment on manufacturing process and it affects the properties. Therefore proper care should be followed to minimize Na ion diffusion. In this study, we investigate the electrical, optical and structural properties of ITO films deposited on the SLG and the Asahi glass(PD200) substrate by rf magnetron sputtering using a ceramic target ($In_2O_3:SnO_2$, 90:10wt.%). These films were annealed in $N_2$ and air atmosphere at $400^{\circ}C$ for 20min, 1hr, and 2hrs. ITO films deposited on the SLG show a high electrical resistivity and structural defect as compared with those deposited on the PD200 due to the Na ion from the SLG on diffuse to the ITO film by annealing. However these properties can be improved by introducing a barrier layer of $SiO_2$ or $Al_2O_3$ between ITO film and the SLG substrate. The characteristics of films were examined by the 4-point probe, FE-SEM, UV-VIS spectrometer, and X-ray diffraction. SIMS analysis confirmed that barrier layer inhibited Na ion diffusion from the SLG.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.322-327
• /
• 2012

Parallel-plate-type scanning sensors have been commercially used for X-ray imaging sensors. In this study, we manufactured the scan typed 1D X-ray image sensor that can be used to obtain scanning images, by using the plasma display panel (PDP) fabrication process. We fabricated drift and pixel electrodes in the glass chamber and injected Xe gas at atmospheric pressure. We evaluated the intensity of a pixel signal depending on the bias voltage on the drift electrode and investigated the characteristics of shielding effect on the single pixel using lead (Pb). The adsorption rate of X-ray photon is low (4%) on the soda lime glass (1.1mm) and the electrical signal detected on the X-ray sensor was increased in the high bias voltage. We acquired digital X-ray scanning image with our DAS (data acquisition system) and sensor scanning system.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.3 no.3
• /
• pp.1-15
• /
• 2008

The paper discusses application of soft OR methodologies, which have been developed for last decades centered in European OR communities, to strategy formation process. It is shown that there is strong similarity in understanding of strategy formation between descriptive school of strategy and the research trend of soft OR. The focus and philosophical background of cognitive school of strategy, in particular, share much in common with soft OR school. The analysis and overview of several soft OR methodologies are introduced. It is also proposed that SODA can be utilized more directly to the strategy formation process. However, it is also noted in this paper that the epistemological issues should be considered and resolved for fluent investigation of soft OR methodologies in relation with existing rich strategic research works, for soft OR adopts interpretative research methods while strategy research generally lies on positivistic approaches.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.362-368
• /
• 2005

The pH, alkalinity and calcium hardness could be adjusted by $CO_2$, $Ca(OH)_2$, and $Na_2CO_3$ addition in the water treatment process for corrosion protection of the water pipes. This research was performed to investigate the effect on the variation of water quality on the unit process by addition $CO_2$, $Ca(OH)_2$, and $Na_2CO_3$ in water treatment process. Carbon dioxide and lime were added before the coagulation basin and soda ash was added after the BAC process. pH and aklainity were increased at coagulation basin then after the water qualities had sustained similiarly to BAC process. There was no effect on turbidity and DOC removal efficiency during experimental period by addition\ $CO_2$, $Ca(OH)_2$, and $Na_2CO_3$ solution was added into clear well, the last process for optimum control of CCPP and is used mainly to control pH and alkalinity. In this research, average pH, alkalinity, and calcium hardness in treated water were 8.39, 61.4 mg/L as $CaCO_3$, 59.4 mg/L as $CaCO_3$, respectively and CCPP of treated water was higher than 29.5 mg/L to BAC process water, so adjusted water was expected to prevent internal corrosion of water pipe.

• Journal of the Korean Wood Science and Technology
• /
• v.7 no.2
• /
• pp.3-30
• /
• 1979

Larch ($\underline{Larix}$ $\underline{leptolepis}$ GORDON), one of the major afforestation species in Korea in view of its growing stock and rate of growth, is not favored as a raw material for pulp due to its low yield of pulp and difficulties with bleaching arising from the high content of extractives in wood, and the high heartwood ratio and the active phenolics, respectively. The purpose of this study is to investigate the characteristics of firstly pulping with various additives of cellulose protector for the yield of pulp, and secondly bleaching with oxygen for chlotination-alkali extraction of five stage-sequence to reduce chlorine compounds in bleaching effluents. The kraft cooking liquor for five age groups of larchwood was 18 percent active alkali with 25 percent sulfidity and 5 : 1 liquor-to-wood ratio, and each soda liquor for sap-and heart-wood of the 15-year-old larchwood was 18 percent alkali having one of the following cellulose protectors as the additive; magnesium sulfate ($MgSO_4$, 2.5%), zinc sulfate ($ZnSO_4$, 2.5%), aluminium sulfate ($Al_2(SO_4)_3$, 2.5%), potasium iodide (KI, 2.5%), hydroquinone (HQ, 2.5%), anthraquinone (AQ, 0.1%) and ethylene diamine (EDA, 2.5%). Then each anthraquinone-soda liquor for the determination of suitable cooking condition was the active alkali level of 15, 17 and 19 percent with 1.0, 0.5 and 0.1 percent anthraquinone, respectively. The cooking procedure for the pulps was scheduled to heat to 170$^{\circ}C$ in 90 minutes and to cook 90 minutes at the maximum temperature. The anthraquinone-soda pulps from both heartwood and sapwood of 15-year-old larchwood prepared with 0.5 percent anthraquinone and 18 percent active alkali were bleached in a four-stage sequency of OCED. (O: oxygen bleaching, D: chlorine dioxide bleaching and E: alkali extraction). In the first stage oxygen in atmospheric pressure was applied to a 30 percent consistency of pulp with 0.1 percent magnesium oxide (MgO) and 3, 6, and 9 percent sodium hydroxide on oven dry base, and the bleached results were compared pulps bleached under the conventional CEDED (C: chlorination). The results in the study were summarized as follows: 1. The screened yield of larch kraft pulp did not differ from particular ages to age group, but heartwood ratio, basic density, fiber length and water-extractives contents of wood and the tear factor of the pulp increased with increasing the tree age. The total yield of the pulp decreased. 2. The yield of soda pulp with various chemicals for cellulose protection of the 15-year-old larchwood increased slightly more than that of pure soda pulp and was slightly lower than that of kraft pulp. The influence of cellulose protectors was similar to the yield of pulps from both sapwood and heartwood. The effective protectors among seven additives were KI, $MgSO_4$ and AQ, for which the yields of screened pulp was as high as that of kraft pulp. Considering the additive level of protector, the AQ was the most effective in improving the yield and the quality of pulp. 3. When the amount of AQ increased in soda cooking, the yield and the quality of the pulp increased but rejects in total yield increased with decreasing the amount of active alkali from 19 to 15 percent. The best proportion of the AQ seemed to be 0.5 percent at 17 percent active alkali in anthraquinone-soda pulping. 4. On the bleaching of the AQ-soda pulp at 30 percent consistency with oxygen of atomospheric pressure in the first stage of the ODED sequence, the more caustic soda added, the brighter bleached pulp was obtained, but more lignin-selective bleaching reagent in proportion to the oxygen was necessary to maintain the increased yield with the addition of anthraquinone. 5. In conclusion, the suitable pulping condition for larchwood to improve the yield and quality of the chemical pulp to the level for kraft pulp from conventional process seemed to be. A) the selection of young larchwood to prevent decreasing in yield and quality due to the accumulation extractives in old wood, B) the application of 0.5 percent anthraquinone to the conventional soda cooking of 18 percent active alkali, and followed, C) the bleaching of oxygen in atmospheric pressure on high consistency (30%) with 0.1 percent magnesium oxide in the first stage of the ODED sequence to reduce the content of chlorine compounds in effluent.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.239-246
• /
• 2013

Principle of foamed glass manufacturing process first starts with putting vitreous material powder into a mold. After the foaming calcination, foamed body should be annealed after separation from the mold. For this reason, existing manufacturing process could not be a continuous type process. In this study, in order to develop a continuous production process of foamed glass, the possibility of new foam glass manufacturing process was investigated by foaming calcination of the compact body obtained from compression-molding of vitreous raw materials in stead of using a mold. Through the experimental results of the foaming calcination of the compact body with adding various foaming agents such as $Na_2CO_3$, $CaCO_3$ and petroleum coke, into hydrated soda-lime vitreous raw materials, it was shown that developing a continuous process without using any molds for manufacturing foamed glass would be possible.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.78-81
• /
• 2003

Polishing Processes are widely used in the glass, optical, die and semiconductor industry and are conventionally carried out using abrasive slurry and a polishing pad. But abrasive slurry process has a weak point that is high cost of handling of used slurry and hard controllability of slurry. Recently, some researches have attempted to solve these problems and one method is the development of a fixed abrasive pad. FAP has a couple of advantages including clean environment, lower CoC, easy controllability and higher form accuracy. But FAP also has a weak point that is need of dressing because of glazing and loading. The paper introduces the basic concept and fabrication technique of FAP using hydrophilic polymers with swelling characteristics in water and explains the self-conditioning phenomenon. Experimental results demonstrate to achieve nano surface roughness of soda lime glass for optical application

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.440-445
• /
• 1992

The major purpose here is to estimate the drying time required in the fish-drying process employed. The basic element of the prediction of the drying time is the model or the equation, which governs the change in weight. By an intuitive consideration on the mechanism of dehydration, a mathematical model of the fish-drying process is built, which is described by a system of linear differential equations. Further, a modified system of linear differential equations for a model of drying is also proposed for more accurate estimation. The parameter estimation of this system of equations provides the prediction of necessary drying time.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.779-782
• /
• 2012

$CuIn_{1-x}Ga_xSe_2$ (CIGS) thin films are grown on Mo/soda lime glass using a reactive sputtering process in which a Se cracker is used to deliver reactive Se molecules. The Cu and $(In_{0.7}Ga_{0.3})_2Se_3$ targets are simultaneously sputtered under the delivery of reactive Se. The effects of Se flux on film composition are investigated. The Cu/(In+Ga) composition ratio increases as the Se flux increases at a plasma power of less than 30 W for the Cu target. The (112) crystal orientation becomes dominant, and crystal grain size is larger with Se flux. The power conversion efficiency of a solar cell fabricated using an 800-nm CIGS film is 8.5%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.203-203
• /
• 2012

The SWCNTs network are formed on various plastic substrates such as poly(ethylene terephthalate) (PET), polyimide (PI) and soda lime glass using roll-to-roll printing and spray process. Selective patterning of carbon nanotubes film on transparent substrates was performed using a femtosecond laser. This process has many advantages because it is performed without chemicals and is easily applied to large-area patterning. It could also control the transparency and conductivity of CNT film by selective removal of CNTs. Furthermore, selective cutting of carbon nanotube using a femtosecond laser does not cause any phase change in the CNTs, as usually shown in focused ion beam irradiation of the CNTs. The patterned SWCNT films on transparent substrate can be used electrode layer for touch panels of flexible or flat panel display instead indium tin oxide (ITO) film.