• Journal of the Korean Vacuum Society
• /
• v.11 no.3
• /
• pp.141-150
• /
• 2002

Titanium oxide thin films were deposited by DC reactive magnetron sputtering(RMS) with Ar ion-beam assistance using end-Hall ion source at low oxygen partial pressure and long target-to-substrate distance. The optical and structural properties of deposited films were investigated by the measurement of measured transmittance and reflectance, atomic force microscope(AFM), and X-ray diffraction(XRD). The results show that the Ax ion-beam assisted RMS for titanium oxide thin films induces the higher packing density, lower absorption, and smoother surface than the conventional RMS, suggesting that it can be employed in deposition of optical dielectric coatings.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.1
• /
• pp.38-50
• /
• 1998

Laser cutting tests were conducted to investigate the laser cutting characteristics of solid woods such as 25mm-thick white oak(Quercus acutissima) and maple(Acer mono), and wood-based panels such as 15mm-thick medium density fiberboard and particleboard. Test variables were laser power, cutting speed, grain direction, and moisture content. Specific cutting energy was measured and the qualities of cut surface were estimated in constant laser power. Specific cutting energy of white oak was larger than that of maple, and specific cutting energy of medium density fiberboard was smaller than that of particleboard. For both white oak and maple, specific cutting energy of green wood was smaller than that of air-dried wood because weight loss of moisture evaporation in green wood was larger than that in air-dried wood. In laser-cut surface, wood cells were not deformed and damaged, but in circular saw-cut surface fibers were pushed out and cut, and wood cells were deformed severely. However, mechanical surface roughness of saw-cut surface was smoother than that of laser-cut surface because of the existence of undeformed cell cavity in laser-cut surface.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.2 s.95
• /
• pp.135-147
• /
• 2005

As automobile technology advances, a smoother ride with less noise is desired. In order to achieve these purposes, a study on the vibration and noise produced by a moving automobile was carried out and a model for tire vibration characteristics which influence the ride performance was developed. The model was verified through simulations and experiments. The developed model was then applied to a half car model and automobile vibrations were analyzed. The effects of tire design parameters on the automobile vibration energy were investigated. The results from laboratory and field tests confirm the validity of the analytical model. The 17-DOF half-car model was built to analyze automobile vibration. The characteristics of the nonlinear model for a shock absorber were applied to this model. The results from the present 17-DOF half car model incorporating the analytical tire model with tire design parameters, were compared with the 5-DOF half car model where the tire was modeled with linear springs. The results of the 17-DOF model are close to the experimental results. Using the 17-DOF model, the influence of tire design parameter were considered. According to the analysis results, the vibrations at seat/body/wheel were predicted by simulation and experiment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.250-253
• /
• 2002

The operation of surface and edge finishing is the last and essential process of parts machining, because a product is completed as an assembly. Therefore, the quality of the finished parts has a direct effect upon the performance of the product. Especially, the edge quality depending on the burr control process is very important. A number of deburring processes have been developed for macro burrs such as barreling, brushing, chemical methods, etc. However, micro burr removal when piercing a very thin plate is very difficult, because this badly deteriorates the surface quality of the processed part. When ultrasonic wave is propagated in liquids, it forms an infinitude of micro bubbles. These bubbles generate extremely strong force, which removes micro burrs. In ultrasonic micro deburring, the problem is that burrs are not removed completely, because only components of the explosive force directly act on the burrs, which is not enough. An attempt was made to remove the burrs using ultrasonic vibration in water with SiC as an abrasive agent. Because of the abrasive, smoother edges have been achieved. There are many control parameters in ultrasonic deburring such as abrasive size, ultrasonic frequency and amplitude, distance between tool and workpiece, tilt angle of workpiece etc. This study focuses on how distance and tilt angle influence deburring effect. A number of experiments for these parameters have been carried out, and then the effect of each parameter analyzed.

• Transactions of Materials Processing
• /
• v.18 no.6
• /
• pp.465-470
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. The effect of surface roughness of cylinder liner on the friction coefficient was analyzed. This study provided tribological data of hard and soft piston ring coatings against cylinder liner. The surface roughness does exert an influence on the average friction coefficient, with smoother surfaces generally yielding lower friction coefficients. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics such as, scratch depth, width, pile-up height and elastic modulus.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.84.1-84.1
• /
• 2011

Typical solid oxide fuel cells (SOFCs) have limited applications because they operate at high temperature due to low ionic conductivity of electrolyte. Thin film solid oxide fuel cell with yttria stabilized zirconia (YSZ) electrolyte is developed to decrease operating temperature. Pt/YSZ/Pt thin film SOFC was fabricated on anodic aluminum oxide (AAO). The crystalline structure of YSZ electrolyte by sputter is heavily depends on the roughness of porous Pt layer, which results in pinholes. To deposit YSZ electrolyte without pinholes and electrical shortage, it is necessary to deposit smoother and denser layer between Pt anode layer and YSZ layer by sputter. Atomic Layer Deposition (ALD) technique is used to deposit pre-YSZ layer, and it improved electrolyte quality. 300nm thick Bi-layered YSZ electrolyte was successfully deposited without electrical shortage.

• The Journal of Korea Robotics Society
• /
• v.13 no.1
• /
• pp.55-62
• /
• 2018

In this paper, a method for estimation of external force on an end-effector using joint torque sensor is proposed. The method is based on portion of measure torque caused by external force. Due to noise in the torque measurement data from the torque sensor, a recursive least-square estimation algorithm is used to ensure a smoother estimation of the external force data. However it is inevitable to create a delay for the sensor to detect the external force. In order to reduce the delay, modified recursive least-square is proposed. The performance of the proposed estimation method is evaluated in an experiment on a developed six-degree-of-freedom robot. By using NI DAQ device and Labview, the robot control, data acquisition and The experimental results output are processed in real time. By using proposed modified RLS, the delay to estimate the external force with the RLS is reduced by 54.9%. As an experimental result, the difference of the actual external force and the estimated external force is 4.11% with an included angle of $5.04^{\circ}$ while in dynamic state. This result shows that this method allows joint torque sensors to be used instead of commonly used external sensory system such as F/T sensors.

• Textile Coloration and Finishing
• /
• v.21 no.1
• /
• pp.21-29
• /
• 2009

In order to enhance the functionality of a cotton fabric actually used as a clothing material for patients, the fabrics were treated with a chitosan/nanosilver mixed solution. The nanosilver had excellent biocompatibility, provided expectation of an additional performance, did not harm human beings, and supplements chitosan, which was disadvantaged if used alone for fabric treatment. The nanosilver was mixed thereto and a treatment effect due to a mixing ratio was considered. This study was observed through mechanical properties and hand value which were the important function. The treatment of chitosan/nanosilver mixed solution gave a smoother surface than the treatment of chitosan alone. As a result of evaluation of the forms according to KES-FB system, Koshi was deduced, and both Numeri and Fukurami were increased. Thereby, the cotton fabric was a little smooth to provide elasticity, due to the treatment of chitosan/nanosilver mixed solution. THV of the treated fabrics calculated from this basis increased at all mixing ratio as compared with the untreated fabric. The fabrics treated with chitosan/nanosilver mixed solution were shown a better THV than the fabric treated with chitosan alone.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.1
• /
• pp.40-47
• /
• 2003

This paper discussed the assessment of hand of Tencel denim fabrics finished by enzymatic hydrolysis. The subjective hand and the preference of Tencel denim fabrics were evaluated using the developed scale. The factors affecting consumers taste for Tencel denim fabrics were analyzed by statistics using SAS program. Also, the effects of cellulase treatment on the properties of Tencel denim fabrics were evaluated by the subjective hand measurements. The results are as follows: As the weight loss increased. fabrics were evaluated as finer, smoother, softer, warmer, more refined (surface properties), more compact and weaker (durability), more flexible, flossier, lighter, softer, thinner (sense of weight), more elastic, and less wrinkly (shape recovery). Fabrics were evaluated to have the dry touch regardless to the rate of weight loss (moisture properties). Overall hand preference of Tencel denim fabrics was in the side of not preferred. Hand of Tencel fabrics seems not to appeal to Korean people. Color preferences were not significantly different among five groups. The correlations between subjective hand and preference showed that fine, smooth, flexible, warm, refined, loose, soft, dry touches were preferred in Tencel denim fabrics.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.757-767
• /
• 1996

Poly(alkyl acrylate-g-caprolactone) graft copolymers were prepared, and they were applied as compatibilizing agents for polycarbonate (PC) / poly(acrylonitrile-butadiene-styrene) (ABS) blends. The incompatible poly(alkyl acrylate) segment was incorporated into the graft copolymer in order to localize the copolymer at the PC/ABS interface. The blend containing 1 phr of the copolymer showed remarkable improvement in impact strength as well as in elongation at break. Impact improvement was more pronounced with a thinner test specimens of 1/8 inch thickness. Morphological study showed that the presence of the graft copolymer led to a smoother PC/ABS interface due to the interfacial enrichment of the graft copolymer.