• Journal of Korean Society on Water Environment
• /
• v.39 no.2
• /
• pp.131-141
• /
• 2023

In this study, the relationship between organic carbon distribution characteristics and decomposition rate classified according to the particle size and biological degradation characteristics in water was investigated for the Nam river and Geumho river. The average concentrations of TOC in the Nam river and Geumho river were 2.7±1.2 mg/L and 5.0±1.2 mg/L, respectively, but the composition ratios for each type of organic carbon were similar. An average value of 80.9% of TOC was present as DOC and 72.8% of DOC consisted of Refractory-DOC (RDOC). In addition, the change in the RDOC composition ratio according to temporal and spatial distribution was the smallest. There was no difference in the decomposition rate of organic carbon except for TOC by the site (p≥0.108, one-way ANOVA), and the decomposition rates of Labile-POC (LPOC) and LDOC were similar at 0.139±0.102 and 0.137±0.149 day^-1, respectively (p=0.110, paired t-test). The coefficient of variation (CV) of the decomposition rate of DOC (average 8.1%), which had the smallest composition ratio of organic carbon, was 1.1, showing the largest temporal variation. The TOC, POC, and DOC decomposition rates showed a significant correlation with the ratio of the initial concentration to the concentration after 25 days of decomposition (OC₂₅/OC₀) (r²=0.89~0.94, p<0.001), and the decomposition rates of LPOC and LDOC were significantly correlated with the ratio of the initial concentration to the concentration after 5 days of decomposition (LOC₅/LOC₀) (r²=0.67~0.75). This suggests that it is possible to estimate the decomposition rate through the concentration of each type of organic carbon.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.59 no.1
• /
• pp.55-64
• /
• 2023

Gas turbine engines are widely used as prime movers of generator and propulsion system in warships. This study addresses the problem of designing a DS-based PID controller for speed control of the LM-2500 gas turbine engine used for propulsion in warships. To this end, we first derive a dynamic model of the LM-2500 using actual sea trail data. Next, the PRC (process reaction curve) method is used to approximate the first-order plus time delay (FOPTD) model, and the DS-based PID controller design technique is proposed according to approximation of the time delay term. The proposed controller conducts set-point tracking simulation using MATLAB (2016b), and evaluates and compares the performance index with the existing control methods. As a result of simulation at each operating point, the proposed controller showed the smallest in %OS, which means that the rpm does not change rapidly. In addition, IAE and IAC were also the smallest, showing the best result in error performance and controller effort.

• The Bulletin of The Korean Astronomical Society
• /
• v.46 no.2
• /
• pp.65.1-65.1
• /
• 2021

The Donggungilgi (東宮日記) is the daily records of the Siganwon (侍講院), which was a royal office in the Joseon dynasty that took charge of the education for the crown prince who dwelled in the Donggung (East Palace). This literature contains records of meteorological and astronomical observations as well as educational matters. The Sohyeon-Donggungilgi (昭顯東宮日記) includes records from 1625 to 1645, when Prince Sohyeon, the first son of King Injo (仁祖), was the crown prince. We investigate the records of solar halo observations in the Sohyeon-Donggungilgi. For consistency, we restrict our investigation to the period before the second Manchu invasion of Korea (i.e., 1625 to 1635). We extract 2,684 records and classify them into ten events according to the terms in their descriptions. The largest and smallest number of observation records are for the Hun (暈) and Geuk (戟) events (1,794 and 7 records, respectively). To verify what each event represents in modern atmospheric terms, we refer to historical documents of the Seoungwanji (書雲觀志, Treaties on the Bureau of Astronomy) and Cheonmundaeseong (天文大成, Great Achievements in Astronomy). We also calculate the solar altitude based on the observation hour and compare the descriptions to compute simulations provided by Arbeitskreis Meteore e.V.. We find that the descriptions of the Hun, Junghun (重暈), Yi (珥), and Baekhonggwanil (白虹貫日) events indicate a 22˚ halo, 22˚ and 46˚ halos, a parhelion, and a parhelic circle, respectively, Alternatively, we estimate that the Gwan (冠), Dae (戴), Bae (背), Li (履), and Gyohun (交暈) events describe arcs tangent to a 22˚ or 46˚ halo such as a upper or lower tangent arc, a circumzenithal arc, or a parry arc. We suggest that further studies are required for the Geuk event because the descriptions of this event differ from both documents referred to this study. In the sense that the number of observation records of the Geuk event is the smallest, however, this event may describe a rare phenomenon. We believe that this work will contribute to the study of historical records of solar or lunar halos.

• Design & Manufacturing
• /
• v.17 no.2
• /
• pp.9-14
• /
• 2023

In this study, an experiment was conducted to confirm the applicability of the external shape control of the ultrasonic knife to the CFRTP material, which is the base material of thermoplastic. TC910 based on polyamide6 (PA6) was used as the material. The slope 와 and tool transfer speed of the material and tool were selected as process factors for processing, and the following results were obtained. Under all cutting conditions using an ultrasonic knife, friction heat caused by high-frequency vibration was issued at 150℃ at the contact part between the material and the knife during cutting. As a result of the cutting force analysis, the faster the transfer speed, the higher the cutting force as the angle of entry of the blade increased, and the size of the cutting force changed during cutting. As for the size of the burr in accordance with the transfer speed condition, the smallest burr occurred at 150mm/min in the side part, and the smallest burr occurred at 150mm/min and 200mm/min in the case of the outlet burr. The size of the burr according to the entry angle tended to decrease as the tool entry angle increased, and the side part tended to increase as the tool entry angle increased. As a result of the cutting surface analysis, it was confirmed that the base material was eluted under all conditions, and the faster the transfer speed, the lower the elution phenomenon of the base material. Based on the above results, cutting the CFRTP material with an ultrasonic knife is possible, but the effect on heat generation caused by friction needs to be minimized, and further research needs to be conducted on this.

• Korean Journal of Animal Reproduction
• /
• v.24 no.2
• /
• pp.209-216
• /
• 2000

This study was carried out to investigate the effects of breed, age of boar, season, parity and mating system on boar semen characteristics and fertilizing capacity. A total of 4181 sows and 199 boars of Durocs (D), Landraces (L), and Yorkshires (Y) were used for this experiment at Darby Artificicial Insemination Center from 1996 through 1999. Semen volume per ejaculate was largest in Landrace (266.8 $m\ell$), followed by Yorkshire, and was smallest in Duroc. Sperm motility did not show significant differences among the above breeds. Sperm concentration was lowest in Landrace (4.7$\times$10$^{9}$ sperm/$m\ell$) and was highest in Duroc (5.7$\times$10$^{9}$ sperm/$m\ell$). Semen volume per ejaculate according to the age of boars was largest at the age of 2 years, followed by the age of 4 and 3 years, and was smallest at the age of I year. Semen volume per ejaculate according to the season in boars was largest in winter (228.6 $m\ell$), followed by autumn and summer, and was smallest in spring. Sperm concentration was highest in spring (5.9$\times$10$^{9}$ sperm/$m\ell$), followed by summer and winter, and was lowest in autumn. The average litter weight at birth did not show any differences according to the mating type. But the number of pigs born alive per litter was largest (9.5 pigs) in the natural mating ＋ artificial insemination group, followed by the artificial insemination group (9.2 pigs), and was smallest (8.9 pigs) in the natural mating group (P＜0.01). The average litter weight at birth and number of pigs born alive per litter did not show any differences between the natural mating and artificial insemination. The L (♀)$\times$Y (♂) and L (♀)$\times$L (♂) matings show $\varepsilon$ d higher average litter weight at birth and number of pigs born alive per litter than the Y (♀) $\times$ Y (♂) and Y (♀) $\times$ L (♂) matings. The pigs in the 2~6th parities had higher average litter weight at birth and number of pigs born alive per litter than those in the 1 st and 7~9th parities.

• Journal of Mechanical Science and Technology
• /
• v.17 no.3
• /
• pp.336-342
• /
• 2003

Increasing demand on precision machining using computerized numerical control (CNC) machines have necessitated that the tool move not only with the smallest possible position error but also with smoothly varying feedrates in 3-dimensional (3D) space. This paper presents the simultaneous 3D machining process investigated using a retrofitted PC-NC milling machine. To achieve the simultaneous 3-axis motions, a new precision interpolation algorithm for 3D Non Uniform Rational B-Spline (NURBS) curve is proposed. With this accurate and efficient algorithm for the generation of complex 3D shapes, a real-time NURBS interpolator was developed using a PC and the simultaneous 3D machining was accomplished satisfactorily.

• Bulletin of the Korean Mathematical Society
• /
• v.37 no.4
• /
• pp.649-657
• /
• 2000

The 2-step competition graph of D has the same vertex set as D and an edge between vertices x and y if and only if there exist (x, z)-walk of length 2 and (y, z)-walk of length 2 for some vertex z in D. The 2-step competition number of a graph G is the smallest number k such that G together with k isolated vertices is the 2-step competition graph of an acyclic digraph. Cho, et al. showed that the 2-step competition number of a path of length at least two is two. In this paper, we characterize all the minimal acyclic digraphs whose 2-step competition graphs are paths of length n with two isolated vertices and construct all such digraphs.

• Journal of Microbiology and Biotechnology
• /
• v.3 no.2
• /
• pp.86-90
• /
• 1993

CMCase positive clones were screened from Cellulomonas sp. YE-5 and named pCE1, pCE2 and pCE3. Among the positive clones pCE1 was used for this study, because it has the smallest insert and the highest CMCase activity among the 3 clones, and its nucleotide sequence was determined. The CMCase gene in pCE1 was composed of 1071 bp of nucleotides coding 357 amino acids. Computer analysis showed that the pCE1 has 65% sequence homology with the endoglucanase from Cellulomonas fimi.

• Ocean Science Journal
• /
• v.43 no.4
• /
• pp.183-193
• /
• 2008

Oncaea venusta Philippi, 1843 has been known as having some different size groups, but recent genetic study for cyt b and ITS 1 (Elvers et al. 2006) suggests that these size groups can be considered as different species. Of these size groups, the largest O. venusta Philippi and the smallest O. venella Farran, 1929 were first described in Korean waters. The latter is easily distinguishable from the former in the following characteristics in addition to its small size: (1) length to width ratio of genital double somite of two genders smaller, and (2) female second pediger bearing inconspicuous dorso-posterior swelling. Oncaea venusta and O. venella co-occur in Korean waters during spring to fall, but their occurrence patterns seasonally differ: the former shows higher density in fall while the latter does in summer.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2003.10a
• /
• pp.27-31
• /
• 2003

It can be classified in various methods to get the geoidal heights. It can be achieved geometric geoidal heights if we do GPS surveying in leveling point. The aims of this paper are calculation of geometric geoidal heights using GPS/leveling data in study area and evaluation of the global and local geoid models in and around Korean peninsula. For this study, study area was selected in the leveling line from Kunsan to Chonju city and GPS surveying was accomplished in the leveling line. And, also spherical harmonic analysis was made on the three global geopotential models, OSU91A, EGM96, EGM96m under same condition and KOGD2002, Korean gravimetric geoid model was made in this study The results shows that EGM96m is the best model because the differences between geoidal heights of EGM96m and geometric geoidal heights of GPS/Leveling data appear the smallest value among them.