• 대한기계학회논문집B
• /
• 제31권9호
• /
• pp.790-798
• /
• 2007

An experimental study was performed to investigate the effects of mixing quality, inlet pressure, nozzle diameter on CO, NO emission and radiation characteristics in porous ceramic fiber radiant burners. Observations of combustion characteristics occurring inside the burner system which was insulated fiber mat, were investigated by measuring emission and radiation characteristics. Combustion was achieved at the firing rate of $88{\sim}99\;kcal/hr$, inlet pressure of $100{\sim}250mmH_2O$. The fiber burner exhibit significant both spectral intensity peaks in the bands at $2.5{\mu}m\;and\;4.0{\mu}m$ relatively. There is a small difference in the variable mixing tube. However spectral intensity increased with the firing rate. CO emissions were found to be strongly dependent on the operating conditions. There was a tendency that CO concentration increased as the firing rate increases. the reason for rise of CO concentration is that is becomes it the relatively rich condition. Relatively low NO emission was observed for the whole operating range. The NO concentration is maximal at the firing rate of approximately 2850 kcal/hr and an air ratio of about 1.

• 한국방재학회 논문집
• /
• 제8권4호
• /
• pp.39-45
• /
• 2008

본 연구는 면적 $0.293\;m^2{\sim}0.360\;m^2$의 소형표지판용 지주의 풍하중에 대한 구조적 안정성을 유지하면서도 작은 충돌에도 분리가 일어나도록 고안된 내경 6 mm의 D12 mm 중공형 인덴티드 볼트를 이용한 소형지주용 브레이크어웨이 단부장치의 구조적 안전성을 정적 전단 및 인장실험으로 입증하고 동적특성을 이해하는데 기본이 되는 인덴티드 볼트의 분리 파괴에너지를 펜듈럼 실험과 비선형 동적해석 프로그램인 LS-DYNA 프로그램을 이용하여 구하고 두 가지 방법을 비교한 것이다. 인덴티드 볼트 3개로 이루어진 단부장치는 풍하중 43.1 kg$\sim$51.2 kg를 충분히 지지할 수 있는 것으로 나타났으며 인덴티드 볼트 1개 당 파괴에너지는 펜듈럼 실험값이 163.3J, 시뮬레이션 값이 153J로 유사하게 계산되어 모델의 유효성이 확인되었다.

• 한국태양에너지학회 논문집
• /
• 제23권1호
• /
• pp.1-8
• /
• 2003

Various efforts to combine new high-tech materials with solar system have been progressed nowadays in order to improve the performance of the existing passive solar system. TIM(Transparent Insulation Material) replacing the conventional outer building envelope glazing as well as the wall is good example for this trend. TI integrated wall is a thermal mass wall with a special shaped TIM instead of using typical envelope materials The tested TIM type is a small(diameter 4mm and thickness 50mm) capillary tube of Okalux model and cement brick(density 1500kg/m3). The purpose of this study was to analyze the thermal performance through the actual measurements performed in a test cell. This study was carried out to justify the following issues. 1) the impact of Tl-wall over the temperature variations 2) the impact of mass wall surface absorptance over the transient thermal behavior and 3) the impact of thermal mass wall thickness over the temperature variations. Finally, as results indicated that the peak time of room temperature was shifted about one hour early when absorptance of thermal mass wall changed from 60% to 95% for the 190mm thickness thermal mass wall test case. the temperature difference of both surfaces of thermal mass wall surface showed about $23^{\circ}C$ during a day of March for the 380mm thickness thermal mass wall case. However, the thermal mass wall was over-heated by outside temperature and solar radiation in a day of May the temperature difference of both surfaces of thermal mass wall surface was indicated $10^{\circ}C$ and inside temperature was observed more than average 22C.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 추계학술대회
• /
• pp.478-481
• /
• 1997

A technique or the preparation of porous polyurethane vascular prostheses was investigated. Small-diameter vessels are not in general clinical use due to their limited long-term biocompatibility and low patency rates in experimental trial. These limits are mainly due to the failure of mechanical unction of the vascular grafts. This failure has been suggested to result partially from compliance mismatch. The long-term patency is considered to depend critically on the properties of the material and the fabrication process of the graft. So the control of pores is very important and main points to develop a available vascular grafts. Two-kind polymer sheets was compared. One was the porous PU-sheet made at room temperature by the solvent/non-solvent exchange. And the other was the porous PU-sheet which was fabricated by thermal phase transition and solvent-/non-solvent exchange using the thermal controller. The polymer sheets had a uniform pore size and pore occupation. According to the result of the above experiments, polyurethane solution was injected into a mold designed or U-type tube. The average pore size and pore occupation were easily changed by changing polyurethane concentration, freezing temperature, and methods. This technique can give a proper pore size ($10{\sim}45\;{\mu}m$) or tissue in growth, and suitable compliances or matching with arteries and veins. Besides, the fabrication of more complicated shaped vessels such as the U-type vascular grafts is easily controlled by using the fixed mold. this method might give a desired compliant graft or artificial implantation with the presently valid medical polymers.

• Applied Microscopy
• /
• 제36권4호
• /
• pp.259-269
• /
• 2006

산왕거미 (Araneus ventricosus) 혈구의 유형을 세포화학적 및 percoll 밀도구배를 이용한 물리화학적 특성에 따라 구분하고, 각각의 미세구조를 고배율의 전자현미경으로 비교 관찰하였다. 혈구는 세포질에 함유된 과립의 유무에 따라 과립혈구와 무과립혈구로 구분되었으며. 과립혈구는 과립의 특성에 따라 다시 산호성 과립혈구와 염기호성 과립혈구, 그리고 헤모시아닌 과립을 함유한 혈색소혈구의 세 가지 유형으로 세분되었다. 산호성 과립혈구는 전체 혈구유형중 약 5%정도를 차지하였으며, 염기호성 과립혈구는 산호성 과립혈구에 비해 과립의 크기가 크고 구형이었다. 한편 무과립혈구는 혈구중 가장 크기가 작은 투명혈구와 심관의 내강에 주로 분포하는 편도혈구, 그리고 탈피 시에만 출현하는 대형의 탈피혈구로 다시 세분되었다.

• 한국재료학회지
• /
• 제23권1호
• /
• pp.18-23
• /
• 2013

In this study, the effects of cryogenic treatment cycles on the residual stress and mechanical properties of 7075 aluminum alloy (Al7075) samples, in the form of a tube-shaped product with a diameter of 500 nm, were investigated. Samples were first subjected to solution treatment at $470^{\circ}C$, followed by cryogenic treatment and aging treatment. The residual stress and mechanical properties of the samples were systematically characterized. Residual stress was measured with a cutting method using strain gauges attached on the surface of the samples; in addition, tensile strength and Vickers hardness tests were performed. The detailed microstructure of the samples was investigated by transmission electron microscopy. Results showed that samples with 85 % relief in residual stress and 8% increase in tensile strength were achieved after undergoing three cycles of cryogenic treatments; this is in contrast to the samples processed by conventional solution treatment and natural aging (T4). The major reasons for the smaller residual stress and relatively high tensile strength for the samples fabricated by cryogenic treatment are the formation of very small-sized precipitates and the relaxation of residual stress during the low temperature process in uphill quenching. In addition, samples subjected to three cycles of cryogenic treatment demonstrated much lower residual stress than, and similar tensile strength compared to, those samples subjected to one cycle of cryogenic treatment or artificial aging treatment.

• Elastomers and Composites
• /
• 제53권3호
• /
• pp.158-167
• /
• 2018

In this study, in-situ trans-selective polymerization of isoprene was carried out using titanium-based Ziegler-Natta catalysts. The catalysts were prepared by high-energy ball milling. Individually Large-inner-diameter carbon nanotubes (CNTL), and hydroxylated carbon nanotubes (CNTOH), along with magnesium chloride ($MgCl_2$) were used as the carriers for the catalysts. The optimum ball-milling time for preparing the $CNT/MgCl_2/TiCl_4$ Ziegler-Natta catalysts was 4 h. The $CNTOH/MgCl_2/TiCl_4$ catalyst showed a higher efficiency than that of the $CNTL/MgCl_2/TiCl_4$ catalyst, based on the rate of polymerization. The effects of the CNT-filler type on the isoprene polymerization behaviors and polymer properties were investigated. The morphologies of the trans-1,4-polyisoprene (TPI)/CNT and TPI/CNTOH nanocomposites exhibited a tube-like shape, and the CNTL and CNTOH fillers were well dispersed in the TPI matrix. In addition, the thermal stability of TPI significantly increased upon the introduction of a small amount of both CNTL/CNTOH fillers (0.15 wt%), owing to the satisfactory dispersion of the CNTL/CNTOH in the TPI matrix.

• 화훼연구
• /
• 제18권4호
• /
• pp.291-294
• /
• 2010

접목선인장 신품종 '황운'은 해외 수출용 목적으로, 황색과 오렌지색을 가진 복색의 '황월' 품종을 모본으로 황색의 계통 '0111021'을 부본으로 교배하여 2008년에 개발되었다. 이 품종은 처음 기내에서 무병삼각주에 접목된 후 100 mL 시험관에 정식되어 6개월간 생육되었다. 2005년에 기외에서 접목한 후에 2008년까지 3회에 걸쳐 그 특성이 조사되었다. 구는 황색의 편원형이며, 몸체에 7~9개의 결각이 있으며, 갈색의 직립형 가시를 가지고 있다. 10개월간 재배되었을 때 구의 직경은 40.9 mm로 대조 품종 '후광'에 비해 구가 작고, 자구 착생수는 평균 22.3개로 '후광' 품종에 비해 우수하였다.

• Journal of Mechanical Science and Technology
• /
• 제18권9호
• /
• pp.1680-1688
• /
• 2004

The information indicating device plays an important part in the information times. Recently, the classical CRT (Cathod Ray Tube) display is getting transferred to the LCD (Liquid Crystal Display) one which is a kind of the FPDs (Flat Panel Displays). The OLED (Organic Light Emitting Diodes) display of the FPDs has many advantages for the low power consumption, the luminescence in itself, the light weight, the thin thickness, the wide view angle, the fast response and so on as compared with the LCD one. The OLED has lately attracted considerable attention as the next generation device for the information indicators. And also it has already been applied for the outside panel of a mobile phone, and its demand will be gradually increased in the various fields. It is manufactured by the vapor deposition method in the vacuum state, and the uniformity of thin film on the substrate depends on the temperature distribution in the point-cell source. This paper describes the basic concepts that are obtained to design the point-cell source using the computational temperature analysis. The grids are generated using the module of AUTOHEXA in the ICEM CFD program and the temperature distributions are numerically obtained using the STAR-CD program. The temperature profiles are calculated for four cases, i.e., the charge rate for the source in the crucible, the ratio of diameter to height of the crucible, the ratio of interval to height of the heating bands, and the geometry modification for the basic crucible. As a result, the blowout phenomenon can be shown when the charge rate for the source increases. The temperature variation in the radial direction is decreased as the ratio of diameter to height is decreased and it is suggested that the thin film thickness can be uniformed. In case of using one heating band, the blowout can be shown as the higher temperature distribution in the center part of the source, and the clogging can appear in the top end of the crucible in the lower temperature. The phenomena of both the blowout and the clogging in the modified crucible with the nozzle-diffuser can be prevented because the temperature in the upper part of the crucible is higher than that of other parts and the temperature variation in the radial direction becomes small.

• 대한의용생체공학회:의공학회지
• /
• 제20권1호
• /
• pp.107-113
• /
• 1999

본 연구의 목적은 작은 부위의 종양 또는 수술후 잔여종양을 검출할 수 있는 소형 고성능 영상용 감마프로브를 개발하는 것이다. 감마프로브의 검출기 시스템을 위해 위치민감형 광전자증배관(PSPMT)을 사용하였고, -1000V의 고전압을 공급하였다. 섬광체는 직영 7.62cm, 두께 9.5mm인 NaI(Tl)를 사용하였으며, 광학그리스를 이용하여 NaI(Tl)와 PSPMT를 접합시켰다. 조준기는 평형육각구멍조준기로써 직경 1.3mm, 격벽 두께 0.22mm, 그리고 길이 40mm이었다. 신호처리시스템은 위치신호처리와 트리거신호처리로 구분되며, 위치신호처리는 전단증폭기, 주증폭기를 거쳐 가산, 감산, 제산신호회로를 이용하여 얻었고, 트리거신호는 가산증폭기, 일정분획식별기 그리고 게이트 모듈을 이용하여 얻었다. 데이터 획득은 Gamma-PF 인터페이스 보드를 경우유하여 PIP 소프트웨어와 펜티엄 PC에 제어되었다. 영상연구를 위해 점선원을 이용하여 장균이도 영상과 슬릿마스크 영상을 얻었다. 그리고 조준기를 사용하여 두 개의 구멍팬텀 영상을 얻었다. 고유공간분해능은 3.97mm이었으며, 시스템 공간분해능은 5.97mm이었다. PSPMT를 이용하여 개발한 소형 감마프로브에 의해 획득된 팬텀영상은 좋은 영상질을 보여주었으며, 임상적용을 위해서는 영상특성의 최적화 연구가 계속되어야할 것으로 생각된다.