• 한국건축시공학회지
• /
• 제11권6호
• /
• pp.557-566
• /
• 2011

The surfactants facilitate the formation of foam bubbles under a proper condition and provide stability of foam bubbles by decreasing the surface tension of solutions and increasing the viscosity of foam surface. However, there have been almost no practical data of foam concrete in this regard so far. This study aims to understand the effects of foaming agents such as anionic synthetic surfactant and anionic natural material surfactant on the low density foamed concrete. From the experiment, the vegetable soap of anionic natural material surfactants showed a higher foaming rate, more open pores, slightly lower compressive strength, and a higher permeability coefficient compared to the vegetable soap of anionic synthetic surfactants. It is believed that the natural material surfactants make not only the surface tension of the solution low but also the viscosity of slurry high.

• 한국주조공학회지
• /
• 제14권5호
• /
• pp.438-446
• /
• 1994

The effect of various thermomechanical treatments on the structure and rheological behaviour of Al-6.2wt%Si alloy in its solidification range were investigated using a Searle type high temperature viscometer. During continuous cooling, the viscosity increases gradually with increasing fraction of solidified alloy, until a critical fraction of solidified alloy is reached above which the viscosity sharply increases. The viscosity of the slurry, at a given volume fraction wolid, decreased with increasing shear rate. The size and morphology of primary solid particles during stirring is influenced strongly by shear rates, cooling rates, volume fraction and stirring time of solid. Morphological changes during stirring as a function of solid volume fractions, shear rate and processing time were also reported. In this study, the size of primary solid particles in these alloys consistently increases and the it`s aspect ratio decrease with the increase in fraction solid and decrease in shear rate. Crystal morphology changes from rosette type to spheroid type with the increase in shear rate and solid fraction.

• KSBB Journal
• /
• 제14권1호
• /
• pp.114-118
• /
• 1999

본 연구에서는 미생물 담당의 일종인 커들린을 콘크리트 혼화제로 사용하기 위하여 시험공장 수준에서의 커들란 대량생산 공정을 확립하고, 생산한 다당의 물성과 특성을 조사하고 콘크리트와의 혼합에 의한 콘크리트 재료분리 억제제로서의 새로운 용도를 평가하였다. 커들란을 300 리터 발효조에서 고농도로 대량 생산하기 위하여 커다란 규모로 대량 생산 시 종종 제한요인이 되는 산소 전달속도를 높게 유지할 수 있는 최적 교반속도와 세포성장 단계와 커들란 생산 단계에서의 배양액 pH를 전이하는 방법을 적용 하였다 교반속도를 200 rpm으로 유지하여 pH를 7.0으로 조절하여 20시간 배양 후, 배양액 내 암모니움은 고갈되었고. 이때 세포농도는 9.8g/L에 달하였다. 질소원이 고갈되고 커들란이 생산되는 단계에서 발효액의 pH를 5.5로 전이하여 최종 65g/L의 커들란을 120 시간 안에 생산할 수 있었다. 커들란의 용해도는 pH 11.0 이하에서는 거의 불용임을 알 수 있었으며, pH가 증가함에 따라 점차로 증가하여 pH 13에서는 거의 다 녹았다. 커들란의 점도는 pH 12에서 가장 높았고 pH 13에서도 높은 점도를 나타내었다. 시멘트 현탁액의 pH가 약 13 정도임을 생각할 때 커들란을 혼화제로 콘크리트에 첨가할 경우 잘 용해되고 또한 콘크리트의 점도를 증진시킬 수 있을 것으로 판단된다. 커들란을 소량 첨가하였을 때에도 물이 slurry로부터 분리되었으나 커들란을 소량 첨가하였을 때에도 시멘트 slurry로부터 물이 분리되지 않고 균일한 흐름 경향을 보았다. 결론적으로, 본 연구자들은 조업이 간편한 회분식발효를 통하여 고능도로 거들란을 대량생산할 수 있었으며, 효율적이고 저렴한 분리공정을 개발하였다. 이렇게 제조한 커들란을 소량 콘크리트에 첨가하여 재료 분리 억제 효과가 우수하였는 바, 커들란의 산업적 생산에 커다란 가능성을 부여한다.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.164-170
• /
• 2002

Acrylate 수계 결합제를 사용한 알루미나 테이프 캐스팅용 슬러리의 완전분산을 위한 최적의 분산제와 분산제량을 결정하기 위해 침강실험, 분말 함유량 실험, 점도 및 zeta 전위 측정을 행하였다. 알루미나 슬러리의 완전분산은 분산제를 polycarboxylic acid로 했을 때 얻어졌으며, 최적의 첨가량은 알루미나 100에 대하여 0.23∼0.24g 이었다. 분말에 대한 분산제량이 증가할수록 분산은 잘 이루어졌으나, 일정량 이상이 첨가되면 분산제가 용매 안에 과잉으로 존재하여 분산을 저해하는 요인으로 작용하였다. 테이프 캐스팅용 슬러리는 100g의 알루미나 분말에 0.2g의 polycarboxylic acid를 첨가하였을 때 분산 및 테이프 특성이 가장 우수하였고, 이 때 혼합한 결합제는 acrylate였고, 가소제는 Benzoflex를 사용하였다. 이 때 슬러리 최적 점도는 약 570 cps였고, 테이프 내 알루미나 량은 57 vol%이었다.

• Advances in concrete construction
• /
• 제9권6호
• /
• pp.537-545
• /
• 2020

In order to reduce the usage of cement slurry in grouting engineering and consume the tunnel excavation waste soil, a new geopolymeric grouting material (GGM) was prepared by combine completely weathered granite (CWG) and blast-furnace slag (BFS), which can be applied to in-situ grouting treatment of completely weathered granite strata. The results showed CWG could participate in the geopolymerization process, and GGM slurry has the characteristics of short setting time, high flowability, low viscosity, high stone rate and high mechanical strength, and a design method of grouting pressure based on viscosity evolution was proposed. By adjusted the content of completely weathered granite and alkali activator concentration, the setting time of GGM were ranged from 5 to 30 minutes, the flowability was more than 23.5 cm, the stone rate was higher than 90%, the compressive strength of 28 days were 7.8-16.9 MPa, the porosity were below 30%. This provides a novel grouting treatment and utilizing excavated soil of tunnels in the similar strata.

• 한국재료학회지
• /
• 제34권1호
• /
• pp.27-33
• /
• 2024

Al₂O₃ has excellent sintering properties and is important in semiconductor manufacturing processes that require high-temperature resistance and chemical inertness in a plasma environment. In this study, a comprehensive analysis of the chemical characteristics, physical properties, crystal structure, and dispersion stability of three commercially available Al₂O₃ powders was conducted. The aim was to provide a technological foundation for selecting and utilizing appropriate Al₂O₃ powders in practical applications. All powders exhibited α-Al₂O₃ as the main phase, with the presence of beta-phase Na₂O-11Al₂O₃ as the secondary phase. The highest Na⁺ ion leaching was observed in the aqueous slurry state due to the presence of the secondary phase. Although the average particle size difference among the three powders was not significant, distinct differences in particle size distribution were observed. ALG-1SH showed a broad particle size distribution, P162 exhibited a bimodal distribution, and AES-11 displayed a uniform unimodal distribution. High-concentration Al₂O₃ slurries showed differences in viscosity due to ion release when no dispersant was added, affecting the electrical double-layer thickness. Polycarboxylate was found to effectively enhance the dispersion stability of all three powders. In the dispersion stability analysis, ALG-1SH exhibited the slowest sedimentation tendency, as evidenced by the low TSI value, while P162 showed faster precipitation, influenced by the particle size distribution.

• Korean Chemical Engineering Research
• /
• 제47권6호
• /
• pp.720-726
• /
• 2009

가압으로 운전되는 삼상슬러리 기포탑에서 기포 체류량과 압력강하를 목적함수로하여 기포탑의 설계 및 scale-up을 위한 수력학적 similarity를 고찰하였다. 또한, 본 연구에서 선택한 각 실험변수가 기포탑의 직경변화에 따라 기포탑 내 기포 체류량에 미치는 영향을 분석하였다. 슬러리 기포탑에서 기체체류량 및 압력강하의 결정에 영향을 미치는 주요 인자로써 기체유속($U_G$), 연속 슬러리 상의 점도(${\mu}_{SL,eff}$) 및 표면장력(${\rho}_{SL}$), 운전압력의 변화에 따라 변화하는 기체상의 밀도(${\rho}_G$)와 슬러리 밀도(${\rho}_{SL}$)의 차($\rho_{SL}$-${\rho}_G$), 기포탑 내부에서 단위길이 당 압력강하(${\Delta}P/L$), 기포탑의 직경(D) 그리고 기포탑에서 다상흐름에 작용하는 중력의 영향을 고려하기 위해 중력가속도(g) 등을 선정하였다. 선정된 7개의 슬러리 기포탑의 수력학적 특성에 영향을 미치는 파라메타들과 3개의 기본차원들로부터 차원해석에 의해 수력학적 특성을 지배하는 4개의 무차원 군을 도출하였다. 도출된 무차원 군인 레이놀즈 수, 프라우드 수 그리고 웨버 수 등이 기포탑에서 기포체류량에 미치는 영향을 검토하였다. 기포탑 내부에서의 압력강하와 기체 체류량 등을 무차원 군의 상관식으로부터 효과적으로 예측할 수 있었다. 본 연구의 결과는 가압슬러리 기포탑의 설계 및 scale-up 등에 매우 유용한 정보를 제공할 수 있을 것으로 사료된다.

• 한국건축시공학회지
• /
• 제12권1호
• /
• pp.22-30
• /
• 2012

Four types of foaming agents, including Alcohol Ethoxy Sulfate (AES), Alpha Olefin Sulfonate (AOS), Vegetable Soap (VS), and Fe-Protein (FP), are widely used in the construction field. These have different surface tensions and viscosities in water of the same concentration, affecting the flow speed of liquid, size and distribution of foam, and foam stability. However, there is a lack of data regarding the properties of foam concrete using various foam agents. The purpose of this study is to investigate influence of foaming agents on the properties of foamed concretes with various densities. We find that the foaming agent type has little effect on the density, compressive strength, and thermal conductivity of foam concrete, but considerably affects the unit weight of foam, flow and flexural strength of foamed concrete. While almost all properties of foam concrete are affected by density in fresh or hardened state, the potential energy changed by slurry density and the viscosity of foam are dominant factors in the flowability of foam slurry.

• 한국세라믹학회지
• /
• 제47권6호
• /
• pp.566-571
• /
• 2010

Dispersion behavior of the slurries consisted of bimodal-type AlN powders was examined in non-aqueous solvent system. Azotropic solvent system and copolymer acidic dispersant were applied to the slurries. Measurements of the sedimentation height and the viscosity of the each slurry, and the test of particle size distribution of the each powder sample were conducted as examinations for the dispersion behavior at the various dispersant contents. The bimodal-type particle size distribution was continued after addition of the dispersant and small particle portions were increased as the dispersant content increases. The density of the green sheet was also increased as the dispersant content increases and a green density of $2.114\;g/cm^3$ was obtained at the sample prepared from 2.4 wt% dispersant content. The increase of large particle portions resulted in the surface defects of the green sheets.

• 한국전기전자재료학회논문지
• /
• 제17권10호
• /
• pp.1041-1048
• /
• 2004

Chemical mechanical polishing (CMP) process was studied in terms of tribology in this paper. CMP performed by the down force and the relative motion of pad and wafer with slurry is typically tribological system composed of friction, wear and lubrication. The piezoelectric quartz sensor for friction force measurement was installed and the friction force was detected during CMP process. Various friction signals were attained and analyzed with the kind of pad, abrasive and abrasive concentration. As a result of experiment, the lubrication regime is classified with ηv/p(η, v and p; the viscosity, relative velocity and pressure). The characteristics of friction and material removal mechanism is also different as a function of the kind of abrasive and the abrasive concentration in slurry. Especially, the material removal per unit distance is directly proportional to the friction force and the non~uniformity has relation to the coefficient of friction.