• 한국안전학회지
• /
• 제28권2호
• /
• pp.14-20
• /
• 2013

All most of floors can become less slip resistant with wear. The deterioration of slip resistance can often occur rapidly. So relatively new products can become hazardous within a short period of time. The main objective of this study was the comparison of slip resistance variations caused by traffic wear and accelerative wear. The second objective was to ascertain the effect of wear, and to find out the causes of slip resistance change. Although statistical differences were observed between results of traffic wear and accelerative wear, the trend of the variations of slip resistance caused by traffic wear and accelerative wear was very similar. The measured slip resistance of tested floor changed up to 29%(and 26.5%) after 100,000 steps(and 750 cycles). As the traffic wear and accelerative wear were progressed, the surface roughness of the tested floor became smoother, and so the floor became more slippery under the wet condition. The abraded(worn out) floor surface tended to become hydrophilic surface, while the new floor surface tended to show hydrophobic nature. This phenomenon would change the wettability of floor surface, and the wettability would affect the variation of slip resistance.

• 한국안전학회지
• /
• 제27권5호
• /
• pp.185-189
• /
• 2012

While there is no standards on slip risk for contaminants on surface, glycerol is described in standard contaminant for measuring coefficient of friction(COF) and slip resistance such as ISO 13287. But that is just used to measure the slip resistance of surface materials and shoes not to evaluate the contaminant materials. Therefore the objective of this study was to find out the relationship between standard contaminant and the contaminants used usually at the workplaces. For this, some measurement criteria were acquired from the analysis based on biomechanics and kinetics of human gait during slips. The slip resistance according to viscosity of the contaminants was measured applying the criteria and slip probability was determined by the gait analysis. Some factors which should be considered when measuring the slip resistance were identified. The velocity, acceleration, contact time and contact pressure should be 1 m/sec, 10 $m/sec^2$, 350 kPa and less than 0.5sec respectively. The variation of viscosity according to temperature for working oils was different from that of standard contaminant. The static coefficient of friction (SCOF) of working oils was almost 0.5 times as large as the SCOF of standard contaminant. So it was assumed to be difficult to compare the contaminants at the workplaces with the glycerol as a standard contaminant for estimating the slip risk.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.224-226
• /
• 1995

This paper presents an algorithm that the gain of the slip calculator is correctly adjusted for the variation of the rotor resistance. In the indirect field oriented controller, if the gain (rotor resistance) of the slip calculator is set the incorrect value, the torque and the flux are not properly controlled. Using of the two torque angles (i.e. stationary torque angle and rotating torque angle), we estimate the rotor resistance, and then adjust the gain of the slip calculator for the variation of the rotor resistance. It has been realized to confirm the validity of the proposed algorithm by the simulation results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.12-14
• /
• 1996

In this paper, the simulation of the effects of variation of rotor resistance of induction motor for the performance of vector control is presented. Especially, this paper considered the effects as a difference variation of the rotor resistance between slip calculator and induction motor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.65-68
• /
• 2001

In the vector control methods of induction motor, the stator current is divided into the flux and torque component current. By controlling these components respectively, the methods control independently flux and torque as in the DC motor and improve the control effects. To apply the vector control methods, the position of the rotor current is identified. The indirect vector control use the parameters of the machine to identify the position of rotor flux. But due to the temperature rise during machine operation, the variation of rotor resistance degrades the vector control. To solve the problem, the q-axis is aligned to reference frame without phase difference by comparing the real flux component with the reference flux component. Then to compensate the slip, PI controller is used. The proposed method keeps a constant slip by compensating the gain of direct slip frequency when the rotor resistance of induction motor varies. To prove the validations of the proposed algorithm in the paper, computer simulations is executed.

• 한국정보통신학회논문지
• /
• 제4권2호
• /
• pp.487-492
• /
• 2000

본 논문은 유도전동기 간접 벡터 제어시 회전자 시정수 변동에 대한 슬립보상 방법을 제안하였다. 회전자 시정수가 변동하면 고정자 전류의 자속 및 토크 성분의 상호 간섭이 발생하여 벡터제어가 불가능하고 성능이 저하하게 된다. 이를 해결하기 위하여 본 논문에서는 실제 자속 성분과 기준 자속 성분을 비교하여 위상차 없이 자속 성분을 기준 좌표의 q축에 일치시키고 PI 제어기를 이용하여 슬립을 보상하는 방법을 제시하였다. 제안된 방법을 이용하면 유도전동기의 회전자 저항 변동시 q축 자속 성분이 0이 되어 적정 슬립이 유지되고 정확한 벡터제어가 실현된다. 제안된 알고리즘의 타당성을 컴퓨터 시뮬레이션과 실험을 통하여 검증하였다.

• 한국안전학회지
• /
• 제9권4호
• /
• pp.42-48
• /
• 1994

A rotor flux error-based approach for correcting the rotor time constant estimation used in the slip frequency calculator of indirect field oriented controller is presented in this paper. The controller was derived from the d-q induction machine model. Slip frequency gain is dependent on the machine parameter errors. And parameter errors result in rotor flux error. Thus, estimated rotor flux is compared to commanded rotor flux. The error between them is used for the estimation of rotor time constant. Simulation results which demonstrate the performance of this approach are presented.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.65-68
• /
• 2001

In the vector control methods of induction motor, the stator current is divided into the flux and torque component current. By controlling these components respectively, the methods control independently flux and torque as in the DC motor and improve the control effects. To apply the vector control methods, the position of the rotor current is identified. The indirect vector control use the parameters of the machine to identify the position of rotor flux. But due to the temperature rise during machine operation, the variation of rotor resistance degrades the vector control. To solve the problem, the q-axis is aligned to reference frame without phase difference by comparing the real flux component with the reference flux component. Then to compensate the slip, PI controller is used. The proposed method keeps a constant slip by compensating the gain of direct slip frequency when the rotor resistance of induction motor varies. To prove the validations of the proposed algorithm in the paper, computer simulations is executed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1215-1217
• /
• 1992

This Paper described the hish performance position control for elevator using induction motor and driver. In this paper, the suitable Motor specifications for elevator drive are briefly discussed and high accuracy position control for both kinds of control method is analysed considering the parameter variation in the primary and secondary resistances. Since the pre-identified values of the motor constants are used to determine the control inputs, the performance degradation is caused by the parameter variation such as in the motor resistance. Particularly, the value of secondary resistance is considered significant because the control gain to determine the slip frequency is heavily dependent on that. The new proposed method uses on special small input signal for the parameter indentification and is expected to have the high accuracy position.

• 한국전산구조공학회논문집
• /
• 제16권1호
• /
• pp.53-58
• /
• 2003

탄소섬유쉬트는 경량, 고강도, 우수한 내식성, 그리고 간편한 시공성 때문에 많은 종류의 철근콘크리트 부재의 보강에 사용되고 있다. 그러나 탄소섬유쉬트에 의해 보강된 철근콘크리트 부재의 파괴거동은 탄소섬유쉬트와 콘크리트 표면의 부착특성에 따라 크게 달라진다. 본 연구에서는 탄소섬유쉬트와 콘크리트 사이의 경계면에 링크요소를 이용함으로써 탄소섬유쉬트와 콘크리트 사이의 부착거동의 변화를 고려한 부착응력-미끄럼 모델을 제안하였다. 또한 이 방법의 유효성을 알아보기 위하여 탄소섬유쉬트로 보강된 철근콘크리트 보의 파괴거동에 대한 해석을 실시하여 실험결과와 비교하였다. 그 결과 본 연구에서 제안된 모델을 이용한 해석결과는 실험결과와 비교적 잘 일치함을 알 수 있었다.