• 터널과지하공간
• /
• 제15권4호
• /
• pp.288-295
• /
• 2005

암반은 여러 가지 지질학적 요인에 기인한 역학적 결함을 많이 포함하고 있기 때문에 이방성 거동을 보이는 경우가 대부분이다. 그러므로 안정한 암반구조물이나 암반기초의 설계를 위해서는 이방성 암반에서 응력분포의 특성을 이해하는 것이 매우 중요하다. 이 연구에서는 반무한 평면이방성 지반의 표면에 선하중이 작용할 때 지반에 야기되는 탄성응력 분포의 특성을 고찰하였다. 절리의 강성과 절리의 간격, 경사각이 응력분포 형태에 미치는 영향이 검토되었다. 절리면의 미끄러짐 조건으로 Mohr-Coulomb 식을 가정할 경우, 절리면을 통한 미끄러짐이 발생할 수 있는 영역에 대한 고찰도 수행되었다.

• Journal of Mechanical Science and Technology
• /
• 제14권2호
• /
• pp.226-235
• /
• 2000

The performance prediction of an airfoil fan using a commerical code, STAR/CD, is verified by comparing the calculated results with measured performance data and velocity fields of an airfoil fan. The effects of inlet tip clearance on performance are investigated. The calculations overestimate the pressure rise performance by about 10-25 percent. However, the performance reduction due to tip clearance is well predicted by numerical simulations. Main source of performance decrease is not only the slip factor but also impeller efficiency. The reduction in performance is 12-16 percent for 1 percent gap of the diameter. The calculated reductions in impeller efficiency and slip factor are also linearly proportional to the gap size. The span-wise distributions of phase averaged velocity and pressure at the impeller exit are strongly influenced by the radial gap size. The radial component of velocity and the flow angle increase over the passsage as the gap increases. The slip factor decreases and the loss increases with the gap size. The high velocity of leakage jet affects the impeller inlet and passage flows. With a larger clearance, the main stream moves to the impeller hub side and high loss region extends from the shroud to the hub.

• 대한기계학회논문집A
• /
• 제28권8호
• /
• pp.1203-1211
• /
• 2004

A traction control systems (TCSs) composed of either a wheel slip controller or a throttle valve controller or an integrated controller of both systems are proposed in this study. To validatethe dynamic characteristics of a vehicle and TCS, a full car model that can simulate the responses of both front wheel drive (2WD) and four wheel drive (4WD) vehicle is also developed. The wheel slip controller uses a sliding mode control scheme and the throttle valve is controlled by a PID controller. The results shows that tHe brake TCS and the engine TCS achieve rapid acceleration, and reduce slip angle on slippery road. When a vehicle is cornering and accelerating maneuver with the brake or engine TCS, understeer or oversteer occur, depending on the driving conditions. The integrated TCS prevents most of these problems and improves the stability and controllability of the vehicle.

• 한국가시화정보학회지
• /
• 제8권4호
• /
• pp.13-18
• /
• 2010

This paper presents an experimental study on the performance of a micro-mixer using AC electro-osmotic flow. The microchannel is made of PDMS for the side and top walls and glass patterned with ITO for the bottom wall. We first investigated the effect of the applied potential as well as the frequency on the slip velocity. We have found that the slip velocity is roughly proportional to the applied voltage in line with the Helmholtz-Smoluchowski equation and there is an optimum frequency at which the slip velocity becomes maximized. To find the optimum parameters for mixing device we tested our device for various design parameters. It turned out that the best mixing effect is obtained approximately when the electrode angle is $30^{\circ}$, electrode width $200\;{\mu}m$, and the frequency of power supply 700 Hz.

• Elastomers and Composites
• /
• 제49권3호
• /
• pp.191-198
• /
• 2014

산성기를 도입한 폴리우레탄에 나노산화아연을 첨가하여 열가소성 폴리우레탄 탄성체를 합성하였으며, 합성된 폴리우레탄 탄성체의 기계적물성, 열적특성, 접촉각, 그립특성을 평가하였다. 그리고 산화아연의 함량과 입자 크기가 폴리우레탄 탄성체에 미치는 영향에 대해서 연구하였다. 나노산화아연을 도입한 경우 이온결합이 형성되어 산성기에 의한 수소결합과 동시에 작용하기 때문에 인장강도, 마모 등 기계적 물성 및 그립특성이 향상되는 것이 확인되었다. 폴리우레탄내의 산화아연 함량에 따른 물성평가 결과 나노산화아연 함량이 증가할수록 이온결합 도입에 의한 친수성이 커져서 wet slip이 지속적으로 상승되었으며, 기계적 물성은 산화아연에 의한 이온화율 50%까지 향상되다가 그 이후에는 감소되는 현상을 나타내었다.

• 한국정밀공학회지
• /
• 제23권2호
• /
• pp.104-112
• /
• 2006

The influence of tire belt angle on the Plysteer Residual Aligning Torque(PRAT) and the cornering stiffness by the FEM has been studied. The PRAT is a performance factor of the tire about vehicle pull, and the cornering stiffness has relation to vehicle steering response of outdoor test. To validate FE model for analysis, simulation data for both the static stiffness(vertical, lateral) and the PRAT have been compared with the experimental data. In addition to the characteristics of the PRAT and the cornering stiffness due to the tire belt angle, rolling and cornering contact characteristics have been studied. The tendency of the PRAT and the cornering stiffness due to the belt angle can be used as a guide line for the tire design in relation to vehicle pull and vehicle steering response.

• 터널과지하공간
• /
• 제30권4호
• /
• pp.404-416
• /
• 2020

2차원 응력조건에서 V형 암석노치의 파괴하중을 계산하는 해석적 절차를 slip-line 소성해석법 기반으로 개발하였다. 노치 주변의 암석이 소성상태에 있을 때 slip-line 중 하나인 α선이 암석 노치 면과 노치 외부 수평면을 연결한다는 사실과 α선을 따라서 변하지 않는 불변량이 존재한다는 이론적 사실이 해석적 절차 개발과정에서 핵심 아이디어로 활용되었다. 암석 노치 외부 수평면의 응력 경계조건을 알고 있으므로 불변량 방정식을 풀면 암석 노치 면에 작용하는 수직응력과 전단응력을 계산하는 것이 가능해진다. 노치 면에 작용하는 응력성분 값을 이용하여 쐐기에 의해 노치에 가해지는 파괴하중을 계산하였다. 개발된 해석적 절차를 적용하여 암석 노치파괴 해석을 수행하였다. 암석 노치의 파괴하중은 노치의 각도 및 노치 면의 마찰이 증가함에 따라 지수함수적 비선형성을 가지고 증가하는 특성이 있음을 해석결과는 보여주었다. 이 연구에서 개발한 해석적 절차는 쐐기형 노치 형성을 통한 암석균열 개시조건 연구, 암반 기초 지지력 계산, 암반사면 및 원형터널의 안전성 해석 등에 응용될 수 있을 것으로 기대된다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.116-122
• /
• 2002

It is addressed that the turbulent broadband sound power from a sirocco fan can be modeled by the trailing edge noise. The trailing edge noise is usually influenced by inflow turbulenca separation, and boundary layer thickness on the blade. The design parameters such as solidity (c/s) and stagger angle are specified to predict performance and noise level because the separation and slip velocity are strongly affected by them along with the flow coefficient. This paper reports the effects of the stagger angle upon the trailing edge noise for various trailing edge shapes. It is believed that the serrated trailing edge provides break-up mechanism for organized convecting vortices, thereby reduce the overall noise level for every case of stagger angle.

• 한국유체기계학회 논문집
• /
• 제6권3호
• /
• pp.7-14
• /
• 2003

It is addressed that the turbulent broadband sound power from a sirocco fan can be modeled by the trailing edge noise. The trailing edge noise is usually influenced by inflow turbulence, separation, and boundary layer thickness on the blade. The design parameters such as solidity (c/s) and stagger angle are specified to predict performance and noise level because the separation and slip velocity are strongly affected by them along with the flow coefficient. This paper reports the effects of the stagger angle upon the trailing edge noise for various trailing edge shapes. It is believed that the serrated trailing edge provides break-up mechanism for organized convecting vortices, thereby reduce the overall noise level for every case of stagger angle.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.79-82
• /
• 2007

The aerodynamic coefficients of Apollo capsule are calculated using a DSMC solver, SMILE, and the results agree very well with the data predicted by NASA. The aerodynamic characteristics of an orbital block which operates at high altitudes in the free molecule regime are also predicted. For the nominal flow conditions, the predicted aerodynamic force is very small since the dynamic pressure is extremely low. And the additional aerodynamic coefficients for the analysis of the attitude control are presented as the angle of attack and the side slip angle vary from $+45^{\circ}\;to\;-45^{\circ}$ of the nominal angle.