• Steel and Composite Structures
• /
• v.7 no.4
• /
• pp.303-320
• /
• 2007

The objective of this study is to clarify the structural features of members consisting of connection, as a series of the previous study on the CFT column-to-beam tensile connection with combined cross diaphragm. This connection has the merits that the stress is distributed evenly on the beam flange and the diaphragm and the stress concentration is reduced, by improving the stress transfer route and restraining abrupt deformation of diaphragm. The finite element analysis was performed to find out the stress transfer through sleeve which is an important member of the connection with combined cross diaphragm. The length and thickness of sleeve were used as variables for the analysis. As the analysis results, the length and thickness of sleeve didn't influence on the capacity of the connection and played a role of a medium to transfer the stress from the diaphragm to the filled concrete. It is proposed that the appropriate length of sleeve be the same value as the diameter of sleeve and the appropriate ratio of sleeve diameter to sleeve thickness be 20. Two equations for evaluation of the load-carrying capacity of the connection were also proposed through the modification of the evaluation equation suggested in the previous study.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.6
• /
• pp.1-5
• /
• 2008

As bare Fiber Bragg Grating (FBG) sensors are very fragile, bare FBG without encapsulation is not properly applied in practical infrastructures directly due to the harsh environment in practical engineering. Steel sleeve packaged FBG strain sensor is widely used in civil engineering. Since FBG senses both strain and temperature simultaneously, for accurate measurement of strain, temperature compensation for FBG strain sensors is indispensable. In this paper, based on the FBG's strain and temperature sensing principles, the temperature compensation techniques for steel sleeve packaged FBG sensors are brought forward. And the experiment of concrete early-age shrinkage monitoring by dual FBG sensors is carried out to test the feasibility of the temperature compensation technique.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.11
• /
• pp.1009-1014
• /
• 2007

A detailed study on aged sleeves for old transmission lines was carried out to clarify the deterioration of sleeves and the condition of installation. A lot of removed aged sleeves from transmission lines were investigated. Many biased installed cases and corrosion of steel sleeve part were found. These defects can cause a serious accident such as blackout during operating. The temperature distribution within sleeve of ACSR conductor was precisely measured and examined, conducted as part of series of studies on large currents in transmission lines. According to measurements of the conductor temperature near a joint(sleeve and clamp), the electrical resistance of joint is lower than that of the same length conductor. The detailed results were presented in the text.

• The Research Journal of the Costume Culture
• /
• v.14 no.3 s.62
• /
• pp.404-417
• /
• 2006

The purpose of this thesis, therefore, is to examine the shaping methods and the knitting drafts of sleeve cap in the knitwears which are currently used by the manufacturers; to study the curve forms of sleeves in knitwears by analyzing synthetically the results of investigating the problems of knit wear sleeves; to present the most suitable sleeve cap for the knitwears. As the studying methods, I collected the basic data from the working-level persons of knit wear manufacturers, examined the knitting draft in the knitwears, and from that, made three kinds of comparative experimental garments and one kind of research experimental one as 10G and 16G. In doing so, I showed the sleeve cap suitable for the knitwears with plain stitch after operating sensual evaluation with Liker's 5-point rating measure. The analysis of data was handled with statistics by using SPSS Ver. 12.0; the method of statistics was executed by Frequency Analysis, Trust Analysis, one-way ANOVA, and Duncan test according to each topic of the research. As the result of the sensual evaluation of the experimental garments produced from the study, the research experimental garment looks better than the comparative experimental one in both 10G and l6G; has less extra folds around the front part of sleeve cap; looks more natural in sleeve caps of the body part and of a sleeve. From this, I am able to figure out that the research experimental garment looks better than the comparative experimental one produced by knit wear manufacturers. In addition, I can come to know that the different knitting of the front line and the back one of armhole in the knitwears has a favorable impact on improving the appearance of a sleeve.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.2
• /
• pp.67-73
• /
• 2011

This study aims to develop an economical precast hollow concrete column with high constructability which consists of only splice sleeve and general reinforcing bar without using PC tendons in order to reduce the construction period and cost. With this purpose, this study performed the finite element analysis and tension test by using some variables such as length of sleeve, diameter of rebar and curing method for suggesting a grouting type splice sleeve which is a new type joint rebar and developing an optimized splice sleeve. As a result, the analysis on the tension performance of splice sleeve did not show any destruction caused by pull-out in reinforcing bar but it only occurred destruction of tension bar or bolt shear rupture from the mechanical defect of sleeve. Therefore, the experiment showed high performance in tension of the suggested splice sleeve and verified the application of precast hollow concrete column.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.19 no.5
• /
• pp.826-841
• /
• 1995

This study is concerned with the functional utility of movement in sleeve from an ergonomic viewpoint. Experiments were carried out which include 43 upper extremity segments, 21 motions and 35 female subjects. The major conclusions of the study are. 1. The expansion rate of upper extremity was higher in length than in circumference mesurements. The amounts of expansion were, especially high (more than 60mm) for inner arm length, axillary arm circumference, and outer arm length. Therefore, a lot of ease is necessary for these parts. On the other hand, armhole circumference, forearm circumference, and wrist circumference had low rates of expansion. The sleeve cap length was also contracted in all motions. 2. The expansion rate and the range of expansion and contraction were higher in the upper arm than in the forearm. The main points of expansion were the axillary and elbow parts. The segment of maximum expansi (rate of 44.8%) was Iii of axillary parts. As the body surface expands mainly in some segments, it is desirable to allow ease to the main segments of expansion. 3. In a basic sleeve, necessary ease was lacking in the measurements for outer arm length and axillary arm circumference, while it was too large in armhole circumference, forearm circumference, wrist circumference, and sleeve cap length. Therefore, a basic sleeve is inadequate as a functional sleeve for hard work in point of functional utility of movement. Wider application of these findings would lead to an improvement in the comfort of workers.

• Fashion & Textile Research Journal
• /
• v.12 no.5
• /
• pp.619-625
• /
• 2010

The purpose of this research is to analyze the shapes of blouse with above-elbow sleeves according to arm movements. The shapes include five types of the arm movement(basic posture, reach forward 45, 90, and reach lateral 45, 90) in the stand-posture, which were made by different adaptability of clothes. Experiments were conducted to figure out the dressed shape through 3-D measurement Vivid 910, and also to investigate the area of the shape of sleeves on the section map and the diagonal length of the block made by the basic section line in lateral part of sleeve with Rapid Form 2004, a software for 3-D shape analysis. The Data were analyzed by factor analysis, Anova, Duncan test, t-test. The results of this study were as follows: First, the area of sleeve was briefed 3 factor; front, center, back in sleeve. Second, there were different effect of arm movement, section level and part of shapes in the area of sleeve. Third, the diagonal length was briefed 4 factor; back, back-center, front-center, front. Forth, after t-test, there were statistically significant between the reach forward and lateral and between the angles of arm reach.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.1036-1041
• /
• 2008

According to previous report, aged sleeves of old transmission line showed several defaulted installation patterns, which was biased or corrosive-fractured of steel sleeve installed cases. These defects can cause serious accidents such as rapid increasing of sag or falling out of overhead conductor from sleeves. Consequently, the defects lead to the major power outage. Corrosion of steel sleeve is a typical defect by aging of sleeves. And it occupied almost 25 percent of investigated aged sleeves. This paper studied thermal properties and tension for ACSR conductor in case of fractured steel sleeve model by corrosion. The temperature distribution within overhead conductor has a specific gradient. Thermal properties of splice connectors(sleeve and clamp) showed normal behavior. However, mechanical properties were worse than normal sleeves. The detailed results were presented in the text.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.3
• /
• pp.500-510
• /
• 2009

The purpose of this study was to examine the effects of facing plan on store image and preference of young casual fashion store. The subjects were 545 male and female university students in Chungnam province. The measuring instruments were 7 stimuli manipulated by facing plan, an important VMD element, and self-administrated questionnaire consisted of store image, store preference and subject's demographic characteristics. The data were analyzed by t-test, ANOVA and Duncan's multiple range test, using SPSS program. The results were as follows. First, facing type significantly affected consumer' store image; folded type had more neat and elegant image than other facing types, and face out type had most comfort image, whereas sleeve out type had discomfort image. Second, arrangement of facing types also affected store image; style arrangement had more sophisticated image than color arrangement in sleeve out type, and vertical and horizontal arrangement had more neat, sophisticated, attractive and comfort image than separate arrangement in folded type. Third, facing type affected store preference; folded type showed higher store preference than sleeve out type. Forth, arrangement of folded type affected store preference; vertical and horizontal arrangement showed higher store preference than separate arrangement. Fifth, store image and preference were different by subject's sex; male subjects perceived style arrangement as more elegant, characteristic and attractive image, and showed higher store preference than female subjects on separate arrangement of folded type.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1209-1210
• /
• 2008

According to previous report, aged sleeves for old transmission lines have variable defects such as biased installed case or corrosion of steel sleeve. Biased installed sleeve occupied 20 percent among the investigated aged sleeves. This defect must cause local heating of splice connector and limit power transmission capacity. It even inspire falling out of overhead conductor from sleeves. This paper studies thermal properties and tension for ACSR conductor in case of biased installed sleeve model. The detailed results were presented in the text.