• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.134-146
• /
• 1996

Numerical and experimental studies are performed to investigate the effect of the underbody shape of the simplified road vehicle on drag and life. Four different vehicle models with front and rear slanted variations at the lower surface are used in this study. Cases with a slanted underbody surface at front have smaller drag than those without a slanted surface. Also, cases with a slanted underbody surface at rear have smaller lift than those without a slanted surface. Pressure distributions along the model surfaces and velocity fields at the wake region are examined in detail. In general, numerical solutions are in agreement with experimental results.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권5호
• /
• pp.461-466
• /
• 1997

In this paper, we developed the new non-rubbing liquid crystal (LC) alignment techniques in the cell with slanted non-polarized ultraviolet (UV) light irradiation on polyimide (PI) film. It is shown that the uniform alignment for nematic (N) LC is obtained by using slanted non-polarized UV light irradiation on PI surface. We successfully obtained that the pretilt angle of NLC is generated about 3.3 degree in the cell with slanted non-polarized UV light irradiation with 70 degree on PI surface, for the first time. It is considered that the pretilt angle generation in NLC is attributed to interaction between the LC molecular and the PI, which is broken the polymer by slanted non-polarized UV irradiation. Therefore, we concluded that the uniform LC alignment is attributed to anisotropic dispersion force due to photo depolymerization with slanted non-polarized UV light irradiation on PI surface.

• 제어로봇시스템학회논문지
• /
• 제18권3호
• /
• pp.243-250
• /
• 2012

This paper proposes a 3D map-building algorithm using one LRF (Laser Range Finder) while a mobile robot is navigating on the slanted surface. There are several researches on 3D map buildings using the LRF. However most of them are performing the map building only on the flat surface. While a mobile robot is moving on the slanted surface, the view angle of LRF is dynamically changing, which makes it very difficult to build the 3D map using encoder data. To cope with this dynamic change of the view angle in build 3D map, IMU and balance filters are fused to correct the unstable encoder data in this research. Through the real navigation experiments, it is verified that the fusion of multiple sensors are properly performed to correct the slope angle of the slanted surface. The effectiveness of the balance filter are also checked through the hill climbing navigations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1585-1587
• /
• 1997

We investigated the generation of high pretilt angle for nematic liquid crystal (NLC) in the cell with slanted non-polarized ultraviolet (UV) light irradiation on two kinds of the polyimide (PI) film. It was shown that the monodomain alignment in NLC is obtained in the cell with slanted non-polarized UV light irradiation on PI surface. The pretilt angle of NLC is generated about 3 degrees in the cell with slanted non-polarized UV light irradiation with 70 degrees on PI surface without side chain. But, the pretilt angle of NLC is generated about 1 degree in the cell with slanted non-polarized UV light irradiation with 80 degrees on PI surface with side chain. We consider that the pretilt angle generation in NLC is attributted to anisotropic dispersion force between the LC molecular and the PI surface.

• 한국CDE학회논문집
• /
• 제3권3호
• /
• pp.161-167
• /
• 1998

Cutting forces in ball-end milling of slanted surfaces are calculated. The cutting area is determined from the Z-map of the surface geometry and current cutter location. The obtained cutting area is projected onto the cutter plane normal to the Z-axis and compared with cutting edge element location. Cutting force is calculated by integration of elemental cutting forces of engaged cutting edge elements. Experiments with various slanted angles were performed to verify the proposed cutting force estimation model. It is shown that the proposed method predicts cutting force effectively for any geometry including sculptured surfaces with cusp marks and surfaces with pockets and holes.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.116-119
• /
• 1997

We investigated new type non-robbing liquid crystal (LC) alignment techniques in the cell with slanted non-polarized ultraviolet (UV) irradiation on polyimide (Pl) film. It is shown that the uniform alignment for nematic (N) LC is obtained by using slanted non-polarized UV irradiation on Pl surface. We successfully obtained that the pretilt ang1e of NLC is generated about 3 degree in the LC cells by using slanted non-polarized UV irradiation with 70 degree on Pl surface. We consider that the pretilt angle generation for NLC is attributed to interaction between the LC molecular and the PI surface. We conclude that the uniform LC alignment is attributed to anisotropic dispersion force effect due to photo depolymerization of polymer on Pl surface.

• 전기학회논문지
• /
• 제62권12호
• /
• pp.1730-1736
• /
• 2013

Slanted and chirp interdigital transducer(IDT) configurations were studied for generating the surface acoustic wave(SAW) with wide bandwidths on a piezoelectric substrate. These devices can be applied to manipulate optical path of light along the waveguide, ultimately used for optical switches and holographic image implementation. Prior to fabrication, the coupling of modes(COM) modeling and simulation were performed to extract optimal design parameters. The optimally designed wideband device showed wide bandwidth of 30MHz, low insertion loss of -25dB, and abrupt side suppression ratio (SSR). Several design conditions were determined during device implementation, such as slanted angle, aperture length, number of fingers, and central frequencies of IDTs. These factors were experimentally analyzed and described in details in this paper.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(1)
• /
• pp.241-244
• /
• 2001

The design and fabrication of the surface acoustic wave(SAW) bandpass filters using slanted finger interdigital electrode transducers(IDTs) is investigated. The slanted finger IDTs are used to design SAW filters with good shape factor, a flat passband, and good out-of-band rejection characteristic. The slanted finger IDTS filter was simulated of three kind of IDTs structure. uniform-uniform IDT, uniform-withdrawal weighting IDTS, withdrawal weighting-withdrawal weighting IDTS. Uniform-withdrawal weighting IDTs structure SAW filters was designed and fabricated on 112$^{\circ}$ LiTaO$_3$, 128$^{\circ}$LiNbO$_3$ substrates. Designed SAW filter has about a 30% fractional bandwidth and a 70MHz center frequency.

• 한국전기전자재료학회논문지
• /
• 제15권4호
• /
• pp.325-331
• /
• 2002

In this paper, surface acoustic wave(SAW) bandpass filters using slanted finger interdigital electrode transducers(IDTs) are investigated. The slanted finger IDTs are used to design SAW filters with good shape factor, a flat passband, and good out-of-band rejection characteristic. For the filter design, input-output IDT structure was simulated with modified impulse model; uniform-withdrawal weighting IDTs, withdrawal-withdrawal weighting IDTs. SAW filters of uniform-withdrawal weighting IDTs structure were designed and fabricated on $128^{\circ}LiNbO_3$ piezoelectric substrates. Implemented SAW filter has a fractional bandwidth of 30%, center frequency of 70MHz and shape factor of $1.12\pm0.01$.

• 한국정밀공학회지
• /
• 제15권12호
• /
• pp.212-219
• /
• 1998

During machining of dies and molds with sculptured surfaces. the cutter contact area changes continuously and results in cutting force variation. In order to implement cutting force prediction model into a CAM system, an effective and fast method is necessary. In this paper. a new method is proposed to predict mean cutting force. The cutter contact area in the spherical part of the cutter is obtained using Z-map, and expressed by the grids on the cutter plane orthogonal to the cutter axis. New empirical cutting parameters were defined to describe the cutting force in the spherical part of cutter. Before the mean cutting force calculation, the cutting force density in each grid is calculated and saved to force map on the cutter plane. The mean cutting force in an arbitrary cutter contact area can be easily calculated by summing up the cutting force density of the engaged grid of the force map. The proposed method was verifed through the slotting and slanted surface machining with various inclination angles. It was shown that the mean force can be calculated fast and effectively through the proposed method for any geometry including sculptured surfaces with cusp marks and holes.