• Fisheries and Aquatic Sciences
• /
• 제12권4호
• /
• pp.342-349
• /
• 2009

The purpose of the current study was to optimize shrimp-pot design to allow greater control over the size of captured individuals for the purposes of shrimp resource management. Tank experiments were conducted to determine the optimal slope length and slope angle by analyzing the sizes of shrimp that entered 25 model pots with combinations of five different slope lengths and five different angles. Shrimp size was measured using carapace length. The results showed that as the slope angle of the pot increased, the size of individuals that entered the pot increased. Furthermore, as the slope length increased, each of the five different slope angles of the pot increased, and the size of individuals entering also increased. The data indicated that the optimum pot design for reducing the capture of immature individuals had a $75^{\circ}$ slope angle and a 35.4 cm slope length.

• 패션비즈니스
• /
• 제15권1호
• /
• pp.63-79
• /
• 2011

This study examines the relationship between breast shape and brassiere construction through the comparative analysis of brassiere pattern on the breast shape. This researcher drew the brassiere pattern of developing a pre-study for Chinese female adults according to average size based on the four breast shapes. And then we measures brassiere pattern size and comparatively analyzes breast between size and shape. Comparative analysis results of brassiere patterns are verified differences of size and shape on the breast shape. Above all an angle of cup dart showed remarkable differences on the breast shape. An angle of cup dart isn't proportioned to breast size. An angle of cup dart for cone shape is bigger than dome shape. Because cone shape breast is protruded center part but dome shape breast have a shape of smooth curve like a half globe. So an angle of a cone shape breast cup dart is determined bigger than dome shape breast. For increasing the uplift effect of brassiere, brassiere pattern is different on the breast shape. And a brassiere pattern need different drawing methods about the angle of cup dart, breast inner side diameter, slope and so on. This study has an important significance that it established a mechanical relationship of breast shape and brassiere pattern.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.34-40
• /
• 1998

The burr produced on piece part edges in machining operations must be removed for most parts to function effectively. Although considerable cost have been expended in improving deburring methods, little energy has been applied toward minimizing burrs. This study has been carried out to prevent the burrs produced on pure aluminium under various working condition and specimen shape in turning operations. The computer image processing system was used for measurement of size of burr, such as burr length, burr depth and burr area. The size of burr showed a decreasing tendency with the increase of rake angle and side cutting angle but it increased rapidly with the increase of depth of cut and the cutting speed has no effect on size of burrs. The size of burr rapidly decreased with the increase of edge angle and burrs are not occurred if edge angle is over 80$^{\circ}$.

• 한국의상디자인학회지
• /
• 제5권1호
• /
• pp.85-88
• /
• 2003

In order to design a good ready-made cloth, it is important to consider not only body size but also morphological factor. However, most dissatisfaction of customer is focusing on the size of ready-made cloth which is graded with elements of body size. Various researches on body type have been doing but the study on part of body type is insufficient compared to the study on whole body type. The objective of this paper is to provide relationship of shoulder angle between value in pattern and real measured value after analysis and comparison with these two values.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1522-1527
• /
• 2004

The purpose of this study is to investigate the effect of swirler angle and swirl chamber aspect ration of nozzle on the characteristics of single and twin spray. The performances of nozzle has been investigated by measurements of spray angle, droplet size, velocity and Weber number at a water pressure 0.4MHz. Visualization of spray was conducted to obtain the spray angle and breakup process. The spray characteristics such as droplet size and velocity were measured by Phase Doppler Anemometry(PDA). It was found that the smaller swirler angle, the larger axial velocity became. It was also shown that the larger aspect ratio, the smaller droplet diameter became.

• 한국표면공학회지
• /
• 제37권3호
• /
• pp.175-178
• /
• 2004

The size and number of nano-size defects of thin trivalent chrome layers were determined by small angle neutron scattering (SANS) without breaking the thin chrome layers. Most of defect size of the trivalent chromium prepared in this test conditions is in the range of about 40nm. The number of nano-size defects less than about 40nm of the trivalent chromium layer increases with plating voltage at constant current density From this study, SANS is proved as one of useful techniques to evaluate nano-size defects of thin film layer.

• Journal of Welding and Joining
• /
• 제24권4호
• /
• pp.32-38
• /
• 2006

The objective of present research works is to investigate the effects of process parameters, including the power of laser, cutting speed, material thickness, and the edge angle, on the melted area in the sharp edge of the cut material fur the case of cutting of a low carbon steel sheet using high-power CW Nd:YAG laser. In order to investigate the influence of edge angle and size of loop on the melted area in the sharp edge, angular cutting tests and loop cutting tests have been carried out. From the results of angular cutting tests, the relationship between the edge angle and the melted area has been obtained. The results of the experiments have been shown that the melted area is rapidly reduced from $120^{\circ}$ of the edge angle and the melted area is nearly zero at $150^{\circ}$ of the edge angle. Through the results of loop cutting experiments, the relationship between the cutting angle on the melted area in the edge according to the size of loop have been obtained. In addition, it has been shown that a proper size of loop is nearly 3 mm as the corner angle is greater than $90^{\circ}$ and 5 mm as the comer angle is less than $90^{\circ}$. The results of above experiments will be reflected on the knowledge base to generate optimal cutting path of the laser.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제16권3호
• /
• pp.390-395
• /
• 1994

The author evaluated the nasal asymmetry after primary operations in the patients with unilateral cleft lip using full face photographs. The results are as follows : 1. Nasal deviation angle is average 2.98+3.01 degree(ranged from 0 to 10 degree), significantly different from control group(p<0.05). 2. Nasal deviation angle is average 5.1% when inter-medial canthal distance is 100%, significantly different from control group(p<0.05). 3. Difference in nostril size between cleft and noncleft side is 2.1% when inter-medial canthal distance is 100%, significantly different from control group(p<0.05). 4. Nasal attractiveness analysis shows higher points in difference in nostril size, nasal deviation, nasal form in that order. 5. Nasal asymmetry after primary operations in the patients with unilateral cleft lip using full face photographs is related with Nasal deviation angle, Nasal deviation distance and Difference in nostril size between cleft and noncleft side.

• 대한통합의학회지
• /
• 제7권3호
• /
• pp.149-157
• /
• 2019

Purpose : This study aims to check the relationship between the size of curvature in scoliosis patients and the reduction rate of curvature after wearing a brace and the relationships of the size of curvature and correction angle with Body Mass Index (BMI). Methods : With 30 adolescent girls who had never worn a brace, their Cobb angle and BMI were measured before manufacturing braces, and their corrected Cobb angle was measured after wearing the manufactured scoliosis braces. Results : The size of the major curvature before wearing the brace and the reduction rate of the curvature after putting it on had a negative correlation in both the major curvature (r=-.465, p<.01) and the minor curvature (r=-.516, p<.01). The size of the minor curvature and the reduction rate of the minor curvature before and after putting it on also had a negative correlation (r=-.429, p<.05). As for the relationship between the size of curvature and BMI, they had a negative correlation in both the major curvature (r=-.141) and the minor curvature (r=-.123), and as for the relationship between the reduction rate of curvature and BMI after wearing the brace, they had a positive correlation in both the major curvature (r=.251) and the minor curvature (r=.136); however, it was not statistically significant (p>.05). Conclusion : In conclusion, the larger the size of curvature, the lower the reduction rate of curvature after wearing the brace became. The larger the size of curvature, the lower the BMI became. The higher the BMI, the higher the correction ratio of the brace became. Therefore, it is judged that it is necessary to provide early treatment and manage body composition before scoliosis progresses.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.111-117
• /
• 2012

Dust collecting performance of axial-vane type cyclone for oil mist was analyzed in this study. For predicting cut diameter size of cyclone, the number and angle of vane ($tan{{\beta}_2}^{\prime}$) was simulated by CFD. As the result, $tan{{\beta}_2}^{\prime}$ was decreased as the number of vane was increased and the angle of inclination(${{\beta}_2}^{\prime}$) decreased, and it cause strong swirl flow. Therefore, it could be confirmed that as the number of vane was increased and the angle of inclination was decreased, cut diameter size was decreased. Also, by verifying the results of CFD through experiment, the cut diameter size could be $2{\mu}m$ at $4m^3/min$ of flow rate.