• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.228-234
• /
• 1989

Pressureless-sintering of SiC with additions of yttria and alumina was studied. SiC could be densified to about 97% of its theoretical density at 185$0^{\circ}C$ which is about 20$0^{\circ}C$ below the normal sintering temperature of SiC with boron and carbon. Yttria and alumina formed intergranular liquid phases at the sintering temperature and promoted densification by the liquid phase sintering mechanism. The microstructure of sintered specimens was equiaxed and the liquid phase appeared to wet and dissolve SiC grains. The fracture toughness was measured by indentation method and found to be 5.3MPa.m1/2. Processing flaws near the surface of specimens appeared to be the major fracture origin during 3-point bending tests.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.4
• /
• pp.1194-1201
• /
• 1996

For the case of creep-fatigue interaction, the damage zone developed in front of the growing crack-tip during creep regime is important because it can affect the damage mechanism to be occured by the following fatigue load. These are studied in theis paper through proper consideration of the cavitiy-size dependent sintering stress which is approximated by polynomials. It is shown that the inclination of reversed damage zone size with respect to the applied load parameter can be explained by considering realistic sintering stress distribution. However, the resultant stress field has $r^{1/2+\theta}$ singularity, regardliss of the profile of variable sintering stress, which is the same to that case solved for constant sintering stress.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.117-120
• /
• 1999

The relationship between the DC degradation characteristics of the ZnO varistor and the ambient sintering-process is investigated in this study. ZnO varistors made of Matsuoka's composition were fabricated by standard ceramic techniques. The ambient sintering-process is performed at the extraordinary electrical-furnace which is equipped with the vacuum system. The Gas of sintering process was oxygen, nitrogen, argon, air respectively. The microstructure of ZnO varistors be made use of SEM equipment. The condition of DC degradation tests were conducted at $115\pm2^{\circ}C$ for periods up to 13 h. Current-voltage analysis is used to determine nonlinear coefficients($\alpha$). Resistance-frequency and capacitance-frequency analysis are accomplished to the understanding of electrical properties as DC degradation test. From above analysis, it is found that the ZnO varistor sintered in oxygen atmosphere showed superior properties at the DC degradation test.

• 한국기계연구소 소보
• /
• s.9
• /
• pp.67-74
• /
• 1982

• Journal of Powder Materials
• /
• v.1 no.1
• /
• pp.79-84
• /
• 1994

The mechanism of activated sintering of tungsten powder was discussed in terms of diffusion and segregation of activator atoms at W grain boundaries. Shrinkage behaviours of W-0.2wt.% Ni, W-0.2wt.% Cu or pure W powder compacts during sintering at low temperatures of 900~ $1200^{\circ}C$ were investigated. It was found that the Cu additive inhibits sintering process causing lower densification than pure W compact while remarkable shrinkage occurred in the Ni added W powder. Such contrary effect was explained by comparing self diffusion processes along Ni or Cu segregated W boundaries in which Ni segregants enhance but Cu atoms retard the migration of W atoms at W boundaries.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1323-1324
• /
• 2006

Refractory materials, such as W and Mo, are very useful elements for use in high-temperature applications. But it is not easy to fabricat pure W and Mo with very high density and retaining very fine grain size because of their high melting point. In this paper, a newly developed method named as resistance sintering under ultra high pressure was use to fabricate pure fine-grained W and Mo. The microstructure was analysis by SEM. The sintering mechanism is primary analyzed. Basic physical property of these sintered pure W and Mo, such as hardness, bend strength, are tested.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.110-114
• /
• 1999

NOx sensing properties of $Ba_2WO_5$ were investigated by varying the sintering temperature in an effort to study the effects of the neck-width on gas sensitivity. $Ba_2WO_5$ sintered at $800^{\circ}C$, which exhibits neck-controlled conduction provides highest sensitivity of 47 and 29 at $500^{\circ}C$ to NO and $NO_2$, respectively. The samples sintered beyond $800^{\circ}C$ show sintering temperature-independent gas sensitivity. This may be because the grain boundary control is dominant at lower sintering temperatures and open neck control is dominant at higher sintering temperatures than $800{\circ}C$. The NOx sensing mechanism of $Ba_2WO_5$ was briefly discussed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.62-63
• /
• 2006

Both densification and grain growth are driven by the reduction of the interfacial area, kinetics of which depends strongly on the interface structure. Abnormal grain coarsening in the system of singular solid/liquid interface such as WC-Co alloys was explained by the growth mechanism of 2-dimensional nucleation. Based on this concept, the marked inhibition of coarsening of WC grains by VC addition can be approached by the increase in the step free energy, which increases the barrier of 2-dimensional nucleation. The activated sintering in tungsten powders can be approached by the interface structure change induced by the addition of a small amount of nickel.

• Journal of Sensor Science and Technology
• /
• v.26 no.3
• /
• pp.214-222
• /
• 2017

In this study, the effects of internal heat treatment associated sintering temperatures were simulated by the Finite Element Method (FEM). The sintering mechanism of pulsed current activated sintering process (PCAS) is still unclear because of some unexplainable heat transfer phenomena in coupled multi-physical fields, as well as the difficulty in measuring the interior temperatures of metal powder. We have carried out simulation study to find out thermal distributions between graphite mold and Ruthenium powder prior to PCAS process. For PCAS process, heating rate was maintained at $100^{\circ}C/min$ the simulation indicates that the sintering temperature range was between $1000^{\circ}C$ to $1300^{\circ}C$ under 60 MPa. The heat transfer inside the Ruthenium sintered-body sample was modelled through the whole process in order to predict the minimum interior temperature. Thermal simulation shows that the interior temperature gradient decreased by graphite punch length and calculation results well agreed with the PCAS field test results.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.140-144
• /
• 2005

The microstructures and mechanical properties of Tetragonal Zirconia Polycrystals (TZP) sintered bodies, which made by pressureless and spark plasma sintering techniques, were investigated using XRD, SEM, and TEM techniques. In the spark plasma sintered samples, the TZP grains were equiaxed type including many sub-grain boundaries regardless of sintering conditions. The biaxial strength of TZP having an average of 80 nm grains in diameter was high in value with 1025 MPa, but fracture toughness showed a low value due to the absence of a fracture toughening mechanism such as transformation toughening. In the Pressureless Sintered (PLSed) samples, the grain size of TZP was strongly dependent on the sintering temperature; i.e., it gradually increased as the sintering temperature increased. The value of fracture toughness increased as the grain size increased by the stress-induced phase transformation and Borne crack deflection.