• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1167-1171
• /
• 2008

The flow and thermal performance of the skiving and louver fin type heat sinks for the cooling system of the small LED projector were experimentally evaluated. A small fan tester based on AMCA standards was used to control and measure the air flow rate into the heat sink. Three heat blocks were used to simulate the heat and light sources(red, green and blue) of the small LED projector. We measured the pressure drop, temperatures and input power at the specific air flow rate and discussed those results. As a result, it is found that the louver fin type heat sink has higher pressure drop and lower thermal resistance than the skiving type. From the comparison of the temperature of the heat block between skiving and louver fin type, the louver fin type heat sink was found to be more suitable for cooling the high power heat source than skiving type. The thermal performance of the fan-sink(louver fin type) system was discussed with the picture taken by a thermal video.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.1
• /
• pp.1-8
• /
• 2015

In the present study, the effects of the heat spreader thickness and the heat sink size on the thermal performance of a cooling device for a concentrating photovoltaic (CPV) module were numerically investigated. Numerical simulation was conducted by using the simulation tool ICEPAK, commercial software based on the finite volume method. Numerical results were validated by comparing the existing experimental data. The thermal performance of a cooling device, which consisted of a heat spreader and a natural convective heat sink, was evaluated with varying the heat spreader thickness and the heat sink size. The geometric configuration of the natural convective heat sink, such as the fin height, the fin spacing, and the fin thickness, was optimized by using the existing correlation. The numerical results showed that the thermal performance of the cooling device increased as the heat spreader thickness or the heat sink size increased. Also, it was found that the spreading thermal resistance plays an important role in the thermal performance of the cooling device which has the localized heat source.

• Journal of Korea Society of Industrial Information Systems
• /
• v.9 no.2
• /
• pp.65-73
• /
• 2004

By the progress of communication and hardware technology, It is possible to organize wireless sensor nodes using the tiny sensor in recently. It is a critical aspect to minimize energy consumption for long-term lively sensor because wireless sensor nodes are associated with the available resources. The wireless sensor network is restricted in communication, exhaustion of power, and computation but it is very similar an Ad-Hoc network. Each sensor node products a few data and application layer of each sensor has slow transmitting feature. Unlike Ad-hoc, which is usually source or sink, base station of the each senor nodes works as sink and the other nodes except sink node works as source. Generally, wireless sensor network keep staying fixed state and observing circumstances continuously after setting up. It doesnt fit for the wireless sensor networks under functioning of existing ad-hoc networks because original Ad-Hoc network routing protocol couldnt operate for wireless sensor network features. This thesis propose the effective routing protocol way in the filed of the expanded routing protocol based on tree with considering on the characteristic of wireless sensor networks pattern.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.172-181
• /
• 1993

Pseudo-Brayton cycle is defined as an ideal Brayton cycle admitting the difference between heat capacities of working fluid during heating and cooling processes. The endo-pseudo-Brayton cycle which is a pseudo-Brayton cycle with heat transfer processes is analyzed with the consideration of maximum power conditions and the results were compared with those of the endo-Carnot cycle and endo-Brayton cycle. As results, the maximum power is an extremum with respect to the cycle temperature and the flow heat capacities of heating and cooling processes. At the maximum power condition, the heat capacity of the cold side is smaller than that of heat sink flow. And the heat capacity of endo-Brayton cycle is always between those of heat source and sink flows and those of the working fluids of pseudo-Brayton cycle. There is another optimization problem to decide the distribution of heat transfer capacity to the hot and cold side heat exchangers. The ratios of the capacies of the endo-Brayton and the endo-pseudo-Braton cycles at the maximum power condition are just unity. With the same heat source and sink flows and with the same total heat transfer caqpacities, the maximum power output of the Carnot cycle is the least as expected, but the differences among them were small if the heat transfer capacity is not so large. The thermal efficiencies of the endo-Brayton and endo-Carnot cycle were proved to be 1-.root.(T$_{7}$/T$_{1}$) but it is not applicable to the pseudo-Brayton case, instead it depends on comparative sizes of heat capacities of the heat source and sink flow.w.

• Journal of computational fluids engineering
• /
• v.18 no.2
• /
• pp.9-16
• /
• 2013

The heat transfer enhancement of heat sink with mist flow is studied numerically by solving the conservation equations for mass, momentum and energy in the continuous and dispersed phases. A Lagrangian method is used for tracing dispersed water droplets in the heat sink and an Eulerian species transport model for air and steam mixture. The continuous and dispersed phases are interacted with the drag and evaporation source terms. The computed results show that addition of evaporating mist droplets enhances the cooling performance of heat sink significantly.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.2
• /
• pp.260-267
• /
• 1995

In temperate zone planting rice at different date subjects the Crop to different climatic condition. The present study aimed at comparison of the change in source-sink relationship of the Japonica(J) and that of IndicaxJaponica(I$\times$J) type rice cultivars caused by shift of heading date. Two J- and two I$\times$J-type cultivars were made to head on August 16, August 26, and September 5. Sink capacity was changed by shift of heading date in different mode between the types of cultivars. In both types major determinant of sink capacity was number of effective tillers, and the number of spikelets per panicle was the minor. In J-type earlier planting/heading was beneficial to increased panicle numbers and this was due mainly to a larger diurnal difference in temperature. I$\times$J-type cultivars favored a higher daily mean temperature to increase the sink capacity. The ability of source at heading, in terms of leaf area per panicle, chlorophyll content per spiklet, photosynthetic ability of leaves per unit area at 25$\^{\circ}C$, carbohydrate and N contents of leaves, was not so different among different heading dates in both types. However, the source activity was governed principally by temperature during grain filling. The J-type cultivars headed on Sept. 5 and I$\times$J-type cultivars headed later than August 16 could not have had sufficient source activity in grain filling due to lower temperature.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 1981.10a
• /
• pp.17-19
• /
• 1981

• Proceedings of the Korean Society of Crop Science Conference
• /
• 1980.05a
• /
• pp.33.1-33.1
• /
• 1980

• Proceedings of the Korean Society of Crop Science Conference
• /
• 1985.05a
• /
• pp.13-13
• /
• 1985

• Proceedings of the Korean Society of Crop Science Conference
• /
• 1982.10a
• /
• pp.3-4
• /
• 1982