• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.871-875
• /
• 1998

A DSP-based source current control for power conditioner is presented to compensate current harmonics and asymmetries of three-phase four-wire emergency generators caused by nonlinear and/or unbalanced loads. There-phase voltage type converter with split-dc-capacitor is adopted as the power circuit and a new direct source current control method is suggested, which simplifies the controller. The proposed control method shapes the generator current sinusoidally inphase with the voltage and allows the generator to supply maximum power even to single phase loads. An IGBT base lookVA prototype with the controller realized with a DSP (TMS320C32) is built and tested to verify the performance of the power conditioner.

• International Journal of Aeronautical and Space Sciences
• /
• v.2 no.2
• /
• pp.39-45
• /
• 2001

To reduce the strength of tip vortex of the fixed wing, a horizontal wing-let splitted into two parts was utilized, and the interaction between vortices generated by these wing-lets was investigated by the hot-wire anemometry. The process of vortex forming and merging was clarified by measurements of velocity vectors and their contours at five downstream cross-sections; 0.05C(chord length), 0.2C, 0.5C, 1.0C and 2.0C. Both vortex-lets formed by each wing-lets rotate counterclockwise and merge into a larger single vortex within a short downstream distance, 0.5C in this case. The strength of the merged tip vortex turned out to become smaller than that of the plain wing tip near the vortex core.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.681-682
• /
• 2006

This paper deals with the preliminary study on the HTSC levitation magnet for MAGLEV operating in persistent current mode (PCM). The high temperature superconducting (HTSC) levitation magnet consists of two single-pancake type coils wound with Bi-2223 wire and a persistent current switch (PCS). The levitation magnet was designed by using 3-D finite element analysis. The suspension system for high-speed electrodynamic suspension (EDS) maglev should operated in persistent current mode. It is important to develop a technology to minimize the joint resistance of splice between two HTSC wires. The PCS was observed with respect to various magnitude of charging current. Based on these results, the levitation system using HTSC wire will be further studied.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.233-236
• /
• 2000

A portable equipment that measures a current and voltage waveform of power transmission lines is pro-posed. In the equipment, the current and voltage, respectively, are detected by a loop coil and a capacitor clamped around the power lines. The detected data is transmitted by an FM wave to the receiver on the ground station. Since the receiver is isolated from the power lines, we do not require high potential insulators for the measurement of current and voltage. The proposed equipment is therefore, small-sized, light, and low in the cost of production. Experimental results presented here show that the equipment can monitor the current flowing in single wire over a ground plane and the potential of the wire.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.504-506
• /
• 2005

This paper proposes a new neutral current reduction method using PQR instantaneous power theory on the active power filter, unbalanced nonlinear load condition in three-phase four-wire systems. For reduction of neutral line current, the single phase active power filter is used and its performance is same with the three-phase four-wire active power filter. For fully-digital implementation, ramp comparison PWM method was adopted. Simulation results verify good performance of the proposed current control strategy on the shunt APFs.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.2
• /
• pp.153-161
• /
• 1998

This study describes the results of the analysis of measured rotating stall signal in a centrifugal compressor with vaneless diffuser. Unsteady flow and rotating stall in vaneless diffuser were investigated by measuring of unsteady velocity fluctuation using hot-wire anemometer. Experiments were carried out in several impeller rotating speeds, at different radius ratios. Single hot -wire was used to study the characteristics of rotating stall. As a result, the abrupt rotating stall was detected at all measured impeller rotating speeds and the several flow coefficients which are less than 0.16. The number of the stall cell was one at all measured rotational speeds, and the rotating direction was the same as that of the impeller. As the flow rate decreased, the profile of the phase averaged radial velocity component with time changed from a sawtooth to a sine wave.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.55 no.2
• /
• pp.67-72
• /
• 2006

Most of the load distributions in low voltage power feeder distribution systems are designed with approximately balanced and connected at the three phase four wire systems. However, in the user power distribution systems, most of the loads are single & three phase and unbalanced, generating load unbalance. Load unbalance factor is mainly affected by the impedance of load system. Unbalanced current will draw a highly unbalanced voltage. This paper presents a new calculation method for unbalance factor under the load variation at the three phase four wire system. Load unbalance factor is measured by the power quality measurement apparatus and compared with the current unbalance factor. Two methods are indicated similar results.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.4
• /
• pp.755-760
• /
• 2019

In this paper, we developed the multi-tool carving machine which integrates the existing hot-wire carving machine, hot-wire cutting machine and spindle so that the shape of complex structure can be produced easily and quickly. We have also developed software that solves the problem that G-Code applies only to a single tool, and controls the details of the machine's operations that can not be managed with existing 3D modeling tools.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.4
• /
• pp.93-102
• /
• 1995

This paper introduces a general purpose Associative Processor(AP) which is very efficient for search-oriented applications. The proposed architecture consists of three main functional blocks: Content-Addressable Memory(CAM) arry, row logic, and control section. The proposed AP is a Single-Instruction, Multiple-Data(SIMD) device based on a CAM core and an array of high speed processors. As an application for the proposed hardware, we present a parallel algorithm to solve a global routing problem in the layout process utilizing the processing capabilities of a rudimentary logic and the selective matching and writing capability of CAMs, along with basic algorithms such a minimum(maximum) search, less(greater) than search and parallel arithmetic. We have focused on the simultaneous minimization of the desity of the channels and the wire length by sedking a less crowded channel with shorter wire distance. We present an efficient mapping technique of the problem into the CAM structure. Experimental results on difficult examples, on randomly generated data, and on benchmark problems from MCNC are included.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.3
• /
• pp.34-37
• /
• 2003

A 1 MVA single-phase high temperature superconducting (HTS) transformer with BSCCO-2223 wire was designed in this paper. The rated voltages of each sides of the transformer are 22.9 kV and 6.6 kV respectively. Double pancake HTS windings arranged reciprocally will be used for the transformer windings, because of the advantages of insulation and distribution of surge voltage in case of a large power and high voltage transformer. Single HTS wire was used for the primary windings and four parallel wires were used for the secondary windings of the transformer with transposition. A core of the transformer was designed as a shell type core separated with the windings by a cryostat made of GFRP with a room temperature bore. The operating temperature of the HTS windings will be about 65K with sub-cooled liquid nitrogen. A cryogenic cooling system using a GM-cryocooler for this HTS transformer by natural convection of liquid nitrogen was designed. This type of cooling system can be a good option for compactness, efficiency, and reliability of the HTS transformer.