• 제목/요약/키워드: single power-conversion

검색결과 386건 처리시간 0.032초

Electrical and Optical Properties of Asymmetric Dielectric/Metal/Dielectric (D/M/D) Multilayer Electrode Prepared by Radio-Frequency Sputtering for Solar Cells

  • Pandey, Rina;Lim, Ju Won;Lim, Keun Yong;Hwang, Do Kyung;Choi, Won Kook
    • 센서학회지
    • /
    • 제24권1호
    • /
    • pp.15-21
    • /
    • 2015
  • Transparent and conductive multilayer thin films consisting of three alternating layers FZTO/Ag/$WO_3$ have been fabricated by radio-frequency (RF) sputtering for the applications as transparent conducting oxides and the structural and optical properties of the resulting films were carefully studied. The single layer fluorine doped zinc tin oxide (FZTO) and tungsten oxide ($WO_3$) films grown at room temperature are found to have an amorphous structure. Multilayer structured electrode with a few nm Ag layer embedded in FZTO/Ag/$WO_3$ (FAW) was fabricated and showed the optical transmittance of 87.60 % in the visible range (${\lambda}=380{\sim}770nm$), quite low electrical resistivity of ${\sim}10^{-5}{\Omega}cm$ and the corresponding figure of merit ($T^{10}/R_s$) is equivalent to $3.0{\times}10^{-2}{\Omega}^{-1}$. The resultant power conversion efficiency of 2.50% of the multilayer based OPV is lower than that of the reference commercial ITO. Asymmetric D/M/D multilayer is a promising transparent conducting electrode material due to its low resistivity, high transmittance, low temperature deposition and low cost components.

서브샘플링 직접변환 수신기용 5.3GHz 광대역 저잡음 증폭기 (A 5.3GHz wideband low-noise amplifier for subsampling direct conversion receivers)

  • 박정민;서미경;윤지숙;최부영;한정원;박성민
    • 대한전자공학회논문지SD
    • /
    • 제44권12호
    • /
    • pp.77-84
    • /
    • 2007
  • 본 논문에서는 $0.18{\mu}m$ CMOS 공정을 이용하여 서브샘플링 직접변환방식 RF 수신기용을 위한 광대역 저잡음 증폭기를 구현하였다. 인버터-형태의 트랜스임피던스 입력단과 3차의 Chebyshev 매칭네트워크를 사용함으로써, 제안한 광대역 저잡음 증폭기 회로는 5.35GHz의 대역폭, $12\sim18dB$의 전력이득, $6.9\sim10.8dB$의 NF, 대역폭 내에서의 -10dB 이하의 입력 임피던스 매칭과 -24dB 이하의 출력 임피던스 매칭을 얻었다. 제작한 칩은 1.8V 단일 전원전압으로 부터 32.4mW의 전력소모를 가지며, $0.56\times1.0mm^2$의 칩 사이즈를 갖는다.

6단자망 회로모델을 이용한 전기철도 급전시스템의 고조파 해석 (Harmonic Analysis for Traction Power Supply System Using Four-Port Network Model)

  • 창상훈;오광혜;김주락;김정훈
    • 대한전기학회논문지:전력기술부문A
    • /
    • 제51권6호
    • /
    • pp.255-261
    • /
    • 2002
  • Recently, traction motors in trains are supplied with single phase a.c. power. After this power is converted to d.c. power, it is inverted to three phase power to operate traction motors. As going through the process of the conversion, harmonic current is generated in train. The method of conventional analysis on harmonics, studied by RTRI, is modeled with equivalent circuit of ac AT-fed electric railroad system using by the distributed constant circuit. However, this circuit as two-port network model has some difference in comparison with real system. The reason why the conventional method is different from the real system is that the conventional method dose not include three conductor groups, that is catenary, rail, and feeder, and admittance between the conductors for line capacitance. Therefore, this method has a little error. This paper proposes new method to more effectively estimate Harmonic current. In this method, numerous components in electric railway are categorized and each component is defined as a four- port network model. The equivalent circuit for the entire power supply system is also described into a four-port network model with connections of these components. In order to evaluate the efficiency and the accuracy of a proposed method, it is compared with values measured in Kyung-Bu high speed line and ones calculated by the conventional method.

호지킨-헉슬리 모델을 위한 시냅스 기능을 지닌 신경세포 체인의 하드웨어 구현 (Hardware implementation of a pulse-type neuron chain with a synapse function for hodgkin-huxley model)

  • 정진우;권보민;박주홍;김진수;이제원;박용수;송한정
    • 센서학회지
    • /
    • 제18권2호
    • /
    • pp.128-134
    • /
    • 2009
  • Integrated circuit of a new neuron chain with a synapse function for Hodgkin-Huxley model which is a good electrical model about a real biological neuron is implemented in a $0.5{\mu}m$ 1 poly 2 metal CMOS technology. Pulse type neuron chain consist of series connected current controlled single neurons through synapses. For the realization of the single neuron, a pair of voltage mode oscillators using operational transconductance amplifiers and capacitors is used. The synapse block which is a connection element between neurons consist of a voltage-current conversion circuit using current mirror. SPICE simulation results of the proposed circuit show 160 mV amplitude pulse output and propagation of the signal through synapses. Measurements of the fabricated pulse type neuron chip in condition of ${\pm}2.5\;V$ power supply are shown and compared with the simulated results.

Tunable Electrical Properties of Aligned Single-Walled Carbon Nanotube Network-based Devices: Metallization and Chemical Sensor Applications

  • Kim, Young Lae;Hahm, Myung Gwan
    • 한국세라믹학회지
    • /
    • 제54권6호
    • /
    • pp.535-538
    • /
    • 2017
  • Here we report the tunable electrical properties and chemical sensor of single-walled carbon nanotubes (SWCNTs) network-based devices with a functionalization technique. Formation of highly aligned SWCNT structures is made on $SiO_2/Si$ substrates using a template-based fluidic assembly process. We present a Platinum (Pt)-nanocluster decoration technique that reduces the resistivity of SWCNT network-based devices. This indicates the conversion of the semiconducting SWCNTs into metallic ones. In addition, we present the Hydrogen Sulfide ($H_2S$) gas detection by a redox reaction based on SWCNT networks functionalized with 2,2,6,6-Tetramethylpiperidine-1-oxyl (TEMPO) as a catalyst. We summarize current changes of devices resulting from the redox reactions in the presence of $H_2S$. The semiconducting (s)-SWCNT device functionalized with TEMPO shows high gas response of 420% at 60% humidity level compared to 140% gas response without TEMPO functionalization, which is about 3 times higher than bare s-SWCNT sensor at the same RH. These results reflect promising perspectives for real-time monitoring of $H_2S$ gases with high gas response and low power consumption.

Enhanced Photovoltaic Performance of Perovskite Solar Cells by Copper Chloride (CuCl2) as an Additive in Single Solvent Perovskite Precursor

  • Kayesh, Md. Emrul;Matsuishi, Kiyoto;Chowdhury, Towhid H.;Kaneko, Ryuji;Noda, Takeshi;Islam, Ashraful
    • Electronic Materials Letters
    • /
    • 제14권6호
    • /
    • pp.712-717
    • /
    • 2018
  • In this letter, we have introduced copper chloride ($CuCl_2$) as an additive in the $CH_3NH_3PbI_3$ precursor solution to improve the surface morphology and crystallinity of $CH_3NH_3PbI_3$ films in a single solvent system. Our optimized perovskite solar cells (PSCs) with 2.5 mol% $CuCl_2$ additive showed best power conversion efficiency (PCE) of 15.22%. The PCE of the PSCs fabricated by $CuCl_2$ (2.5 mol%) additive engineering was 56% higher than the PSC fabricated with pristine $CH_3NH_3PbI_3$.

Series Compensated Step-down AC Voltage Regulator using AC Chopper with Transformer

  • Ryoo, H.J.;Kim, J.S.;Rim, G.H.
    • KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
    • /
    • 제5B권3호
    • /
    • pp.277-282
    • /
    • 2005
  • This paper describes a step-down AC voltage regulator using an AC chopper and auxiliary transformer, which is a series connected to the main input. The detail design of the AC regulator, logic and PWM pattern of the AC chopper is described and the three-phase AC regulator using two single­phase AC choppers with a three transformer configuration is proposed for three-phase application. The proposed three-phase system has the advantages of lower system cost due to reduced switch number and gate driver circuit as well as advantages of decreased size and weight because it uses a series compensated scheme. The proposed AC regulator has many benefits such as fast voltage control, high efficiency and simple control logic. Experimental results indicate that it can be used as a step-down AC voltage regulator for power saving purposes very efficiently.

CuPc/$C_{60}$ 이중층을 이용한 유기 광기전 소자의 전기적 특성 (Electrical Properties of Organic Photovoltaic Cell using CuPc/$C_{60}$ double layer)

  • 이호식;박용필
    • 한국정보통신학회:학술대회논문집
    • /
    • 한국해양정보통신학회 2008년도 춘계종합학술대회 A
    • /
    • pp.744-746
    • /
    • 2008
  • Organic photovoltaic effects were studied in a device structure of ITO/CuPc/Al and ITO/CuPc/$C_{60}$/BCP/Al. A thickness of CuPc layer was varied from 10 nm to 50 nm, we have obtained that the optimum CuPc layer thickness is around 40 nm from the analysis of the current density-voltage characteristics in CuPc single layer photovoltaic cell. From the thickness-dependent photovoltaic effects in CuPc/$Cu_{60}$ heterojunction devices, higher power conversion efficiency was obtained in ITO/20nm CuPc/40nm $C_{60}$/Al, which has a thickness ratio (CuPc:$C_{60}$) of 1:2 rather than 1:1 or 1:3. Light intensity on the device was measured by calibrated Si-photodiode and radiometer/photometer of International Light Inc(IL14004).

  • PDF

Improving Device Efficiency for n-i-p Type Solar Cells with Various Optimized Active Layers

  • Iftiquar, Sk Md;Yi, Junsin
    • Transactions on Electrical and Electronic Materials
    • /
    • 제18권2호
    • /
    • pp.70-73
    • /
    • 2017
  • We investigated n-i-p type single junction hydrogenated amorphous silicon oxide solar cells. These cells were without front surface texture or back reflector. Maximum power point efficiency of these cells showed that an optimized device structure is needed to get the best device output. This depends on the thickness and defect density ($N_d$) of the active layer. A typical 10% photovoltaic device conversion efficiency was obtained with a $N_d=8.86{\times}10^{15}cm^{-3}$ defect density and 630 nm active layer thickness. Our investigation suggests a correlation between defect density and active layer thickness to device efficiency. We found that amorphous silicon solar cell efficiency can be improved to well above 10%.

Benchmark Results of a Radio Spectrometer Based on Graphics Processing Unit

  • Kim, Jongsoo;Wagner, Jan
    • 천문학회보
    • /
    • 제40권2호
    • /
    • pp.44.1-44.1
    • /
    • 2015
  • We set up a project to make spectrometers for single dish observations of the Korean VLBI Network (KVN), a new future multi-beam receiver of the ASTE (Atacama Submillimeter Telescope Experiment), and the total power (TP) antennas of the Atacama Large Millimeter/submillimeter Array (ALMA). Traditionally, spectrometers based on ASIC (Application-Specific Integrated circuit) and FPGA (Field-Programmable Gate Array) have been used in radio astronomy. It is, however, that a Graphics Processing Unit (GPU) technology is now viable for spectrometers due to the rapid improvement of its performance. A high-resolution spectrometer should have the following functions: poly-phase filter, data-bit conversion, fast Fourier transform, and complex multiplication. We wrote a program based on CUDA (Compute Unified Device Architecture) for a GPU spectrometer. We measured its performance using two GPU cards, Titan X and K40m, from NVIDIA. A non-optimized GPU code can process a data stream of around 2 GHz bandwidth, which is enough for the KVN spectrometer and promising for the ASTE and ALMA TP spectrometers.

  • PDF