• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.298-305
• /
• 2003

We have calculated the single mode yield of index-coupled (IC) DFB lasers above threshold for several kL, and facet reflectivity combinations, and investigated the correlation between those results and the single mode yield as a function of f number at the threshold. As a result, there is little correlation between the single mode yield above threshold and the single mode yield as a function of f number at the threshold. The single mode yields above threshold for kL of 0.8 and 1.25 is larger than those for kL, of 2 and 3 due to the spatial hole burning effect. Also, we have investigated the effect of the reflectivity of the AR facet on the single mode yield for AR-HR and AR-CL combinations. For AR-HR combinations, the single mode yield increases as the reflectivity of the AR facet decreases. However, for AR-CL combinations, the reflectivity of the AR facet for the largest single mode yield exists. In the single mode yield calculations for IC DFB lasers in this paper, the single mode yield for kL of 0.8 with AR(1％)-HR combination is largest above threshold.

• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.521-529
• /
• 2003

For complex-coupled (CC) DFB lasers, we found that there might be little correlation between the single mode yields at threshold and above threshold. At threshold, the single mode yield considering f number of in-phase (IP) CC DFB lasers is the same as that of anti-phase (AP) CC DFB lasers. However, the single mode yield as a function of injection current above threshold of IP CC DFB lasers is much different from that of AP CC DFB lasers. In the case of IP CC DFB lasers, the single mode yield increases as the coupling coefficient ratio (CR) increases, while, in the case of AP CC DFB lasers, the single mode yield decreases rapidly regardless of CR as the injection current increases. In the case of AR-HR combinations, the effect of AR ref1ectivity on the single mode yield increases as the coupling strength decreases. As the coupling strength decreases, the CR at which the increase rate of the single mode yield starts to decrease, increases, and the maximum single mode yield increases. Single mode yields of AR-HR and AR-AR combinations are larger than those of AR-CL and CL-CL combinations.

• Korean Journal of Optics and Photonics
• /
• v.15 no.2
• /
• pp.149-157
• /
• 2004

We have calculated the power extraction efficiency and the lasing wavelength distribution of complex-coupled(CC) DFB lasers above threshold for various｜$\chi$L｜ and facet reflectivity combinations, and we have compared the results with those at threshold. Also, we have investigated the effect of coupling coefficient ratio(CR) and the reflectivity of AR facet on the power extraction efficiency and the lasing wavelength distribution. At threshold, the single mode yield as a function of power extraction efficiency of in-phase(IP) CC DFB lasers is the same as that of anti-phase(AP) CC DFB lasers. Above threshold, however, the single mode yield as a function of power extraction efficiency of IP CC DFB lasers is much larger than that of AP CC DFB lasers. For IP CC DFB lasers, AR-HR combination has high single mode yield and large power extraction efficiency compared to other facet combinations. IP CC DFB laser with AR-HR combination for ｜$\chi$L｜of 0.8 has the highest single mode yield and largest power extraction efficiency above threshold among the cases considered. For AR-HR combination, as CR increases and the reflectivity of AR facet decreases, both single mode yield and power extraction efficiency increase due to the reduction of the spatial hole burning effect. For AR-HR combination, the lasing wavelength of CC DFB laser has distributed over the stopband of DFB. As CR increases, the lasing wavelength concentrates on the long wavelength side for IP CC DFB laser, while on the short wavelength side for AP CC DFB laser. As ｜$\chi$L｜ increases, the width of the wavelength distribution decreases and the lasing wavelength moves to the long wavelength side.

• Journal of Veterinary Clinics
• /
• v.39 no.4
• /
• pp.149-155
• /
• 2022

The aim of this study was to compare the mechanical properties of 0.6 and 0.8 mm cerclage wires with the 1.0 mm cerclage wire in the twist, single-loop, double-loop, double-wrap, and loop/twist knot methods. Six stainless steel cerclage wires of various diameters in different knot methods were tied round a customized jig mounted on a load testing machine. The initial tension, initial stiffness, and yield load were evaluated. The failure mode of each cerclage was observed. For each wire size, the double-loop, double-wrap, and loop/twist knots showed significantly greater initial stiffness, and yield load than those seen with twist and single-loop knots. The single-loop knot showed the least initial stiffness regardless of the diameter. As the cerclage wire diameter increased, the cerclage tended to show significantly greater initial stiffness, and yield load. Failure modes varied depending on the knot configurations. Single-loop knots of smaller-diameter wires less than 1 mm had similar or lower initial tension, initial stiffness, and yield load than a twist knot. Owing to the variance in mechanical properties, the clinical application of the knot type should depend on the diameter of the cerclage wire.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.2
• /
• pp.269-275
• /
• 1990

Nonaxisymmetric bifurcation behaviours of composite tubes two different materials subjected to uniform radial shrinkage at the external surface have been investigated and compared with those of single tube. The effect of material parameters normalized with respect to those of outer tube upon the bifurcation point and corresponding mode has been clarified. The parameters substantially affect the bifurcation mode with long-wavelength so that the composite tube with low hardening exponent or with high yield stress of inner tube destabilizes the overall deformation of the tube. However surface type bifurcation, short-wavelength mode, shown on the traction-free inner surface is hardly affected by the material parameters. The surface type bifurcation completely depends on the material characteristics of inner tube and the bifurcation point of composite tube almost coincides with the of single tube.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.7
• /
• pp.359-363
• /
• 2006

Single-walled carbon nanotubes (SWCNTs) with few defects and very small amount of amorphous carbon coating have been synthesized by catalytic decomposition of methane in $H_2$ over well-dispersed metal particles supported on MgO. The yield of SWCNTs was estimated to be 88.5% and the purities of SWCNTs thus obtained were more than 90%. Peak of the radial breathing mode in the Raman spectrum demonstrated that the diameters of synthesized CNTs are in the range 0.4-2.0 nm. Our results also indicated that MgO support materials are useful to a large-scale synthesis of high-quality SWCNTs. Increasing temperature could remarkably increase the yield and also improve the quality of SWCNTs from catalytic decomposition of methane. The morphologies and microstructures of the synthesized carbon materials were characterized by scanning electron microscopy (SEM), Thermogravimetric analysis (TGA), Raman spectroscopy, and X-ray diffraction (XRD).

• ETRI Journal
• /
• v.24 no.5
• /
• pp.341-348
• /
• 2002

We propose an asymmetric sampled grating laser and a multi-wavelength laser array associated with it. Asymmetric sampling periods combined with an index shifter make it possible to use first order reflection for lasing operations. With the structure of our design, we achieved a simple fabrication procedure as well as a high yield without using complex and time-consuming e-beam lithography for multi-period gratings. We analyzed the effect of mirror coating by numerical analysis to improve single mode and power extraction performance. By using high reflection-antireflection coatings, we obtained high power extraction efficiency without degradation of the single mode property. For the multi-wavelength laser array, to gain wavelength control, we varied the sampling periods from one laser to an adjacent laser across the array. With this approach, we showed the feasibility of an array of up to 30 channels with 100 GHz wavelength spacing.

• Earthquakes and Structures
• /
• v.3 no.2
• /
• pp.141-168
• /
• 2012

The Retrofit Yield Spectrum (RYS) is a new spectrum-based device that relates seismic demand of a retrofitted structure with the fundamental design parameters of the retrofit. This is obtained from superposition of Yield Point Spectra with design charts that summarize in pertinent spectrum-compatible coordinates the attributes of a number of alternative retrofit scenarios. Therefore, once the requirements for upgrading a given structure have been determined, the RYS enable direct insight of the sensitivity of the seismic response of the upgraded structure to the preliminary design decisions made while establishing the retrofit plan. By virtue of their spectrum-based origin, RYS are derived with reference to a single mode of structural vibration; a primary objective is to control the contribution of this mode in the retrofit design so as to produce a desirable distribution of damage at the ultimate limit state by removing soft storey formations and engaging the maximum number of structural members in deformation, in response to the input motion. Calculations are performed with reference to the yield-point, where secant stiffness is proportional to the flexural strength of reinforced concrete members. Derivation and use of the Retrofit Yield Spectra (RYS) refers to the seismic demand expressed either in terms of spectral acceleration, spectral displacement or interstory drift, at yield of the first storey. A reinforced concrete building that has been tested in full scale to a sequence of simulated earthquake excitations is used in the paper as a demonstration case study to examine the effectiveness of the proposed methodology.

• Microbiology and Biotechnology Letters
• /
• v.22 no.1
• /
• pp.80-84
• /
• 1994

In order to induce the rapid alcohol fermentation through the increases of the cell density in a continuous alcohol fermentation of naked barley, the single-cultivation with S. cerevisiae IS-019(SCM, ordinary control), mixed-cultivation with Saccharomyces uvarum IS-026 having a flocculent ability and S. cerevisiae IS-019(MCM), and mash recirculation by single-cultivation of S. cerevisiae IS-019(MRM) modes were investigated. The cell mass in the mixed-cultivation mode was about 10% higher than that of ordinary control but the final alcohol yield was slightlyl decreased. When recycled the mash with the flow rate of 7 l/h from V$_{6}$ to V$_{5}$ fermentors under the ordinary control, the cell density was distributed at 140~170$\times $10$^{6}$ cell/ml depending upon the fermentorsorders, higher about 20% than that of the ordinary control. Under these conditions the alcohol productivity of the maximum and the overall was 12.16 g/l$\cdot $h with an alcohol of 7.6% at the V$_{5}$ fermentor and 1.19 g/l$\cdot $h with an alcohol of 8.94%, respectively. For higher cell mass it was more effective to apply the mash recirculation mode with the single-cultivation of S. cerevisiae IS-019 in a pilot scale multi-stage CSTR.

• Journal of Korea Foundry Society
• /
• v.37 no.6
• /
• pp.199-206
• /
• 2017

In this study, the variations of microstructures and tensile properties of Ti-(44-54)at.%Al binary alloys were investigated. The heat-treated microstructure depended greatly on their solidification structure and annealing temperature. We measured the variations of volume fractions of primary and secondary lamellar structure as a function of the heat treatment temperature in a Ti-47at.%Al alloy. The variation of ductility as a function of Al content was in good agreement with the change of fracture mode in the tensile fracture surface. It can be inferred that the variations of yield stress and hardness of ${\gamma}$ phase in a single ${\gamma}$-phase field region are enhanced by anti-site defects created by deviations from the stoichiometric composition. In a Ti-47at.%Al alloy within the (${\alpha}_2+{\gamma}$) two-phase field, the yield stress tended to be the maximum at a near equal volume fraction of lamellar and ${\gamma}$ grains. The ductility depended sensitively on the overall grain size and Al content. The calculation of fracture strain using Chan's model indicated that the change of ductility as a function of annealing temperature was primarily determined by the variations in the overall grain size and lamellar volume fraction.