• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.292-297
• /
• 2003

A diode-pumped single-mode Nd:YV $O_4$ green laser was developed. Frequency doubling of the laser was achieved by using an intracavity KTP generated green beam (532 nm). By comparing the diode laser spectrum with absorption spectrum of the Nd:YV $O_4$ crystal, we found optimal operating temperature of the diode laser. From output power measured for various mirror curvatures and cavity lengths, we found the optimal matching of TE $M_{00}$ mode with the pump beam gives the best efficiency. When the pump power was 1.9 W, 80 ㎽ of TE $M_{00}$ mode green beam was obtained. We tried to get a single longitudinal mode lasing as the fluctuation of the laser power was caused by the shift of longitudinal modes and the beating between the modes. We tested the intracavity etalon method and birefringent filter method for single mode operation. The etalon method resulted in the best single mode output power of 60 ㎽. The power fluctuation of the single-mode laser was reduced to 1/10 of that of the multi-mode laser.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.663-664
• /
• 2006

In the electronic, medical, aerospace and automobile industries, many products and parts are manufactured by joining. Recently, as these get smaller, micro joining is becoming more and more important. In this study, micro wire-to-micro wire parallel joining was performed using single mode fiber laser. Maximum power of the fiber laser is 100 W. The CCD(Charge- Coupled Device, CCD) camera to observe the specimen was made up. The objective was applied to micro joining system to make a small spot size of laser beam. In order to control the target position, micro-multi-axis-stage was set up. This paper presents results for the single mode fiber laser joining of micro wires.

• Korean Journal of Optics and Photonics
• /
• v.20 no.6
• /
• pp.339-345
• /
• 2009

The high power and single mode vertical cavity surface emitting laser(VCSEL)s with photonic crystal structures have been proposed and fabricated by reducing substantially the hole numbers used in the photonic crystal structures. It is found that only six holes enable VCSELs to operate a single mode and the reliability can be enhanced by filling the holes with polyimide. The single mode lasing characteristics were analyzed by varying the oxide aperture and the hole diameter in photonic crystal structures. As a result, the single mode lasing can be stably obtained in the photonic crystal vertical cavity surface emitting lasers.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.6
• /
• pp.260-264
• /
• 2002

We developed LD Pumped Nd:$VVO_4$ microchip laser with the cavity length of 1mm. The microchip laser output was 87.5㎽ at the wavelength of 1063.9nm with the input power of 241㎽ at the wavelength of 809nm. The slope efficiency was 40.7% and the threshold input power was 31.1㎽. We have also defined input power limit for the single longitudinal mode operation theoretically. It was 2.5 times larger than that of threshold input intensity. According to the results of simulation, the Nd:YVO$_4$ microchip laser can be operated with the maximum output of 15㎽ for the single longitudinal mode up to the input power of 77.75㎽.

• Korean Journal of Optics and Photonics
• /
• v.6 no.4
• /
• pp.296-301
• /
• 1995

A single-mode erbium-doped fiber laser is constructed by using a intracore fiber Bragg grating and a unidirectional fiber loop mirror. The laser cavity is designed in such a way that the laser beam forms a travelling wave in the gain medium by placing the erbium-doped fiber inside the unidirectional loop and that the wavelength-selective feedback is made from the outside of the loop by a fiber grating with 0.2 nm reflection linewidth. An additional fiber ring resonator is constructed and used as an optical spectrum analyzer to observe the variation of the laser mode spectra. As the result, relatively stable single mode, single polarization output is observed for the most of the time except some mode hoppings in minute scale due to enviommental temperature variations. tions.

• ETRI Journal
• /
• v.30 no.3
• /
• pp.480-482
• /
• 2008

A novel InGaAsP/InP buried-ridge waveguide laser diode structure is proposed and demonstrated for use as a single-mode laser. The lateral mode of the proposed device can be controlled by adjusting the composition and thickness of the InGaAsP layer grown over the active region. Stable single-mode operation without kinks or beam-steering is achieved successfully with lateral and transverse in the junction plane even for the device with the ridge width of 9 ${\mu}m$ up to an injection current of 500 mA.

• Journal of the Optical Society of Korea
• /
• v.15 no.1
• /
• pp.56-60
• /
• 2011

We demonstrate passive mode-locking of a Cr:forsterite laser with a single-walled carbon nanotube saturable absorber mirror (SWCNT-SAM). Without compensation of intra-cavity dispersion, the self-mode-locked laser generates 11.7 ps pulses at a repetition rate of 86 MHz. The dispersion-compensated laser yields ultrashort pulses as short as 80 fs near $1.25\;{\mu}m$ at 78 MHz with average output powers up to 295 mW, representing the highest power ever reported for mode-locked solid-state lasers based on saturable absorption of SWCNTs in this spectral region.

• Advances in nano research
• /
• v.15 no.1
• /
• pp.25-34
• /
• 2023

This paper investigates the dynamics and stability of steady states in a continuous and discrete-time single-mode laser system. By using an explicit criteria we explored the Neimark-Sacker bifurcation of the single mode continuous and discrete-time laser model at its positive equilibrium points. Moreover, we discussed the parametric conditions for the existence of period-doubling bifurcations at their positive steady states for the discrete time system. Both types of bifurcations are verified by the Lyapunov exponents, while the maximum Lyapunov ensures chaotic and complex behaviour. Furthermore, in a three-dimensional discrete-time laser model, we used a hybrid control method to control period-doubling and Neimark-Sacker bifurcation. To validate our theoretical discussion, we provide some numerical simulations.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.56-63
• /
• 2014

To develop and understand dissimilar metals joining of Stainless steel and Copper, ultra-high speed laser lap welding was studied using single mode fiber laser in this study. SUS304 and Cu have large differences in materials properties, and Cu and Fe have no intermetallic compounds by typical binary phase of Cu and Fe system. In this study, ultra-high speed lap welds of SUS304 and Cu dissimilar metals using single-mode fiber laser was generated, and weldability of the weld fusion zone was evaluated using a tensile shear test. To understand the phenomenon of tensile shear load, weld fusion zone of interface weld area and fracture parts after tensile shear test were observed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) analysis system. And it was confirmed that Cu was easily melting and penetrating in the grain boundaries of SUS304 because of low melting temperature. And high thermal conductivity of copper occurred dissipate heat energy rapidly. These properties cause the solidification cracking in weld zone.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.851-856
• /
• 2003

This paper proposes a single-mode Lamb-wave generation and detection system using a pulsed laser as a generator and an air-coupled transducer combined with the wavelet transform analysis, as the detector. The laser source with arrayed linear slits was used to generate Lamb-wave which is able to control the wavelength of Lamb-wave to be generated by changing the slits separation. An ari-coupled transducer was used to receive Lamb-wave, which can selectably receive a single mode of leaky Lamb wave by changing the oblique angle of transducer, since the leaky Lamb-wave has unique leaky-angle according to the mode. Also, the received signal was processed by wavelet transform for the analysis in domain of time-frequency. The theoretical dipersion curve and the experimetal result was compared to show good agreement.