• 한국안전학회지
• /
• 제8권2호
• /
• pp.23-29
• /
• 1993

In this study, the method of deciding simulation test conditions is developed by computer program compared to actual vehicle test as accurately as possible. These results of analytical test conditions are conformed by simulation test using the brake dynamometer by comparison with test results of actual vehicle. Results of simulation test by these analytical results show good agreement with the vehicle test results. The analytical simulation test conditions provide the input data to brake dynamometer which follows : - each test inertia corresponding to braking deceleration - test condition of input control : brake line pressure - test condition of output control : braking torque

• 한국도로학회논문집
• /
• 제15권5호
• /
• pp.21-29
• /
• 2013

PURPOSES: Simulation of aggregate slump test using equivalent sphere particle in DEM and its validity evaluation against lab aggregate slump test METHODS : In this research, aggregate slump tests are performed and compared with DEM simulation. To utilize spheric particles in YADE, equivalent sphere diameter concept is applied. As verification measures, the volume in slump cone filled with aggregate is used and it is compared with volume in slump cone filled with equivalent sphere particle. Slump height and diameter are also used to evaluate the suggested numerical method with equivalent concept RESULTS : Simulation test results show good agrement with lab test results in terms of loose packing volume, height and diameter of slumped particle clump. CONCLUSIONS : It is concluded that numerical simulation using DEM is applicable to evaluate the effect of aggregate morphological property in loose packing and optimum gradation determination based on the aggregate slump test simulation result.

• 한국군사과학기술학회지
• /
• 제26권1호
• /
• pp.91-101
• /
• 2023

Modeling and Simulation(M&S) technology has been widely used to solve constraints such as time, space, safety, and cost when we implement the same development and test environments as real warfare environments to develop, test, and evaluate weapon systems for the last several decades. The integration and test environments employed for development and test & evaluation are required to provide Live Virtual Construction(LVC) simulation environments for carrying out requirement analysis, design, integration, test and verification. Additionally, they are needed to provide computing environments which are possible to reconfigure computing resources and software components easily according to test configuration changes, and to run legacy software components independently on specific hardware and software environments. In this paper, an Integration Test and Simulation for Engagement Control(ITSEC) bed using a bare-metal virtualization mechanism is proposed to meet the above test and simulation requirements, and it is applied and implemented for an air missile defense system. The engagement simulation experiment results conducted on air and missile defense environments demonstrate that the proposed bed is a sufficiently cost-effective and feasible solution to reconfigure and expand application software and computing resources in accordance with various integration and test environments.

• 한국해양공학회지
• /
• 제13권4호통권35호
• /
• pp.45-54
• /
• 1999

Non destructive test is applied to revise mechanical strength and assume material strength or defect of material, equipment and structure, instead of fracture test. Especially, ultrasonic test has the characteristics such as an excellent permeability high-sensitiveness to fine defect and an almost exact measurement for position, size and direction of inner defect which differ from other non destructive tests. In this study, the program is developed to evaluate optimal testing condition, to distinguish obstacle echo and defect position. This program on the basic of Ray-Tracing model shows generation and processing of ultrasonic pulse. The simulation is compared with testing in the 3 cases of an oblique angle transducer like $45^{\circ},\;60^{\circ}\;and\;70^{\circ}$. The test result for all conditions is well compared with simulation result when relative not is within $0.1{\sim}7.2%$. And the course of several echos is simply assumed through simulation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(I)
• /
• pp.210-215
• /
• 2003

Korean High Speed Train (KHST) has been tested on high speed line in JungBu site since it was developed in 2002. The KHST figured 7 cars was modeled for dynamic simulation with Vampire program. and the data acquisition system was used to test successfully the on-line test for proving the dynamic performance of KHST. The comparison between test and simulation results for dynamic behavior of KHST was tried in this paper and it was very difficult because the environmental conditions and running conditions have an effect on the test results and these conditions are unable to be modeled for dynamic analysis. Also the parameters for data acquisition system for test are usually not same to simulation conditions. Therefor, in this paper the acceleration data after filtering with low pass filter below 1Hz were used to compare between test and simulation results because the low frequency range is useful to evaluate the dynamic performance for railway vehicle system, so as steady state curving acceleration. The results show that both are similar in low frequency range.

• 한국전자파학회논문지
• /
• 제29권6호
• /
• pp.457-463
• /
• 2018

이 논문에서는 실제 레이다를 이용하여 획득한 신호와 시뮬레이션으로 획득한 신호에 ${\Sigma}{\Delta}-STAP$ 알고리즘을 적용하여 비교하였다. 시험은 무반향 챔버에서 모의신호 발생장치를 이용한 표적 신호와 신호발생기를 이용한 클러터 신호를 레이다로 수신하여 수행하였다. 시뮬레이션은 시험과 동일한 레이다 파라미터에 이상적인 기저대역 신호 모델링을 통하여 수행하였다. 비교 결과, ${\Sigma}{\Delta}-STAP$ 처리된 거리-도플러 맵은 표적 신호의 형태나 잡음 수준이 시뮬레이션과 시험 결과가 거의 유사하였다. SINR 손실의 경우, 두 결과가 비슷한 양상을 보이나, 시뮬레이션 결과가 1~2 dB 가량 높은 값을 보였다. 이를 통하여 일반적인 레이다 신호 시뮬레이션을 수행하여도 실제 시험 결과와 유사한 ${\Sigma}{\Delta}-STAP$ 처리 결과를 얻을 수 있음을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제54권5호
• /
• pp.973-986
• /
• 2015

Ethylene tetrafluoroethylene (ETFE) foil is a novel structural material which has being used in shell and spatial structures. This paper studies biaxial creep property of ETFE foil by creep tests and numerical simulation. Biaxial creep tests of cruciform specimens were performed using three stress ratios, 1:1, 2:1 and 1:2, which showed that creep coefficients in biaxial tension were much smaller than those in uniaxial one. Then, a reduction factor was introduced to take account of this biaxial effect, and relation between the reduction factor and stress ratio was established. Circular bubble creep test and triangle cushion creep test of ETFE foil were performed to verify the relation. Interpolation was adopted to consider creep stress and reduction factor was involved to take account of biaxial effect in numerical simulation. Simulation results of the bubble creep test embraced a good agreement with those measuring ones. In triangle cushion creep test, creep displacements from numerical simulation showed a good agreement with those from creep test at the center and lower foil measuring points.

• Smart Structures and Systems
• /
• 제22권6호
• /
• pp.643-662
• /
• 2018

One of the methods for investigation of mechanical behavior of materials is numerical simulation. For simulation, its need to model behavior is close to real condition. PFC is one of the rock mechanics software that needs calibration for models simulation. The calibration was performed based on simulation of unconfined compression test and Brazilian test. Indeed the micro parameter of models change so that the UCS and Brazilian test results in numerical simulation be close to experimental one. In this paper, the effect of four micro parameters has been investigated on the uniaxial compression test and Brazilian test. These micro parameters are friction angle, Accumulation factor, expansion coefficient and disc distance. The results show that these micro parameters affect the failure pattern in UCS and Brazilian test. Also compressive strength and tensile strength are controlled by failure pattern.

• 한국컴퓨터정보학회논문지
• /
• 제25권9호
• /
• pp.193-201
• /
• 2020

본 연구에서는 Test-and-Set 알고리즘을 수행하는 시뮬레이션 앱을 개발하였다. Test-and-Set 알고리즘은 고난이도 알고리즘이라 이를 이해하기 어려워하는 학습자들을 위하여 이 시뮬레이션 앱을 만들었다. 본 시뮬레이션 앱을 이용하여 Test-and-Set 알고리즘의 이해를 원하는 학습자들이 모여 팀을 이루고 논의하며 실습을 할 수 있도록 하였으며, 이런 여러 팀들이 동시에 실습할 수 있도록 만들었다. 구성한 시뮬레이션 앱에서 기계어 명령어라고 가정한 Test-and-Set 명령어를 큐를 이용하여 인터럽트 받지 않게 구성하였으며, 임계영역 문제에서 해결해야 하는 '상호배제', '진행', '제한된 대기'의 3조건이 모두 잘 수행됨을 볼 수 있었다.

• International Journal of Automotive Technology
• /
• 제6권4호
• /
• pp.351-357
• /
• 2005

Development of a real-time simulation model for high-speed and multibody tracked vehicles is difficult because they involve hundreds of highly nonlinear equations. In the development of a reliable tracked vehicle model for real-time simulation, it is helpful to use an off-line tracked vehicle model developed by considering all the degrees of freedom of each element. This paper presents a step-by-step procedure for the development of a real-time simulation model based on the off-line tracked vehicle model. The road input data, Profile IV, is used for the real time simulation and simulation results are compared with vehicle test results obtained in the military test field. It is noted that the simulation results are quite close to the test results.