• 한국자동차공학회논문집
• /
• 제17권1호
• /
• pp.114-119
• /
• 2009

The authors have investigated the NVH problems of drive system in full vehicle test. However it is difficult to define the NVH problems of driveline system. Since it is hard to measure the rotating part and it is vague that only the drive system induces the NVH problem. Vibration in a driveline is presented in this paper. In the experiment, the rear sub-frame and propeller shafts and axle were composed and mounted with rubber each other. For applying the vibration input instead of the torsional vibration effect of an engine, the shaker was taken. In particular, torsional vibration due to fluctuating forced vibration excitation across the joint between driveline and rear sub-frame was carefully examined. Accordingly, the joint response was checked from experiments and the FE-simulation using FRF (frequency response function) analysis was performed. All test results were signal processed and validated against numerical simulations. In present study, the new test bench for measuring the vibration signal and simulating the vehicle chassis system was proposed. The modal value and the mode shape of components were analyzed using the CAE model to identify the important components affecting driveline noise and vibration. It could be reached that the simplified test bench could be well established and be used for design guide and development of the vehicle chassis components.

• 기술혁신학회지
• /
• 제14권3호
• /
• pp.578-598
• /
• 2011

본 논문은 차세대 그린에너지원으로 주목받고 있는 태양광산업의 핵심소재 기술에 대한 가치를 실물 옵션 기법을 이용하여 추정한다. 본 논문의 기여는 두 가지이다. 하나는 방법론적인 기여로서, 실물옵션의 기초자산 불확실성을 대변하는 변수로서 주가를 고려하여 실물옵션 적용에서 가장 복잡한 단계인 기초자산 불확실성의 모형과정을 대폭 단순화시켰다. 다른 하나는 응용장의 기여로서, 최근 수요가 크게 증가하고 있는 태양광산업의 핵심소재인 폴리실리콘의 생산공정 기술의 경제적 가치를 평가하였다. 분석사례인 폴리실리콘 산업의 A기업에 적용한 결과, 동 기업의 폴리실리콘 기술의 기초자산이 기하브라운모션을 따르는 것으로 나타났으며 이러한 결과에 블랙-숄즈 옵션가격결정모형을 적용하여 A기업의 폴리실리콘 기술에 대한 콜옵션의 가치는 약 34,229억원으로 측정되었다.

• 접착 및 계면
• /
• 제5권2호
• /
• pp.14-26
• /
• 2004

For reliable determination of mechanical characteristics of adhesively bonded joints used e.g. as input data for computer-aided design of complex components, the thick-adherend tensile-shear test according to ISO 11003-2 is the most important material testing method. Although the total displacement of the joint is measured across the polymer layer directly in the overlap zone in order to minimize the influence of the stepped adherends, the substrate deformation must be taken into account within the framework of the evaluation of the shear modulus and the maximum shear strain, at least when high-strength adhesives are applied. In the standard ISO 11003-2 version of 1993, it was prescribed to perform the substrate deformation correction by means of testing a one-piece reference specimen. The authors, however, pointed to the excessive demands on the measuring accuracy of the extensometers connected with this technique in industrial practice and alternatively proposed a numerical deformation analysis of a dummy specimen. This idea of a mathematical correction was included in the revised ISO 11003-2 version of 2001 but in the simplified form of an analytical method based on Hooke's law of elasticity for small strains. In the present work, it is shown that both calculation techniques yield considerably discordant results. As experimental assessment would require high-precision distance determination (e.g. laser extensometer), finite element analyses of the deformation behavior of the bonded joint are performed in order to estimate the accuracy of the obtained substrate deformation corrections. These simulations reveal that the numerical correction technique based on the finite element deformation modeling of the reference specimen leads to considerably more realistic results.

• 한국전자파학회논문지
• /
• 제9권5호
• /
• pp.648-658
• /
• 1998

본 논문에서는 PCB (printed circuit board) 접지면에 셜치된 캡(gap)이 불요전자파 방사에 미치는 영향을 정 량적으로 해석하였다. 본 연구의 해석법으로 복잡한 구조체의 전자기적 특성을 해석하는데 주파수영역 전자파 수치해석 방법들과 비교하여 여러 가지 장점올 가지는 시간영역 해석법인 FDTD(finite difference time dom main) 방법올 사용하였다. 해석 구조체는 일반적으로 생산되는 PCB와 유사한 크기를 선정하였으며 소자충은 전압원과 마이크로스트립만이 폰재하는 단순화된 구조이다. PCB 접지변에 설치된 캡에 의해 생기는 인덕턴스 의 크기와 입출력 케이블올 통한 불요전자파 방사량을 FCC 및 CISPR 규정치와 함께 제시하였으며 갱의 크기 에 따라 방사되는 불요전자파의 세기가 크게 변화되는 것을 관찰할 수 있다. 본 논문의 해석결과는 실제 PCB 셜 계에 있어서 잘봇된 캡의 설치로 인한 불요전자파 방사를 막는데 유용하게 사용될 수 있으리라 생각된다.

• 대한조선학회논문집
• /
• 제45권6호
• /
• pp.710-718
• /
• 2008

This paper presents a simple and fast approach to plan the arrangement of supports and to do a ship docking analysis. The unpredicted structural damages often happen from a docking works as the size of ships are getting larger and larger. In docking a ship, excessive reaction forces from supports are primary causes of the structural damage. The grillage analysis method is employed to simply calculate only the reaction forces at supports. The grillage modeling strategies are proposed to improve the accuracy. In this paper, the results obtained by the proposed approach are compared with those of the current whole-ship FEA for typical types of ships. Comparison shows that the results from the present grillage approaches are reasonably in a good agreement with the 3-D full F.E one. Finally, an integrated program developed for the ship docking analysis is described.

• International Journal of CAD/CAM
• /
• 제7권1호
• /
• pp.71-80
• /
• 2007

Recently, feature-based solid modeling systems have been widely used in product design. However, for engineering analysis of a product model, an ed CAD model composed of mid-surfaces is desirable for conditions in which the ed model does not affect analysis result seriously. To meet this requirement, a variety of solid ion methods such as MAT (medial axis transformation) have been proposed to provide an ed CAE model from a solid design model. The algorithm of the MAT approach can be applied to any complicated solid model. However, additional work to trim and extend some parts of the result is required to obtain a practically useful CAE model because the inscribed sphere used in the MAT method generates insufficient surfaces with branches. On the other hand, the mid-surface ion approach supports a practical method for generating a two-dimensional ed model, even though it has difficulties in creating a mid-surface from some complicated parts. In this paper, we propose a dimension reduction approach on solid models based on the midsurface abstraction approach. This approach simplifies the solid model by abbreviating or removing trivial features first such as the fillet, mounting, or protrusion. The geometry of each face is replaced with mid-patches from the simplified model, and then unnecessary topological entities are deleted to generate a clean ed model. Also, additional work, such as extending and stitching mid-patches, completes the generation of a mid-surface model from the patches.

• International Journal of Railway
• /
• 제2권3호
• /
• pp.118-123
• /
• 2009

Railway track alignment Standards set a minimum lenght value for straight and circular alignments (art. 5.2.9.), in order to ensure passenger ride comfort in railway vehicles of which dynamic oscillations will thus have to be limited. The transitions between alignments can cause abrupt changes (usually called discontinuities or singular points of the alignment) of curvature, of rate of change of curvature or of rate of change of cant. A passenger is likely to experience effects due to the excitation of the elastic suspension of the vehicle which generates oscillations that are damped as the vehicle moves away from the singularity. The amplitude of these oscillations should be adequately attenuated by the damping of the suspension system within the interval between two successive singular points, especially to avoid resonances. Therefore minimum lengths between two successive singular points are stated in alignment standards. Nevertheless, these nonnative values can be overly conservative in some cases. As an alternative, track alignment designers could try to assess how much the excitation has been attenuated between two successive singular points and thus assess at which point a new singularity may be present without affecting ride comfort. Although such assessment can be made with commercial SW packages which simulate the dynamic behavior of a vehicle considered as a set of rigid bodies interconnected with elastic elements simulating the suspension systems (such as SIMPACK, ADAMS or VAMPIRE), a simplified and user-friendly computation method (based upon the analytical solution of differential equations governing the phenomenon) is made available in this paper to track design engineers, not always used to working with full dynamic models.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.1
• /
• pp.535-540
• /
• 2006

The relationship between the observable noise model and the satellite elevation angle can be modeled quite well by an exponential function.[Jin, 1996] Noise size and dependence on the elevation angle are, however, different for each observation and receiver type. Therefore, the coefficient determination of this model is an issue, and various methods including PR-CP, single difference, and time difference have been suggested. The limitations of them are difficulty to model the carrier phase noise and to eliminate bias. To overcome these disadvantages for using Jin's model, we suggest zero baseline double difference (DD) and noise sorting algorithm. Data DD technique in zero baseline is useful to eliminate all the troublesome GPS biases, and the remaining error is the sum of GPS measurement noises from two satellites. These DD residuals for hours should be sorted by the combination of satellite elevation angles, and then variance value of the residual for each combination can be estimated. Using these values, we construct an over-determined linear equation whose solution is a set of noise variance for each satellite elevation angle. With 24hr Trimble 4000ssi data, we easily worked out the coefficients of the noise model not only for pseudorange but also for carrier phase. We estimated the standard deviation of the measurement DD using our model, and plotted 1 and 3 sigma lines for every epoch to verify the representation of the residual error. 63.3% of pseudorange residual and 65.9% of phase error did not exceed the 1 sigma lines. Additionally, 99.2% and 99.5% of them lied within 3sigma line. These figures prove that the Gaussian property of measurement noise, and that the suggested model by our algorithm corresponds to the observable noise information.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권6호
• /
• pp.415-424
• /
• 2004

In this paper, we introduce and investigate a new category of rule-based fuzzy inference system based on Information Granulation(IG). The proposed rule-based fuzzy modeling implements system structure and parameter identification in the efficient form of “If..., then...” statements, and exploits the theory of system optimization and fuzzy implication rules. The form of the fuzzy rules comes with three types of fuzzy inferences: a simplified one that involves conclusions that are fixed numeric values, a linear one where the conclusion part is viewed as a linear function of inputs, and a regression polynomial one as the extended type of the linear one. By the nature of the rule-based fuzzy systems, these fuzzy models are geared toward capturing relationships between information granules. The form of the information granules themselves becomes an important design features of the fuzzy model. Information granulation with the aid of HCM(Hard C-Means) clustering algorithm hell)s determine the initial parameters of rule-based fuzzy model such as the initial apexes of the membership functions and the initial values of polynomial function being used in the Premise and consequence Part of the fuzzy rules. And then the initial Parameters are tuned (adjusted) effectively with the aid of the improved complex method(ICM) and the standard least square method(LSM). In the sequel, the ICM and LSM lead to fine-tuning of the parameters of premise membership functions and consequent polynomial functions in the rules of fuzzy model. An aggregate objective function with a weighting factor is proposed in order to achieve a balance between performance of the fuzzy model. Numerical examples are included to evaluate the performance of the proposed model. They are also contrasted with the performance of the fuzzy models existing in the literature.

• 한국산학기술학회논문지
• /
• 제14권3호
• /
• pp.1040-1044
• /
• 2013

본 논문은 추운 겨울 자동차 앞면 유리에 생기는 성에를 제거하는 워셔액 가열시스템의 가열과 분사에 따른 온도변화 특성에 관한 연구이다. 지금까지 다른 연구에서는 워셔액 가열시스템에 대한 온도 변화 특성을 간단한 수학적 모델링을 통하여 분석하였으나 본 연구에서는 워셔액 가열시스템의 보다 더 최적화된 제어시스템 설계를 위해 워셔액 가열시스템의 시간에 따른 열유동 특성 변화를 전산유체해석(CFD)을 통해 파악하기로 한다. 이를 위해서 워셔액 가열시스템의 주요 부분인 히터와 워셔액에 대한 비정상상태 해석을 수행하고 워셔액 전체의 온도 변화 특성을 분석하였다. 이를 토대로 워셔액의 가열시간과 분사시 온도 특성을 파악하여 워셔액 가열시스템의 최적설계의 기본자료로 활용하도록 하였다.