• Structural Engineering and Mechanics
• /
• v.41 no.3
• /
• pp.339-348
• /
• 2012

The slope stability analysis is usually done using the methods of calculation to rupture. The problem lies in determining the critical failure surface and the corresponding factor of safety (FOS). To evaluate the slope stability by a method of limit equilibrium, there are linear and nonlinear methods. The linear methods are direct methods of calculation of FOS but nonlinear methods require an iterative process. The nonlinear simplified Bishop method's is popular because it can quickly calculate FOS for different slopes. This paper concerns the use of inverse analysis by genetic algorithm (GA) to find out the factor of safety for the slopes using the Bishop simplified method. The analysis is formulated to solve the nonlinear equilibrium equation and find the critical failure surface and the corresponding safety factor. The results obtained by this approach compared with those available in literature illustrate the effectiveness of this inverse method.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.267-280
• /
• 1997

This paper deals with the development of simplified methods to predict the creep deformation of reinforced concrete beams. The layer approach based on a degenerate kernel of compliance function in form of Dirichlet series is mentioned and a simplified analytical method derived from the equilibrium equations and compatibility conditions is proposed to overcome the sophisticated calculation procedures in the classical creep analysis. Correlation studies between analytical and experimental results and design codes are conducted with the objective to establish the validity of the proposed methods. Besides, various parameter studies are conducted with the objective to identify the effects of cracking, steel ratio and sectional shape in the creep deformation and the obtained results are discussed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.4 no.3
• /
• pp.313-321
• /
• 2012

Vibration analysis of a thin-walled structure can be performed with a consistent mass matrix determined by the shape functions of all degrees of freedom (d.o.f.) used for construction of conventional stiffness matrix, or with a lumped mass matrix. In similar way stability of a structure can be analysed with consistent geometric stiffness matrix or geometric stiffness matrix with lumped buckling load, related only to the rotational d.o.f. Recently, the simplified mass matrix is constructed employing shape functions of in-plane displacements for plate deflection. In this paper the same approach is used for construction of simplified geometric stiffness matrix. Beam element, and triangular and rectangular plate element are considered. Application of the new geometric stiffness is illustrated in the case of simply supported beam and square plate. The same problems are solved with consistent and lumped geometric stiffness matrix, and the obtained results are compared with the analytical solution. Also, a combination of simplified and lumped geometric stiffness matrix is analysed in order to increase accuracy of stability analysis.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.759-767
• /
• 2009

Recently, there is a trend to introduce a reliability approach to the design of al large scale improvement of weak ground due to the uncertainty of the influence factors in the consolidation. Since the reliability analysis is not easily adopted to geotechnical engineers because of some difficulties in working up the theories, Duncan(2000) proposed a simplified method for using reliability method to goetechnical problems. In this study, the applicability of Duncan's simplified reliability approach is evaluated by comparing the traditional reliability results with Duncan's. In the sensitivity analysis, the two results were quite similar. However, the probability of failure showed an error range of 20~50% and further Duncan's approach could not make a distinction for the distribution of geotechnical random variables. The simplified reliability method seems to be used properly in preliminary design if it is used supplementary with the deterministic method.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.17-19
• /
• 2005

To achieve high productivity of assembly hull blocks, it is important to predict welding deformations accurately and to apply these data to the production planning. In the deformation analysis of hull block, simplified methods (elastic analysis) such as inherent method, equivalent loading method and local & global approach are usually used instead of thermal-elastic-plastic analysis because of calculating time and cost. To be much more practical, these simplified methods should consider gravity effect of plate and contact condition between the plate and the positioning jig. In this research, using finite element method, practical predicting method for the welding deformation of the curved hull blocks with considering welding sequence, gravity effect and contact condition is proposed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.457-462
• /
• 2009

In this study, seismic analysis is performed using simplified method, analytical solution and numerical analysis based on one-dimensional seismic site response analysis. The results show that analytical solution of tunnel response is predicted more conservative than numerical solution. And simplified method is not appropriate for seismic analysis of tunnel response. In addition, it is reasonable to determine shear-modulus reduction ratio performing seismic site response analysis to consider ground nonlinear-behavior.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.10
• /
• pp.1661-1666
• /
• 2003

The purpose of this study is to develop the simplified model of the crankshaft in the large marine engine for dynamic analysis. Because the actual engine system is under complex dynamic loading condition and it has multi-cylinder, the dynamic analysis is purchased at a high computation cost. In spite of this burden, the dynamic analysis must be perfonned to assure structural integrity of operating marine engine. Therefore, simplification of the analytic model is necessary for dynamic analysis. Beam-mass model, which is generated with the section property method, is the model simplified effectively. Section property method can provide desired section information by optimization technique. By applying beam-mass model to the crankshaft in the large marine engine, the usefulness of the proposed method was proven.

• Structural Engineering and Mechanics
• /
• v.71 no.2
• /
• pp.119-129
• /
• 2019

Optimum shape and length of laterally loaded piles can be obtained with different optimization techniques. In particular, the Fully Stress Design method (FSD) is an optimality condition that allows to obtain the optimum shape of the pile, while the optimum length can be obtained through a transversality condition at the pile lower end. Using this technique, the structure is analysed by finite elements and shaped through the FSD method by contemporarily checking that the transversality condition is satisfied. In this paper it is noted that laterally loaded piles with optimum shape and length have some peculiar characteristics, depending on the type of cross-section, that allow to design them with simple calculations without using finite element analysis. Some examples illustrating the proposed simplified design method of laterally loaded piles with optimum shape and length are introduced.

• Structural Engineering and Mechanics
• /
• v.68 no.6
• /
• pp.647-660
• /
• 2018

The Incremental Dynamic Analysis (IDA) procedure is currently known as a robust tool for estimation of seismic collapse capacity. However, the procedure is time-consuming and requires significant computational efforts. Recently some simplified methods have been developed for rapid estimation of seismic collapse capacity using pushover analysis. However, a comparative review and assessment of these methods is necessary to point out their relative advantages and shortcomings, and to pave the way for their practical use. In this paper, four simplified pushover analysis-based methods are selected and applied on four regular RC intermediate moment-resisting frames with 3, 6, 9 and 12 stories. The accuracy and performance of the different simplified methods in estimating the median seismic collapse capacity are evaluated through comparisons with the results obtained from IDAs. The results show that reliable estimations of the summarized 50% fractile IDA curve are produced using SPO2IDA and MPA-based IDA methods; however, the accuracy of the results for 16% and 84% fractiles is relatively low. The method proposed by Shafei et al. appears to be the most simple and straightforward method which gives rise to good estimates of the median sidesway collapse capacity with minimum computational efforts.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.67-75
• /
• 2016

In this paper, a pressure-time history curve of blast load and Conwep model are presented, and a simplified blast load formula is suggested. Generally, a blast load are applied as a pressure-time history curve, and it is calculated by blast load formula such as Conwep model. The Conwep model which is used in most of the blast analysis is quiet difficult to calculate because of its complex process. Therefore, a simplified formula is proposed to calculate blast load by simple rational expressions and to make a simplified pressure-time history curve. In this process, a curve fitting method was used to find the simple rational expressions. The calculation results of the simplified formula have an error of less than 1% in comparison with the Conwep model. And, blast analyses using finite elements method are accomplished with the Conwep model and simplified formula for verification.