• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.432-438
• /
• 1994

This paper describes the measuring method of vibration mode shapes by the Electronic Shearography. Shearographic interferometer has many merits in practical use, that is low sensitive to the environmental noisy, liw limit of the coherent-length and simple optical configuration etc.. In this study, we developed Michelson-type shearing interferometer provided with a phase stepping mirror and with a bias modulation mirror to quantify the vibration gradient fields. As a results of application to a simple cantilever plate vibration amplitude fields were obtained by the proper integration technique, and their exprimental results were in good agreement with those of the ESPI experiment.

• 대한기계학회논문집A
• /
• 제27권4호
• /
• pp.647-655
• /
• 2003

This paper studies the observability of calibration system with a constraint movement by a constraint operator. The calibration system with the constraint movement need only simple sensing device to check whether the constraint movements are completed within an established range. However, it yields the concern about the poor parameter observability due to the constraint movements. This paper uses the QR-decomposition to find the optimal calibration configurations maximizing the linear independence of rows of a observation matrix. The number of identifiable parameters are examined by the rank of the observation matrix, which represents the parameter observability. The method is applied to a parallel typed machining center and the calibration results are presented. These results verify that the calibration system with low-cost indicators and simple planar table is accurate as well as reliable.

• Journal of the Optical Society of Korea
• /
• 제3권1호
• /
• pp.23-26
• /
• 1999

A simple technique to measure electro-optic coefficients has been developed. It is based on rotating analyzer polarimetry. With a coaxial configuration of the optically active polarizing devices, the synchronously digitized signals are Fourier analyzed to quantitatively determine the elliptical polarization of light and, hence, the electric field induced birefringence. This technique has the advantage that it does not require waveguiding, and since it is improved from the crossed polarizer method it measures the phase retardation directly. It has been applied for the precise determination of electro-optic coefficients of uniaxial LiNbO3 single crystals. The excellent agreeement with reported values confirms its usefulness toward accurate characterization of electro-optic coefficients of unknown specimens.

• 천문학회보
• /
• 제36권2호
• /
• pp.83.2-83.2
• /
• 2011

The emergence of a magnetic flux tube (flux emergence) is a process of transporting magnetic field from the solar interior to the atmosphere. This process naturally produces bipolar structure at the surface, in which emerging field lines simply connect opposite polarities, while observations suggest that the surface distribution of magnetic field is more complicated than a simple bipole. This study is aimed at solving this apparent mismatch between the model and observations, showing how the surface distribution changes from a simple bipolar distribution to a quadrupolar-like one, where a half-turn rotation of the polarity inversion line plays an important role. We explain the physical reason of this half-turn rotation and also discuss a possible configuration of filament magnetic field in terms of the quadrupolar-like structure formed via flux emergence.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 D
• /
• pp.2337-2340
• /
• 2002

This paper presents the method of AGV(Automatic guided vehicle)'s moving environment(plane, corner, edge) recognition using SONAR sensor configuration. As for the SONAR sensor, the Crosstalk effect has been generally considered as an inevitable noisy phenomenon in the indoor environment. However, this effect can be used as a clue for classifying and localizing targets in the indoor environment if those can be controlled and used well. EERUF(error eliminate rapid ultrasonic firing) is a method for firing multiple ultrasonic sensors in mobile robot application and multi-echo mode of POLARIOD Device can reduce the Crosstalk effect. Here, Crosstalk effect was reduced using EERUF and applied to the AGV with a simple wall-following algorithm in the indoor environment. This method was tesed by a typical AGV with multi SONAR sensors in the laboratory environment.

• 한국광학회지
• /
• 제20권6호
• /
• pp.361-365
• /
• 2009

본 연구에서는 패턴 빔을 이용하여 표면이 거친 물체의 단차를 비접촉 방식으로 측정 하는 방법에 대하여 연구하였다. 본 연구에 사용된 방법은 장치가 매우 간단하고 스페클 노이지가 영상에 미치는 영향이 작아 재현성 면에서 매우 우수하였다. 특히 기준면에 문양이 없는 경우에는 기존의 자동 초점 측정 장치로는 측정하기 어려우나, 본 연구 방법에 의해 측정이 가능함을 보였다. 그리고 측정 시간이 매우 짧고 재현성이 좋으며 장치가 간단하여 산업 현장에서 응용하기 적절한 방법이다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.80-87
• /
• 2003

Micro gas turbines are designed with low turbine inlet temperature and pressure ratio. To overcome the efficiency defect of the simple cycle, adoption of the recuperator is an inevitable choice. In addition to the design performance, we should also pay attention to the off-design performance of gas turbines since they usually operate at part-load conditions for a considerable amount of the time. This study aims at analyzing off-design performance characteristics of micro gas turbines and addressing the importance of the recuperator in the part load operation. Comparative analyses have been performed to evaluate the part load performance differences among various design and operating options : simple vs recuperative cycles, single vs two shaft configurations, various operating strategies for the single shaft configuration (fuel only control, variable speed operation, variable inlet guide vane control), and current vs advanced engines. Major finding is that maintaining turbine at high level is crucial in efficient operation of micro gas turbines.

• 대한기계학회논문집A
• /
• 제30권9호
• /
• pp.1160-1165
• /
• 2006

In this paper, the 2-dimensional uniaxial force sensors array is introduced to detect the distributed force using fiber Bragg gratings. Uniaxial force transducer was designed to avoid the chirping and micro bending which degrade the performance of the sensor. The Brags wavelength shift of the sensor was estimated using the finite element analysis. Using this uniaxial force sensor, the uniaxial force sensors array $(3{\times}3)$ was fabricated, and the Performance of this sensors array was evaluated. The Presented sensors may has very simple configuration and its wiring is very simple compared with any other force sensors arrays.

• 한국정보통신학회논문지
• /
• 제4권1호
• /
• pp.115-121
• /
• 2000

입력제어신호 변형은 유연한 빔의 진동을 감소시키는 중요한 수단이다. 본 논문에서는 유한시간에서 다중 모드인 유연한 빔의 오차 진동을 제거하는 매우 단순한 입력제어신호 변형 방법을 소개한다. 제어신호는 선형 방정식의 풀이에 의해 구성되어 진다. 유한시간 동안 원하는 동작의 모터 각도는 임의의 한정된 오차 진동을 제거함으로서 도달된다. 폐루프 구성에서 모터 각도에 대한 기준입력으로서의 제어신호 사용에 대한 필요한 조건들 또한 다루게 된다. 제안된 시스템 구성의 효과는 컴퓨터 시뮬레이션을 통해 증명된다.

• Journal of Power Electronics
• /
• 제8권2호
• /
• pp.148-155
• /
• 2008

In this paper, a cost-effective PDP driving circuit using the transformer network is proposed. Compared with the previous works, the half-bridge type energy recovery circuit recovers the reactive energy not to the capacitor but to the source. A single sustain board architecture removes the blocking switches which are placed on the discharge path in parallel, thus reducing the number of devices. A simple reset circuit generates the same waveforms as the previous approaches. The circuit configuration and modified driving waveforms are compared with the previous works. The validity of the proposed simplified driver is verified through tests using a 6-inch panel.