• Journal of Biosystems Engineering
• /
• v.34 no.4
• /
• pp.260-268
• /
• 2009

As a basic study to develop a high sensitive biosensor using film bulk acoustic resonator, the mathematical model for analyzing the resonance characteristics of bulk acoustic resonator with acoustic Bragg reflectors was investigated. The simulation results due to the number of acoustic Bragg reflectors with low and high acoustic impedance materials were compared with the experimental results for 1, 2.25 and 5 MHz of PZT based bulk acoustic resonators with various acoustic Bragg reflectors. At the fabricated bulk acoustic resonator with an odd number of acoustic Bragg reflectors, low and high acoustic impedance materials in sequence under the bottom electrode showed better resonance characteristics than even number of acoustic Bragg reflectors. The changes of resonance frequencies due to the increase of number of acoustic Bragg reflectors by simulation and experiment, respectively showed approximately similar tendency but some differences in input impedance between the experiment and simulation were found. The derived mathematical model for describing the resonance characteristics of the bulk acoustic resonator with acoustic Bragg reflector will be available for analyzing the design parameters for development of biosensor using bulk acoustic resonator.

• Journal of Microbiology and Biotechnology
• /
• v.12 no.5
• /
• pp.819-825
• /
• 2002

Methanol dehydrogenase (MDH) is a key enzyme in the process of methanol oxidation in methylotrophic bacteria. However, information on MDH genes from genus Methylobacillus is limited. In this study, a 6.5-kb HindIII DNA fragment of Methylobacillus sp. SK-5 chromosomal DNA was isolated from the genomic library of the strain by using a degenerate oligonucleotide probe that was designed based on JV-terminal amino acid sequence of the MDH $\alpha$ subunit purified from the strain. Molecular analysis of the fragment revealed four tightly clustered genes (mxaFJGI) involved in the methanol oxidation. The first and fourth genes were very similar to mxaF (77% identity for nucleotides an 78% identity for amino acids) and mxaF (67% Identity for nucleotides and 68% Identity for amino acids) genes, respectively, from Methylovorus sp. SSI. Genes mxaF and mxaI encode $\alpha$ and $\beta$ subunits of MDH, respectively. The two subunits were identified from purified MDH from Methylobacillus sp. SK-5. A dendrogram constructed by comparison of amino acid sequences of MDH u subunits suggests that MxaF from Methylobacillus sp. SK-5 belongs to a subfamily cluster of MDH u subunits from $\beta$-subgroup Proteobacteria. The subfamily cluster is separated from the other subfamily that consists of $\beta$- and $\gamma$-subgroup Proteobacteria. This study provided information on mn genes from a methylotrophic bacterium in $\beta$-subgroup Proteobacteria, which would aid to better develop a gene probe to detect one-carbon metabolizing bacteria.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.5
• /
• pp.424-430
• /
• 2000

In order to develop an ultrasonic evaluation method for properties degradation of high temperature materials, a number of Cr-Mo-V steel samples were heat-treated and their damage mechanism was examined. Ultrasonic parameters such as velocity, attenuation, and more recently developed nonlinear acoustic parameter were measured. The nonlinear acoustic parameter was found to be most sensitive to material degradation mainly attributed to the precipitation of impurities in grain boundaries. When compared to the electrical resistivity results, the nonlinear parameters showed similar behavior. There existed a relatively good correlation between the nonlinear parameter and the fracture appearance transition temperature (FATT) obtained by Charpy V-notch impact test. Based on the relationship between the FATT and the fracture toughness ($K_{IC}$), correlation between the nonlinear parameter and $K_{IC}$ was established.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.7
• /
• pp.28-35
• /
• 2010

In the display industry, COG bonding method is being applied to production of LCD panels that are used for mobile phones and monitors, and is one of the mounting methods optimized to compete with the trend of ultra small, ultra thin and low cost of display. In COG bonding process, electrical characteristics such as contact resistance, insulation property, etc and mechanical characteristics such as bonding strength, etc depend on properties of conductive particles and epoxy resin along with ACF materials used for COG by manufacturers. As the properties of such materials have close relation to optimization of bonding conditions such as temperature, pressure, time, etc in COG bonding process, it is requested to carry out an in-depth study on characteristics of COG bonding, based on which development of bonding process equipment shall be processed. In this study were analyzed the characteristics of COG bonding process, performed the analysis and reliability evaluation on electrical and mechanical characteristics of COG bonding using ACF to find optimum bonding conditions for ACF, and performed the experiment on bonding characteristics regarding fine pitch to understand the affection on finer pitch in COG bonding. It was found that it is difficult to find optimum conditions because it is more difficult to perform alignment as the pitch becomes finer, but only if alignment has been made, it becomes similar to optimum conditions in general COG bonding regardless of pitch intervals.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.39-48
• /
• 2006

A laboratory investigation was conducted wherein smooth, rounded, siliceous river gravel aggregates were coated with fine-grained polyethylene, carpet co-product, or cement + styrene butadiene rubber latex and used to prepare hot mix asphalt concrete specimens. Only the coarse (+ No.4) aggregates were coated. The concept was that the coatings would enhance surface roughness of the aggregates and, thus, produce asphalt mixtures with superior engineering properties. Hot mix asphalt specimens were prepared and evaluated using several standard and non-standard test procedures. Based on experiences during the coating processes and analyses of these limited test results, the following was concluded: All three aggregate coating materials increased Hveem and Marshall stability, tensile strength, and resilient modulus(stiffness). These findings are indicative of improved resistance to rutting and cracking in hot mix asphalt pavements prepared using coated gravel aggregates in comparison to similar uncoated gravel aggregates.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.1
• /
• pp.23-30
• /
• 2014

The wear characteristics of $SiC_f$/SiC composites were evaluated according to the alignment direction of the fibers, and the elastic wave-generated friction was detected and analyzed in wearing. The friction coefficient and wear loss were similar in the longitudinal and the transverse direction of the fibers. However, these values were lower in the vertical direction of the fibers because of the brittle nature of the fiber. The friction coefficient and the wear loss were directly proportional to each other. The dominant frequencies were 58.6 kHz for monolithic SiC and 117.2 and 136.7 kHz for $SiC_f$/SiC composites, respectively.

• Korean Journal of Materials Research
• /
• v.4 no.3
• /
• pp.364-375
• /
• 1994

The microstructure of medium-carbon non-heat treated steels by air-cooling shows ferritepearlite structure. Compared to the conventional Q/T steels, the strength of these steels containing V, Nb and Ti are similar to Q/T steels. However, their toughness are inferior. In this study, the mechanical properties and microstructures of low-carbon Mo bearing steels produced by direct-quenching process were investigated. Especially, the effect of Mo on the direct-quenched steels was examined. The direct-quenched steels containing Mo were found to have higher strength and toughness. Mo seemed to be effective in producing the fine structure and dense precipitates because of decreasing transformation temperature. The best results were 1211 MPa in UTS and 127.5 J in toughness in the oil quenched 0.15C+O.llV+ 0.035Nb+ 1.81Mo steel. Compared to 0.4% C microalloyed steels, this results showed that UTS increased by 45% and toughness by 2 times.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.3
• /
• pp.325-335
• /
• 2011

This study analyzes the current educational curricula in the field of Clothing and Textiles in order to develop appropriate educational methods and courses. We reviewed the curricula offered by 58 Clothing and Textiles Departments at four-year universities in Korea. We analyzed the educational content of each curriculum by dividing all of the courses offered into eight categories. The analysis was based on the information posted on the universities' Internet websites, and the analysis was performed by using descriptive statistics. The results of this study are as follows: First, the educational courses of the Clothing and Textiles Departments are composed of, 36.2% design, 20.4% production, and 14.5% textile categories. In comparison with the results of a similar study conducted in 1999, emphases on the design, distribution, and marketing categories have increased, while the emphases on the production, apparel material, basic knowledge, and consumption science categories have decreased. Second, in the case of the apparel material category, basic knowledge of materials constituted 18.5%, the largest part of the category. The average number of units offered in the area of apparel materials by the 58 Departments was 17 units per year. The curricula were found to vary by regions of the country. The universities located in the Chungcheong region offer more textile material courses, but the universities in the Capital region offer fewer textile material courses than other regions. Departments that are affiliated with universities that emphasize Art and Design have more courses on basic knowledge, dyeing and finishing, and fabric design than other universities.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.14 no.1
• /
• pp.81-87
• /
• 1984

This study was performed to observe the secondary images and to analyse the relationships between the primary and secondary images in panoramic radiograph. Using the Moritta's Panex-EC panoramic x-ray machine and the human dry skull, the author analysed 17 radiographs which were selected from 65 radiographs of the dry skull that attached the radiopaque materials, and the attached regions of the radiopaque materials were the normal anatomical structures which were important and selected as a regions for the evaluation of the secondary images effectively. The results were as follows; 1. The cervical vertebrae showed three images. The midline image was the most distorted and less clear, and bilateral images were slightly superimposed over the posterior border of the mandibular ramus. 2. In mandible, the secondary image of the posterior border of the ramus was superimposed on the opposite ramus region, and this image was elongated from the anterior border of the ramus to the lateral side of the posterior border of the ramus. The secondary image of the condyle was observed on the upper area of the coronoid process, the sigmoid notch and the condyle in opposite side. 3. In maxilla, the posterior region of the hard palate showed the secondary image on the lower part of the nasal cavity and the medial wall of the maxillary sinus. 4. The primary images of the occipital condyle and the mastoid process appeared on the same region, and only the secondary image of the occipital condyle was observed symmetrically on the opposite side with similar shape to the primary one. 5. In the cranial base, the anatomical structures of the midsagittal portions like a inferior border of the frontal sinus, sella turcica, inferior borderr of the sphenoid sinus and inferior border of the posterior part of the occipital bone showed the simillar shape between the primary and secondary images symmetrically. 6. The petrous portion of the temporal bone showed the secondary image on the lateral side of the sella-turcica, and the secondary images of the posterior border of lesser wing, superior border of greater wing of the sphenoid bone and posterior border were observed on the anterior-superior and inferior region of the sella-turcica.

• Journal of Periodontal and Implant Science
• /
• v.24 no.1
• /
• pp.120-130
• /
• 1994

The purpose of the present investigation was to compare the effectiveness of porous hydroxyapatite (PHA) and coralline based porous calcium carbonate(PCC) as implant materials in human periodontal osseous defects. 10 adult patients having periodontitis and 2 similar angular osseous defects ${\ge}$5mm as verified by radiographic analysis and clinical probing depth ${\ge}$4mm were selected. The measurements were recorded just before surgery and after 6 month. Clinical parameters used in this study included gingival recession, pocket depth, probing attachment level, Sulcus Bleeding Index, Plaque Index, tooth mobility and bone defect depth measurements. After initial therapy, patients were treated with mucoperiosteal flap surgery. The contralateral bony defects in each patient randomly assigned to either bone graft material, one with PHA(Interpore 200) and the other with coralline based calcium carbonate(Biocoral). After 6 month both groups showed statistically significant reduction of pocket depth, Sulcus Bleeding Index, Plaque Index and significant improvement in probing attachment level. No statistically significant differences were found between the groups. There were 3.0mm or 68% of bone repair with PHA and 3.1mm, 61% with PCC. These values were likewise not significantly different. The data and clinical impression strongly suggest that both PHA and PCC are alloplastic implants with clinically apparent acceptance by the soft and hard tissue and that they can be used as bone graft materials successfully.