• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.11
• /
• pp.1065-1072
• /
• 2012

Due to its oxygen (O) content, biodiesel (BD) is advantageous in that it lowers PM emissions in CI engines. Therefore, BD is considered one of the best candidates for low temperature combustion (LTC) operation because its use can extend the regime for simultaneous reduction of PM and $NO_x$. Thus, in this study, LTC operation was realized using BD and diesel with a 5~7% $O_2$ fraction. Engine test results show that the use of BD increased the efficiency and reduced emissions such as PM, THC, and CO; furthermore, IMEP reduced by 10~12% owing to the lower LHV of the fuel. In particular, smoke was suppressed by up to 90% because O atoms in the BD enhanced the soot oxidation reaction. To compensate the IMEP loss, turbocharging (TC) was then tested, and the results showed that the power output increased and PM was reduced further. Moreover, TC in BD engine operation allowed a similar level of reduction in both $NO_x$ and PM at 11~12% $O_2$ fraction, suggesting that there is a potential to widen the operating range by the combination of TC and BD.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.12
• /
• pp.1129-1135
• /
• 2013

In this, three types of natural gas were employed to investigate the effect of low-calorific natural gas on the performance of and emissions from a heavy-duty CNG engine. The performance and emission characteristics were analyzed by conducting a full-load test, WHSC mode test, and WHTC mode test. The results showed that the torque of low-calorific natural gas with $9,800kcal/Nm^3$ of higher heating value decreased by 4.4 compared to that of the current natural gas with $10,400kcal/Nm^3$ of heating value. With low-calorific fuels, CO, $CO_2$, and $NO_x$ emissions decreased. However, THC emissions increased. According to the WHSC and WHTC mode test results, the thermal efficiency increased and the emission characteristics showed a similar trend to the full-load test results. Low-calorific natural gases cause a decrease in torque at full-load operation conditions and an increase in hydrocarbon emissions.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.223-226
• /
• 2000

The oxygen deficient ferrites $(Ni_x,\; Zn_{1-x})Fe_2O_{4-{\delta}}$ can decompose $CO_2$ as C and $O_2$ at a low temperature of about $300^{\circ}C$. Ultra powders of $(Ni_x,\; Zn_{1-x})Fe_2O_4$ for the $CO_2$ decomposition were prepared by the hydrothermal methods. The XRD result of synthesized ferries showed the spinel structure of ferrites and ICP-AES and EDS quantitative analyses showed the composition similar with the starting molar ratios of the mixed solution prior to reaction. The BET surface area of the synthesized(Ni, Zn)-ferrites was above $110\textrm{m}^2/g$ and its particle size was very as small as about 5~10 nm. The $CO_2$ decomposition efficiency of the oxygen deficient ferrites($(Ni_x,\;Zn_{1-x})Fe_2O_{4-{\delta}}$) was almost independent with composition and the $CO_2$ decomposition efficiency of ternary (Ni, Zn)-ferrites was better than of binary Ni-ferrites.

• Journal of the Korean Ceramic Society
• /
• v.42 no.1
• /
• pp.56-61
• /
• 2005

Highly durable photocatalytic paper containing anatase $TiO_{2}$, active carbon and ceramic fiber, which can adsorb VOCs and decompose them by photo oxidation simultaneously, was manufactured and characterized. Optimum concentration of PDADMAC to let $TiO_{2}$ adhere on the surfaces of active carbon and ceramic fiber selectively was $10\~15$ ppm in a slurry mixture for making photocatalytic paper. The thickness and basis weight of the produced catalytic paper by paper-making method were 0.4 mm and 380 $g/m^{2}$, respectively. Adsorption reaction by active carbon and photocatalytic decomposition reaction by $TiO_{2}$ were proceeded simultaneously, by which the abatement rate was found to be greatly enhanced compared to the similar environment with single adsorption reaction or single photocatalytic reaction only. The selective attachment of $TiO_{2}$ on ceramic fiber and active carbon was found to be very effective in preventing decomposition of substrate by the $TiO_{2}$ attack during exposure to UV light.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.334-339
• /
• 2020

In this study, the adhesion properties between aluminum and composite materials, composite materials, and composite materials were compared according to the physical surface treatment to improve mechanical bonding at the bonding surface when considering carbon fiber and glass fiber-reinforced composite materials. Bonded specimens were classified into the type of base material and the surface treatment method of the bonding surface. Sandpaper, sandblasting, and plasma were applied as physical surface treatment methods. The bonded specimen was prepared as a single lap joint test specimen. An experiment to measure the lap shear strength was conducted, and the results were compared. The experimental results confirmed that the mechanical abrasion and sandblasting treatment improved the lap shear strength approximately 4 to 5 fold compared to the general specimen without physical surface treatment. In plasma treatment, the experiment was conducted by defining the respective plasma output and treatment time as follows: 150 W and 5 minutes, 150 W and 10 minutes, and 300 W and 3 minutes. Moreover, the lap shear strength results were similar to the previous mechanical surface treatments. On the other hand, the effect on the adhesion properties was small, depending on the plasma treatment conditions.

• Journal of Conservation Science
• /
• v.36 no.3
• /
• pp.152-161
• /
• 2020

The purpose of this study was to compare the chemical properties of white soil and refined clay sediment, which are produced early in the refining process. The characteristics of the white wares made at the kiln site in Goseong-ri, Chuncheon were also examined. Three groups of materials were examined: white wares excavated from the white wares kiln, raw material from white soil collected from the surface, and a refined clay sediment group. There were also three analysis methods, which were a main components analysis, a trace components analysis, and a mineral analysis. The main components analysis found that the white wares clay was in the RO₂4.04~4.28 and the RO + R₂O 0.30~0.31 mole areas, which were similar to the results for the refined clay sediment. However, the refining process used to produce better quality white wares meant that the large differences in the early white soil raw material appeared in the refined sediment. The mineral phase analysis showed that the crystals detected in the early white soil raw materials and refined clay sediment were almost identical. However, quartz and mullite mineral phases, which can occur above a certain temperature, were detected in the excavated white wares clay. Rare earth elements that were not affected by the pottery making process and the weathering of clay materials were found to have the same origin in all three groups.

• Journal of Conservation Science
• /
• v.36 no.2
• /
• pp.112-122
• /
• 2020

The purpose of this study was to find out the correlation through comparative analysis of used materials and manufacturing techniques such as firing characteristics for sherds excavated from celadon kiln site in Punggil-ri, Jangheung. The color difference of the sherds was very wide, and even in the microstructure of the cross section of the glaze layer and the body layer, the celadons, whitewares, blackware, and stonewares could not be characterized because they did not show distinct differences from each other. As a result of estimating the firing temperature through the analysis of constituent minerals and thermal analysis, most of them were estimated to have been fired at 1000℃, but some were fired at high temperatures above 1200℃. It was difficult to clearly distinguish between celadon and whiteware even in the major compositional content of bodies. In the statistical analysis, glaze could be classified three group according to the type of sherds, but the bodies of celadons, whitewares, and blackware classified into one similar group. It is considered that it is not more likely differences in raw materials but some ingredients were removed or added during the purification process. Conclusionally, in this kiln site was found through scientific analysis that there were technical attempts to produce various ceramics, and that the manufacturing techniques and materials of ceramics were in an early stage that was not stabilized.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.473-478
• /
• 2002

${\alpha}-Al_2O_3$ platelets were synthesized by microwave heating the two different powder mixtures of $Al_2(SO_4)_3+2Na_2SO_4$ and ${\gamma}-Al_2O_3+2Na_2SO_4$ using flux method. DTA-TG, XRD and SEM were used to investigate the effect of microwave on the formation of ${\alpha}-Al_2O_3$ platelets. In the case of the mixture of $Al_2(SO_4)_3+2Na_2SO_4$, the microwave heated sample was ${\alpha}-Al_2O_3$ platelets composed of aggregates with smaller particle size compared to the conventionally heated sample. In the case of the mixture of ${\gamma}-Al_2O_3+2Na_2SO_4$, the temperature to form ${\alpha}-Al_2O_3$ platelets by the microwave heating was lower than that by the conventional heating and the morphology of the microwave heated sample was similar to that of the conventionally heated sample except that the microwave heated sample had smaller particle size compared to the conventionally heated sample.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.31 no.6
• /
• pp.478-484
• /
• 2009

Three-dimensional porous scaffolds play an important role in tissue engineering strategies. They provide a void volume in which vascularization, new tissue formation, and remodeling can occur. Like any grafted materials, the ideal scaffold for bone tissue engineering should be biocompatible without causing an inflammatory response. It should also possess biodegradability, which provides a suitable three-dimensional environment for the cell function together with the capacity for gradual resorption and replacement by host bone tissue. Various scaffolds have already been developed for bone tissue engineering applications, including naturally derived materials, bioceramics, and synthetic polymers. The advantages of biodegradable synthetic polymers include the ability to tailor specific functions. The purpose of this study was to examine the osteogenic activity of periosteal-derived cells in a polydioxanone/pluronic F127 scaffold. Periosteal-derived cells were successfully differentiated into osteoblasts in the polydioxanone/pluronic F127 scaffold. ALP activity showed its peak level at 2 weeks of culture, followed by decreased activity during the culture period. Similar to biochemical data, the level of ALP mRNA in the periosteal-derived cells was also largely elevated at 2 weeks of culture. The level of osteocalcin mRNA was gradually increased during entire culture period. Calcium content was detactable at 1 week and increased in a time-dependent manner up to the entire duration of culture. Our results suggest that polydioxanone/pluronic F127 could be a suitable scaffold of periosteal-derived cells for bone tissue engineering.

• Journal of Life Science
• /
• v.22 no.5
• /
• pp.650-656
• /
• 2012

To reduce the production cost of $Pleurotus$ $ostreatus$, discarded medicinal sludge was collected from oriental medical clinics to develop the $Pleurotus$ $ostreatus$ culture medium. According to the analysis of the proximate composition of the materials used in Korean herb medicine, the crude ash contents of $Carthamus$ $tinctrius$ L stem and $Acanthopanax$ $chiisanensis$ were 11.6% and 10.1% respectively, which were relatively higher than the 9.6% of the control medium, waste cotton. Crude protein was detected in 9.8% of the waste cotton medium, whereas it was detected in 14.9%, 13.9%, 13.4%, and 11.5%, of wild mugwort, $Acanthopanax$ $\underline{chiisanensis}$, medicinal sludge, and $Carthamus$ $tinctrius$ L stem, respectively, which are all higher than the control. The pH of medicinal sludges, wild mugwort, and $Aacanthopanax$ $chiisanenses$ ranged from 5.27 to 5.72, which was similar to the 5.70 pH value of waste cotton. In the case of addition concentration of each Korean herb medicine material influencing mycelial growth of the $Pleurotus$ $ostreatus$, the 9% concentration was more favorable compared to that of 3% and 6%. However, the addition of Korean herb medicine materials did not significantly affect the growth of $P.$ $tolaassi$ and $Trichoderma$ $sp.$ According to a field experiment that added 9% of medicinal sludge into the waste cotton medium, the mycelial growth of mushrooms was facilitated by approximately 2 days, and the mushroom yield was increased by 10~15%. Furthermore, pileus and stipe of the mushrooms were even and superior in quality.