• Korean Journal of Materials Research
• /
• v.27 no.7
• /
• pp.369-373
• /
• 2017

Unidirectionally solidified TiAl alloys were prepared by optically-heated floating zone method at growth rates of 10 to 70 mm/h in flowing argon. The microstructures and tensile properties of these crystal bars were found to depend strongly on the growth rate and alloy composition. TiAl alloys with composition of 47 and 50 at.%Al grown under the condition of 10 mm/h showed $Ti_3Al({\alpha}_2)/TiAl({\gamma})$ layer structures similar to single crystals. As the growth rate increased, the alloys with 47 and 50 at.%Al compositions showed columnar-grain structures. However, the alloys fabricated under the condition of 10 mm/h had a layered structure, but the alloy with increased growth rate consisted of ${\gamma}$ single phase grains. The alloy with a 53 at.%Al composition showed a ${\gamma}$ single phase regardless of the growth rate. Room-temperature tensile tests of these alloys revealed that the columnar-grained material consisting of the layered structure showed a tensile ductility of larger than 4 % and relatively high strength. The high strength is caused by stress concentration at the grain boundaries; this enhances the secondary slip or deformation twinning across the layered structure in the vicinity of the grain boundaries, resulting in the appreciable ductility.

• Transactions of Materials Processing
• /
• v.20 no.5
• /
• pp.362-368
• /
• 2011

For the purpose of improving crashworthiness qualities and maximizing weight saving efficiency, TWB's(tailor welded blanks) of quench-hardenable boron steel sheet formed by hot stamping processes has been used for automotive BIW (body in white) applications. In this work, the flow behaviors of TWB of quench-hardenable boron steel sheet were investigated in uniaxial tension tests at elevated temperature. TWB's having a uniform thickness of 1.4mm were fabricated by laser welding. Specimens with two weld line directions were used to test the mechanical property and reliability of the weld zone. After heating at $950^{\circ}C$ for 5min, the specimens were subjected to tension test at 650, 700 and $800^{\circ}C$ with a strain rate of 0.01 /s and at $700^{\circ}C$ with strain rates of 0.01, 0.1 and 1/s. The ultimate strength of the weld zones was higher than that of the base materials at 650 and $700^{\circ}C$, but was similar to the base metal at $800^{\circ}C$. Fracture occurred at the base material at 650 and $700^{\circ}C$, but at the weld zone at $800^{\circ}C$.

• Environmental Engineering Research
• /
• v.22 no.2
• /
• pp.149-156
• /
• 2017

Chromium(III) recovery from tanning wastewater by means of adsorption on activated carbon and elution with sulfuric acid was studied. Tests were carried out at laboratory scale on an effluent of industrial origin. Initially, proteinaceous materials and fats were separated via sieving followed by ultrafiltration. The chemical composition of the sample thus precleansed was (in g/L): 1.09 chromium(III); 10.36 sulfate; 11.10 sodium; 9.57 chloride; 0.40 proteinaceous materials; and 0.20 fats. Adsorptions were made at 20, 30, and $40^{\circ}C$, establishing what temperature favored chromium(III) uptake. At $40^{\circ}C$, the maximum cation fixation was 40.2 mg/g, and the lowest content in an equilibrium solution was 3.9 mg/L. As regards sodium, chloride, and sulfate, the concentrations before and after the treatment were similar. Likewise, it was found that protons were also retained, modifying the pH of the liquid medium. Adsorption isotherms were analyzed using the Langmuir, Temkin, and Freundlich models. Finally, the extraction of the adsorbed tanning agent with sulfuric acid was evaluated. A recovery of 96.5% was achieved with 0.9 N at $70^{\circ}C$ (13.23 g/L $Cr^{3+}$; 42.98 g/L sulfate; and 0.40 g/L NaCl).

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.2
• /
• pp.125-129
• /
• 2003

The effects of molecular structure on the redox properties of the organic electroluminescent materials (Ir$(ppy)_3$ Ir$(m-ppy)_3$ Ir$(p-toly)_3$) were studied using cyclic voltammetry and spectroscopy. These iridium complexes show reversible oxidation and reduction on the electrode, which produce the symmetric cyclic voltammogram. It indicates that these materials are very stable under repetitive oxidation/reduction cycles. The electrochemically determined ionization potentia/electron affinity values are 5.4OeV/3.02eV for Ir$(ppy)_3$, 5.36eV/2.96eV for Ir$(m-ppy)_3$, and 5.35eV/2.97eV for Ir$(p-toly)_3$ from the SCE(Standard Calomel Electrode). The electrically determined band gaps are 2.38eV (521nm), Ir$(ppy)_3$, 2.4OeV (517nm), Ir$(m-ppy)_3$, and 2.38eV (521nm). Ir$(p-toly)_3$, which are similar with the optical band gaps. The position of methyl group on 2-phenylpyridine (ppy) effects do not influence much on the ionization potential, electron affinity, and band gap of Ir$(ppy)_3$ derivatives.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.841-846
• /
• 2011

New green host materials, 9-phenyl-3-(4-(1-phenyl-1H-benzo[d] imidazol-2-yl)phenyl)-9H-carbazole (3a) and 9-(naphthyl-2-yl)-3-(4-(1-phenyl-1H-benzo[d]imidazol-2-yl)phenyl)-9H-carbazole (3b), have been designed and synthesized by attaching the electron transporting benzimidazole moiety to the hole transporting carbazole unit. These compounds have similar HOMO, LUMO levels and band-gap characteristics compared with CBP (4,4'-di(N-carbazolyl)biphenyl). The fabricated green phosphorescent OLED with this 3a host shows much better device performances compared to CBP-based one. The current and power efficiency is enhanced at least by 60 percent at a given constant luminance of 1000 cd/$m^2$.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.852-856
• /
• 2011

The lithium ion diffusion coefficients of bare, carbon-coated and Cr-doped $LiFePO_4$ were obtained by fitting the discharge curves of each half cell with Li metal anode. Diffusion losses at discharge curves were acquired with experiment data and fitted to equations. Theoretically fitted equations showed good agreement with experimental results. Moreover, theoretical equations are able to predict lithium diffusion coefficient and discharge curves at various discharge rates. The obtained diffusion coefficients were similar to the true diffusion coefficient of phase transformation electrodes. Lithium ion diffusion is one of main factors that determine voltage drop in a half cell with $LiFePO_4$ cathode and Li metal anode. The high diffusion coefficient of carbon-coated and Cr-doped $LiFePO_4$ resulted in better performance at the discharge process. The performance at high discharge rate was improved much as diffusion coefficient increased.

• Carbon letters
• /
• v.7 no.4
• /
• pp.259-265
• /
• 2006

Carbon-coated $TiO_2$ was prepared by $CCl_4$ solvent mixing method with the different heat treated temperatures (HTTs). Since the carbon layers derived from pitch on the $TiO_2$ particles were porous, the carbon-coated $TiO_2$ sample series showed a good adsorptivity. The values of BET surface areas measured were shown independently on the HTTs. The surface states by SEM present to the characterization of porous texture on the carbon-coated $TiO_2$ sample and carbon distributions on the surfaces. From XRD data, PT700 and PT750 were shown the X-ray diffraction patterns of the anatase $TiO_2$, but PT800 and PT850 were kept anatase-type structure even after heating at $800^{\circ}C$, though small amount of the rutile-type structure appears. The results of EDX microanalyses were observed for each sample show the spectra corresponding to almost all samples similar to C, O and Ti elements with an increase of HTTs. Finally, the excellent photoactivity of carbon-coated $TiO_2$ (especially, PT700 and PT750) could be attributed to the homogeneous coated carbon on the external surface and the structural anatase phase.

• Journal of the Korean Ceramic Society
• /
• v.34 no.7
• /
• pp.758-766
• /
• 1997

Non-brittle fracture behaviour of the two composite structures made of two different brittle materials was investigated using 3-point bending test. First, the layered and fibrous macro-composites were fabricated using the material easily formed, yet showing a brittle fracture behaviour similar to ceramics. The layered and fibrous Al2O3 /Al2O3 composites with weak interface were also fabricated using plate of 2 mm thickness and rod of 3 mm diameter respectively. Comparison of the mechanical properties between these two structures was performed in the lights of flexural strength and work of fracture for the composites consisting of Al2O3 and simulated materials respectively. The strength ratio of layered structure to the monolith of same volume was 0.6 and the ratio of fibrous one was about 0.2 for the composites made of simulated brittle material. The ratio of the work of fracture of the fibrous to the layered was 0.47. For Al2O3/Al2O3 composites, the strength ratio of layered and fibrous structures to the monolith with same volume were about 0.6 and 0.2 respectively. The ratio of work of fracture of the fibrous to the layered was 0.6. These confirmed that the layered structure was superior to the fibrous one in terms of flexural strength and work of fracture.

• Journal of the Korean Ceramic Society
• /
• v.43 no.10 s.293
• /
• pp.660-665
• /
• 2006

The mechanical properties of $Al_2O_3$-SiC composites manufactured with adding various amount and size of SiC particles have been measured and analyzed. Generally, the elastic modulus of the composites shows about 50% less than that of PL-8 (45 wt% $Al_2O_3$-51 wt% $SiO_2$-4 wt% other oxides), but the flexural strength is similar with each other. The impact resistance property of $Al_2O_3$-SiC composite against high velocity copper jet was lower than that of PL-8 when SiC particles of approximately 3 $\mu$m diameter was added to. It is caused probably due to the micro-pores made by oxidation of SiC particles. However, in the case of the less-weighted $Al_2O_3$-SiC composite adding to 10 wt% SiC with average diameter of 10 $\mu$m and sintering at 1200$^{\circ}C$, the impact resistance property was improved up to 37 percent compared with that of PL-8.

• Journal of the Korean Ceramic Society
• /
• v.51 no.2
• /
• pp.132-137
• /
• 2014

The study was performed with low-grade limestone, which is used to make cement or is disposed of due to its low CaO content. In this study, the optimal condition of limestone with which to manufacture precipitated calcium carbonate (PCC) and limestone in fiber was determined through in-situ reactions. The best firing condition is with slaked lime with rapid cooling after 2 h of firing at $1000^{\circ}C$. In addition, the content of CaO can be increased by sorting the low-grade limestone using a 200 mesh filter, and the optical quality of old newspaper (ONP) was similar when using both low-grade and high-grade limestone. Also, controlling the particle size of PCC is an important factor pertaining to the optical characteristics of paper.