• Geomechanics and Engineering
• /
• v.35 no.4
• /
• pp.425-436
• /
• 2023

An effective tool for researching actual problems in geotechnical and mining engineering is to conduct physical modeling tests using similar materials. A reliable geometric scaled model test requires selecting similar materials and conducting tests to determine physical properties such as the mixing ratio of the mixed materials. In this paper, a method is proposed to determine similar materials that can reproduce target properties using a polynomial model based on experimental results on modeling materials using a gypsum-sand mixture (GSM) to simulate rocks. To that end, a database is prepared using the unconfined compressive strength, elastic modulus, and density of 459 GSM samples as output parameters and the weight ratio of the mixing materials as input parameters. Further, a model that can predict the physical properties of the GSM using this database and a polynomial approach is proposed. The performance of the developed method is evaluated by comparing the predicted and observed values; the results demonstrate that the proposed polynomial model can predict the physical properties of the GSM with high accuracy. Sensitivity analysis results indicated that the gypsum-water ratio significantly affects the prediction of the physical properties of the GSM. The proposed polynomial model is used as a powerful tool to simplify the process of determining similar materials for rocks and conduct highly reliable experiments in a physical modeling test.

• Restorative Dentistry and Endodontics
• /
• v.46 no.3
• /
• pp.39.1-39.12
• /
• 2021

Objectives: This study analyzed the physical-chemical behavior of 2 bulk fill resin composites (BFCs; Filtek Bulk Fill [FBF], and Tetric-N-Ceram Bulk Fill [TBF]) used in 2- and 4-mm increments and compared them with a conventional resin composite (Filtek Z250). Materials and Methods: Flexural strength and elastic modulus were evaluated by using a 3-point bending test. Knoop hardness was measured at depth areas 0-1, 1-2, 2-3, and 3-4 mm. The translucency parameter was measured using an optical spectrophotometer. Real-time polymerization kinetics was analyzed using Fourier transform infrared spectroscopy. Results: Flexural strength was similar among the materials, while TBF showed lower elastic modulus (Z250: 6.6 ± 1.3, FBF: 6.4 ± 0.9, TBF: 4.3 ± 1.3). The hardness of Z250 was similar only between 0-1 mm and 1-2 mm. Both BFCs had similar hardness until 2-3 mm, and showed significant decreases at 3-4 mm (FBF: 33.45 ± 1.95 at 0-1 mm to 23.19 ± 4.32 at 3-4 mm, TBF: 23.17 ± 2.51 at 0-1 mm to 15.11 ± 1.94 at 3-4 mm). The BFCs showed higher translucency than Z250. The polymerization kinetics of all the materials were similar at 2-mm increments. At 4-mm, only TBF had a similar degree of conversion compared with 2 mm. Conclusions: The BFCs tested had similar performance compared to the conventional composite when used in up to 2-mm increments. When the increment was thicker, the BFCs were properly polymerized only up to 3 mm.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.24 no.1
• /
• pp.17-21
• /
• 2012

The effect of cultivation season on the cocoon filament quality of authorized silkworm variety, GoldenSilk was examined with cocoon filament character, reeling character, and fiber character during 3 years. In cocoon filament character, filament length of spring and autumn cocoon was 979 and 879 m, respectively. Cocoon filament weight of spring and autumn cocoon was 33.1 and 26.5 cg, which is lower than that of general bivoltine strain, BaeGokJam. Raw silk percentage of spring and autumn cocoon was 15.65 and 13.77%, respectively. In reeling character, reelability showed similar trend regardless of cultivation season and strain. However, the length and weight of non-broken filament of spring season were slightly higher than those of autumn cocoon. Cultivation season did not affect on the fiber characteristics such as clearness and neatness, lousiness, and degumming loss. In cocoon character, filament length, size, and weight, spring cocoon filament showed higher value than autumn cocoon, but lower than authorized general silkworm varieties. In reeling characteristics, non-broken length and weight showed the similar trends with the cocoon filament character. However, the reelability of GoldenSilk cocoon was not affected by cultivation season. The reelability of GoldenSilk cocoon was also similar with that of authorized general one. Fiber character including clearness and neatness, lousiness, and degumming loss was also similar regardless of the rearing season and different strain.

• Journal of the Korean Society of Safety
• /
• v.7 no.1
• /
• pp.65-72
• /
• 1992

Objective of this research is to evaluate fracture behaviors of fresh-butt welded metal by the acoustic emission technique. The specimens used are medium carbon steel(SM45C), mild steel (SS41) and stainless steel(SUS304), which have different weldability. The similar welding and dissimilar welding processes are considered, in the former SM45C, SS41 and SUS304 are used, in the later the following metals are used SM45C and SS41, SM45C and SUS304 and SS41 and SUS304. The characteristics of fracture in weld metal are eshmated by the tension test with nominal speciemns, the fracture toughness test with compact tension specimens and fractography analysis. The results of tension test show for base metals and similar welding materials that the yield strength and ultimate strength of similar welding materials are increased, the elongation of those are decreased. The weldability of SUS304 is better than that of SM45C and SS41 In similar welding materials. Mechanical properties of dissimilar welding mateiiths we lower than those of similar welding materials. In dissimilar welding materials, the weldability of SM45C and SUS304 is better than that of SM45C and SS41, and also weidability of SS41 and SUS304 is better than SS41 and SM45C. Comparing mechanical properties with AE counts, it is found that AE conuts appeared on a small before the limit load of elasticity(P$_{e}$), and apper greatly near yield strength region in tension test. These results could contribute to the safety analyses and the evaluation of strength for welding structure.e.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.2
• /
• pp.53-60
• /
• 2017

The aim of this study is to examine a feasibility to substitute Ti for Ta in reduced activation ferritic/martensitic (RAFM) steel by comparing a Ti-added RAFM steel with a conventional Ta-added RAFM steel. The microstructures and mechanical properties of Ta-, and Ti-added RAFM steels were investigated and a relationship between microstructures and mechanical properties was considered based on quantitative analysis of precipitates in two RAFM steels. Ta-, and Ti-added RAFM steels were normalized at $1000{\sim}1040^{\circ}C$ for 30 min and tempered at $750^{\circ}C$ for 2 hr. Both RAFM steels had very similar microstructures, that is, typical tempered martensite with relatively coarse $M_{23}C_6$ carbides at boundaries of grain and lath, and fine MX precipitates inside laths. The MX precipitates were identified as TaC in Ta-added RAFM steel and TiC or (Ti, W)C in Ti-added RAFM steel, respectively. It is believed that these RAFM steels show similar tensile and Charpy impact properties due to similar microstructures. Precipitate hardening and brittle fracture strength calculated with quantitative analysis of precipitates elucidated well the similar behaviors on the tensile and Charpy impact properties of Ta-, and Ti-added RAFM steels.

• Journal of Welding and Joining
• /
• v.12 no.3
• /
• pp.63-70
• /
• 1994

Laser processing workmen should select the working condition for laser cutting of new materials by the preparatory experiments for that material or from the past experiences in cutting of other similar materials. This paper proposes a criterion to determine how much a material is similar to other materials by using the Sugeno fuzzy integral. With the proposed criterion the laser processing workman can objectify the considered material for his decision. The expert system programmer can give the system a high flexibility by experimenting with some materials in a large range of similarity and can support the laser processing workman by offering the similarity between materials.

• Archives of Metallurgy and Materials
• /
• v.67 no.4
• /
• pp.1531-1534
• /
• 2022

In this study, a SUS316L membrane having double layered pore structures was fabricated, and the pore characteristics were analyzed after coating with a spherical powder and a flake-shaped powder on a disk-shaped SUS316L support using a wet powder spraying process. The thickness of the coated layer was checked using an optical microscope, and air permeability was measured using a capillary flow porometer. When the coating amount was similar, the fine porous layer prepared using flake powder was thicker and showed higher porosity. In the case of a similar thickness, the case of using flake powder was half of the amount of spherical powder used. Therefore, it was confirmed that it is possible to manufacture a metal membrane having a high filter efficiency even with a small coating amount when using the flake powder.

• Journal of Microbiology
• /
• v.42 no.4
• /
• pp.357-360
• /
• 2004

For determining the process of bacterial aggregation, glucose was added into water from Lake Baikal which had been stored for seven months. In the presence of a higher concentration of glucose, the abun­dance of single bacteria and aggregates were higher, but the biovolumes of both bacteria were similar. Theses results mean that both free-living and aggregated bacteria have similar maximum sizes and that aggregates are forming with available organic materials. With available organic materials, the biovol­ume of aggregates becomes larger.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1095-1098
• /
• 2004

In this study, $Bi_2O_3-B_2O_3-ZnO$ glass system, which was expected to have similar properties with PbO containing glass system, was selected as a PbO replaceable potential composition because the atomic weight and ionic radius of Bi is similar to those of Pb. Glasses with different modifier/former ratio were prepared by melting the raw ingredient mixtures in $Bi_2O_3-B_2O_3-ZnO$ system, and the thermal and electrical properties of the sintered samples were examined. The glass transition temperatures and the dielectric constant of the glass pellets were between 350 $^{\circ}C{\sim}$500 $^{\circ}C$ and 15-35, respectively.

• Journal of Ginseng Research
• /
• v.14 no.3
• /
• pp.427-431
• /
• 1990

To search for substituents of greens, several organic materials such as rice straw, barley straw, corn stem and manufactured compost were applied in a ginseng cultivating field. The yields of six year old ginseng harvested in the rice straw, barley strait and corn stem treated field were similar to or higher than that of the greens treated one. The varied amount of applied substituents resulted in a yield change, but statistical linearity was not found. The growth of ginseng aerial part and soil physicochemical property in the field fortified with these substituents showed similar results to those of the greens treated one. So, it is though that these organic materials can substitute for greens.