• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.229-235
• /
• 1991

A new electrode material for $Ta_2O_5$ capacitor was developed to obtain both high dielectric constant and improved electrical properties for use in DRAM. High leakage current and low breakdown field of as-deposited $Ta_2O_5$ film on Si is due to the reduction of $Ta_2O_5$ by silicon at $Ta_2O_5$/electrode interface. $Dry-O_2$ anneal improves the electrical properties of $Ta_2O_5$ capacitor with Si electrode, but it thickens the interfacial oxide and lowers the dielectric constant, subsequently. $Ta_2O_5$ capacitor with TiN exectrode shows better electrical properties and higher dielectric constant than post heat treated $Ta_2O_5$ film on Si. No interfacial oxide layer at $Ta_2O_5$/TiN interface suggests that there\`s no Interaction between $Ta_2O_5$ and electrode. TiN is a adequate electrode material for $Ta_2O_5$ capacitor.

• Journal of Sensor Science and Technology
• /
• v.8 no.2
• /
• pp.115-123
• /
• 1999

A micro-gas sensor with heater and sensing electrode on the same plane was fabricated on phosphosilicate glass(PSG, 800nm)/$Si_3N_4$ (150nm) dielectric membrane. PSG film was provided by atmospheric pressure chemical vapor deposition(APCVD), and $Si_3N_4$ film by low pressure chemical vapor deposition (LPCVD). Total area of the fabricated device was $3.78{\times}3.78mm^2$. The area of diaphragm was $1.5{\times}1.5mm^2$, and that of the sensing layer was $0.24{\times}0.24mm^2$. Finite-element simulation was employed to estimate temperature distribution for a square-shaped diaphragm. The power consumption of Pt heater was about 85mW at $350^{\circ}C$. Tin thin films were deposited on the silicon substrate by thermal evaporation at room temperature and $232^{\circ}C$, and tin oxide films($SnO_2$) were prepared by thermal oxidation of the metallic tin films at $650^{\circ}C$ for 3 hours in oxygen ambient. The film analyses were carried out by SEM and XRD techniques. Effects of humidity and ambient temperature on the resistance of the sensing layer were found to be negligible. The fabricated micro-gas sensor exhibited high sensitivity to butane gas.

• Korean Journal of Optics and Photonics
• /
• v.8 no.6
• /
• pp.445-449
• /
• 1997

The complex refractive indices of $Ge_2Se_2Te_5$ which show reversible phase change between the crystalline phase and an amorphous one depending upon the annealing process have been determined in the spectral range of 0.7-4.5 eV. The $Ge_2Se_2Te_5$ films were DC sputter deposited on the crystalline silicon substrate. The spectro-ellipsometry data of a thick film were analyzed following the modelling procedure where the quantum mechanical dispersion relation were used for the complex refractive indices of both the cryastalline phase $Ge_2Se_2Te_5$ and and amorphous phase $Ge_2Se_2Te_5$, respectively. On the other hand, with the surface micro-roughness layer whose effective thickness was determined from AFM analysis, the spectro-ellipsometry data were numerically inverted to yield the complex refractive index of $Ge_2Se_2Te_5$ at each wavelength. With these set of complex refractive indices, the reflectance spectra were calculated and those spectra obtained from the numerical inversion showed better agreement with the experimental reflection spectra for both the cryastalline phase and an amorphous phase. Finally, the thin $Ge_2Se_2Te_5$ film which has the optimum thickness of 26 nm as the medium for optical recording was also analyzed and the quantitative result of the film thickness and the surface microroughness has been reported.

• Journal of Korean Ophthalmic Optics Society
• /
• v.14 no.1
• /
• pp.63-68
• /
• 2009

Purpose: TiN films were deposited on sus304 by unbalanced magnetron sputtering system which was designed and developed as unbalancing the strength of the magnets in the magnetron electrode. The effect of oxygen incorporation in the fabrication of deposited films was investigated. Methods: The cross sections of deposited films on Silicon wafer were observed by SEM to measure the thickness of the films, the components of the surface of the films were identified by XPS survey spectra, the compositional depth-profile of deposited films was examined by an XPS apparatus. Results: From the data of XPS depth profile of films, it could be seen that the element O as well as the elements Ti and N present in the surface of the film and the relative percentage of the element O was constant at 65 at.% with respect to the depth of film. Conclusions: The color change with thickness of the films had something to do with the change of Ti $ 2p_{3/2}$ peak intensity and shape mixed of $ TiO_2$, TiN, $ TiO_{x}N_{y}$ compound.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.6-15
• /
• 1997

This paper presents the multi-objective optimal design of thermopile sensor having beam or membrane structure. The thermopile sensor is composed of $Si_{3}N_{4}/SiO_{2}$ dielectric membrane, Al-polysilicon thermocouples and $RuO_{2}$ thin film for black body. The sensing method is based on the Seebeck effect which is originated from the temperature difference of the two positions, black body and silicon rim. The objective functions of the presented design are sensitivity, detectivity and thermal time constant. The modelling of the sensor is proposed including the package. The multi-objective optimization technique is applied to the design of the sensor not only inspecting the modelling equation but also simulating mathematical programming method. Especially, fuzzy optimization technique is adapted to get the optimal solution which enables the designer to reach the more practical solution. The design constraint of the voltage output originated from the change of the environmental temperature is included for practical use.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.63.1-63.1
• /
• 2010

실리콘 박막 태양전지의 효율을 향상시키기 위해 밴드갭이 다른 흡수층을 적용한 tandem형 적층 태양전지를 이용하고 있다. 일반적으로 1.7eV이상의 밴드갭이 큰 비정질 실리콘을 이용하여 단파장의 빛을 흡수하고, 상대적으로 낮은 1.1eV 정도의 밴드갭을 갖는 미세결정 실리콘 층으로 장파장을 흡수하게 된다. 이렇게 연결된 tandem형 태양전지의 효율을 극대화하기 위해서는 각 태양전지에서 발생하는 전류 밀도를 일치시키는 것이 필요하다. 이를 위해 비정질 실리콘의 두께가 증가되는 경우가 있는데 이러한 경우 비정질 실리콘의 광열화 특성(Lihgt-induced degradation)으로 안정화 효율이 감소하게 된다. 따라서 비정질 실리콘 태양전지의 전류 밀도를 향상 시켜 두께를 최소화하는 것이 매우 중요하다. Tandem형 태양전지에서 비정질 실리콘 태양전지의 전류 밀도를 향상시키기 위해 두 개의 전지사이에 광 반사층을 적용하여 태양전지를 제조하게 된다. 이러한 경우 비정질 실리콘의 전류 밀도는 증가하지만, 광 반사 층의 장파장 흡수로 인하여 하부 태양전지의 전류 밀도 감소가 더 커지게 되어 전체 발생 전류 밀도는 오히려 감소하게 된다. 본 논문에서는 비정질 실리콘의 밴드갭을 제어하여 광 흡수 파장 영역 확대로 전류 밀도를 향상시키는 연구를 진행하였다. PECVD의 RF power 조건을 제어하여 1.75eV에서 1.67eV까지 밴드갭을 변화시켰다. 이와 같은 조건의 박막을 광 흡수층으로 갖는 p-i-n 구조의 비정질 실리콘 태양전지를 제작하였다. i층의 밴드갭이 감소됨에 따라 장파장 영역의 흡수가 확대되어 전류 밀도가 증가 하였지만, Voc의 감소가 컸다. 이는 i층의 밴드갭이 좁아짐에 따라 p층과의 불연속성이 커졌기 때문이다. 이러한 악영향을 줄이기 위해 p층과 i층 사이에 buffer층을 삽입하여 태양전지를 제작하였다. 이와 같은 최적의 buffer층 삽입을 통하여 불연속성을 줄임으로써 Voc의 상승효과를 확인하였다. 본 연구의 결과로 좁은 밴드갭을 갖는 광 흡수 층을 적용하여 전류 밀도를 향상시키고, 최적화된 buffer층 삽입으로 Voc를 향상시킴으로써 고효율의 비정질 실리콘 태양전지를 제작하였다. 이를 tandem형 태양전지에 적용할 경우 초기 효율뿐만 아니라 얇은 두께에서 제조할 수 있기 때문에 광열화 특성이 향상되어 안정화 효율의 증가를 가져올 수 있다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.10
• /
• pp.34-41
• /
• 2010

We proposed the new pixel compensation circuit with high aperture ratio and the driving method for the large-area, low-power AMOLED applications in this study. We designed with the low-temperature poly-silicon(LTPS) thin film transistors(TFTs) that has poor uniformity but good mobility and stability. To lower the error rate of the pixel circuit and to improve the aperture ratio for bottom emission method, we simplified the pixel compensation circuit. Because the proposed pixel compensation circuit with high aperture ratio has very low contrast ratio for conventional driving methods, we proposed the new driving method and circuit for high contrast ratio. Black data insertion was introduced to improve the characteristics for moving images. The pixel circuit was designed for 19.6" WXGA bottom-emission AMOLED panel, and the average aperture ratio of the pixel circuit is improved from 33.0% to 41.9%. For the TFT's $V_{TH}$ variation of ${\pm}0.2\;V$, the non-uniformity and contrast ratio of the designed panel was estimated under 6% and over 100000:1 respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.11
• /
• pp.48-55
• /
• 2016

Ambient-light sensor system, which changes the brightness of a display as ambient light change, was studied to reduce the power consumption of the mobile applications such as note PC, tablet PC and smart phone. The ambient-light sensor system should be integrated on a display panel to improve the complexity and cost of mobile applications, so the ambient-light sensor and readout circuit was integrated on a display panel using low-temperature poly-silicon thin film transistors (LTPS-TFT). We proposed the new compensation method to correct the panel-to-panel variation of the ambient-light sensors, without additional equipment. We designed and investigated the new readout circuit with the proposed compensation method and the analog-to-digital converter for the final digital output of ambient light. The readout circuit has very simple structure and control timing to be integrated with LTPS-TFT, and the input luminance ranges from 10 to 10,000 lux. The readout rate is 100 Hz, and maximum differential non-uniformity with 20 levels of the final output below 0.5 LSB.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.210.1-210.1
• /
• 2015

최근 산화물 반도체에 대한 연구가 활발하게 이루어지고 있다. 비정질 산화물 반도체인 In-Ga-Zn-O (IGZO)는 기존의 비정질 실리콘에 비해 공정 단가가 낮으며 넓은 밴드 갭으로 인한 투명성을 가지고 있고, 저온 공정이 가능하여 다양한 기판에 적용이 가능하다. 반도체의 공정 과정에서 열처리는 소자의 특성 개선을 위해 필요하다. 일반적인 열처리 방법으로 furnace 열처리 방식이 주로 이용된다. 그러나 furnace 열처리는 시간이 오래 걸리며 일반적으로 고온에서 이루어지기 때문에 최근 연구되고 있는 유리나 플라스틱, 종이 기판을 이용한 소자의 경우 기판이 손상을 받는 단점이 있다. 이러한 단점들을 극복하기 위하여 저온 공정인 마이크로웨이브를 이용한 열처리 방식이 제안되었다. 마이크로웨이브 열처리 기술은 소자에 에너지를 직접적으로 전달하기 때문에 기존의 다른 열처리 방식들과 비교하여 에너지 전달 효율이 높다. 또한 짧은 공정 시간으로 공정 단가를 절감하고 대량생산이 가능한 장점을 가지고 있으며, 저온의 열처리로 기판의 손상이 없기 때문에 기판의 종류에 국한되지 않은 공정이 가능할 수 있을 것으로 기대된다. 따라서 본 연구에서는 마이크로웨이브 열처리가 소자의 전기적 특성 개선에 미치는 영향을 확인하였다. 제작된 IGZO 박막트렌지스터는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. RCA 클리닝을 진행한 후 RF sputter를 사용하여 In-Ga-Zn-O (1:1:1)을 70 nm 증착하였다. 이후에 Photo-lithography 공정을 통하여 active 영역을 형성하였고, 전기적 특성 평가가 용이한 junctionless 트랜지스터 구조로 제작하였다. 후속 열처리 방식으로 마이크로웨이브 열처리를 1000 W에서 2분간 실시하였다. 그리고 기존 열처리 방식과의 비교를 위해 furnace를 이용하여 N2 가스 분위기에서 $600^{\circ}C$의 온도로 30분 동안 열처리를 실시하였다. 그 결과, 마이크로웨이브 열처리를 한 소자의 경우 기존의 furnace 열처리 소자와 비교하여 우수한 전기적 특성을 나타내는 것을 확인하였다. 따라서, 마이크로웨이브를 이용한 열처리 공정은 향후 저온 공정을 요구하는 소자 공정에 활용될 수 있을 것으로 기대된다.

• Journal of the Korean Vacuum Society
• /
• v.14 no.2
• /
• pp.97-102
• /
• 2005

NO adsorption can be used in synthesizing oxynitride thin films which have potential application in nanodevices. However, it is very difficult to understand the oxynitridation Process since too many factors are involved in it. In this paper, we present our first-principles molecular dynamics calculation of the NO molecule adsorption on the Si(001) surface as the initial stage of the oxynitridation process. The previous first-principles calculation has argued the NO molecule is dissociated with a very small activation barrier, 0.07eV, which acutally corresponds to 1.60eV considering thermodynamics. This is in clear contrast to the observation that NO is dissociated at temperatures as low as 20K From extensive searches of NO on the Si(001) surface, we have found the new dissociation processes that have the much lower activation energies, less than 0.01 eV. We also present the dissociation and penetration processes with the corresponding activation energies and discuss their experimental implications.