• Korean Journal of Materials Research
• /
• v.14 no.2
• /
• pp.141-145
• /
• 2004

Silicon nitride thin films were deposited by atomic layer deposition (ALD) technique in a batch-type reactor by alternating exposures of precursors. XJAKO200414714156408$_4$ or$ SiH_2$$Cl_2$ was used as the Si precursor, $NH_3$ was used as the N precursor, and the deposited films were characterized comparatively. The thickness of the film linearly increased with the number of deposition cycles, so that the thickness of the film can be precisely controlled by adjusting the number of cycles. As compared with the deposition using$ SiCl_4$, the deposition using $SiH_2$$Cl_2$ exhibited larger deposition rate at lower precursor exposures, and the deposited films using $SiH_2$$Cl_2$ had lower wet etch rate in a diluted HF solution. Silicon nitride films with the Si:N ratio of approximately 1:1 were obtained using either Si precursors at $500^{\circ}C$, however, the films deposited using $SiH_2$$Cl_2$ exhibited higher concentration of H as compared with those of the $SiC_4$ case. Silicon nitride thin films deposited by ALD showed similar physical properties, such as composition or integrity, with the silicon nitride films deposited by low-pressure chemical vapor deposition, lowering deposition temperature by more than $200^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.134-138
• /
• 2000

The physical, electrical and piezoresitive characteristics of CrN(chromiun nitride) thin-films on silicon substrates have been investigated for use as strain gauges. The thin-film depositions have been carried out by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(5~25 %)$N_2$). The deposited CrN thin-films with thickness of $3500{\AA}$nd annealing conditions($300^{\circ}C$, 48 hr) in Ar-10 % $N_2$ deposition atmosphere have been selected as the ideal piezoresistive material for the strain gauges. Under optimum conditions, the CrN thin-films for the strain gauges is obtained a high electrical resistivity, $\rho=1147.65\;{\mu}{\Omega}cm$, a low temperature coefficient of resistance, TCR=-186 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal gauge factor, GF=11.17.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.11
• /
• pp.2095-2099
• /
• 2007

In this paper, the optimum amorphous silicon nitride thin film is deposited using plasma enhanced chemical vapor deposition(PECVD). Amorphous silicon nitride is deposited using $SiH_4$ and $NH_3$ gas. At this time, electrical and optical characteristics of amorphous silicon nitride and deposition rate are changed under deposition condition such as $SiH_4$, $NH_3$ and $N_2$ gas flow rate, chamber pressure, rf power and substrate temperature. From the experimental results, we can estimate that the deposition condition makes a good electrical characteristic of amorphous silicon nitride thin film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1175-1180
• /
• 2003

Transformer Coupled Plasma Chemical Vapor Deposited (TCP-CVD) silicon nitride (SiNx) is widely used as a gate dielectric material for thin film transistors (TFT). This paper reports the SiNx films, grown by TCP-CVD at the low temperature (30$0^{\circ}C$). Experimental investigations were carried out for the optimization o(SiNx film as a function of $N_2$/SiH$_4$ flow ratio varying ,3 to 50 keeping rf power of 200 W, This paper presents the dielectric studies of SiNx gate in terms of deposition rate, hydrogen content, etch rate and leakage current density characteristics lot the thin film transistor applications. And also, this work investigated means to decrease the leakage current of SiNx film by employing $N_2$ plasma treatment. The insulator layers were prepared by two step process; the $N_2$ plasma treatment and then PECVD SiNx deposition with SiH$_4$, $N_2$gases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.135-141
• /
• 2000

The physical, electrical and piezoresitive characteristics of CrN(chromiun nitride) thin-films on silicon substrates have been investigated for use as strain gauges. The thin-film depositions have been carried out by OC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(5~25 %)$N_2$). The deposited CrN thin-films with thickness of $3500{\AA}$ and annealing conditions($300^{\circ}C$, 48 hr) in Ar-10 % $N_2$ deposition atmosphere have been selected as the ideal piezoresistive material for the strain gauges. Under optimum conditions, the CrN thin-films for the strain gauges is obtained a high electrical resistivity, $\rho=1147.65\;{\mu}{\Omega}cm$, a low temperature coefficient of resistance, TCR=-186 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal gauge factor, GF=11.17.

• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.662-668
• /
• 1994

The physical and electrical characteristics of sub-l0nm thick capacitor dielectrics formed by wet oxidation of silicon nitride(oxide/nitride composite) and by removing the top oxide of oxidized silicon nitride(0xynitride) are described. For the capacitors with an oxide/nitride composite layer, the capacitance decreases sharply, but the breakdown field increases with an increase in the wet oxidation time at $900^{\circ}C$. For the capacitors with oxynitride layers, the values of both the capacitance and the breakdown field increase with increasing wet oxidation time. The reduction of effective thickness and the improved quality of oxynitride film are responsible for the improved capacitance and increased breakdown fields, respectively. In addition, intrinsic TDDB characteristics and early breakdown failure rate of oxynitride film are improved with increasing oxidation time. Consequently, the oxynitride film is suitable for dynamic memories as a thin dielectric film.

• Journal of the Korean Vacuum Society
• /
• v.12 no.4
• /
• pp.263-268
• /
• 2003

Precise thickness control and excellent properties of silicon nitride thin films are essential for the next-generation semiconductor and display devices. In this study, silicon nitride thin films were deposited by batch-type atomic layer deposition (ALD) method using $SiC1_4$ and $NH_3$ as the precursors at temperatures ranging from 500 to $600^{\circ}C$. Thin film deposition using a batch-type ALD reactor was a layer-by-layer atomic growth by self-limiting surface reactions, and the thickness of the deposited film can be controlled by the number of deposition cycles. The silicon nitride thin films deposited by ALD method exhibited composition, refractive index and wet etch rate similar with those of the thin films deposited by low-pressure chemical vapor deposition method at $760^{\circ}C$. The addition of pyridine mixed with precursors increased deposition rate by 50%, however, the films deposited with pyridine was readily oxidized owing to its unstable structure, which is unsuitable for the application to semiconductor or display devices.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.2
• /
• pp.17-21
• /
• 2004

Aluminum nitride(AlN) thin films were deposited on silicon substrate by reactive RF magnetron sputtering without substrate heating. We investigated the dependence of some properties for AlN thin film on sputtering conditions such as working pressure, $N_2$ concentration and RF power. XRD, Ellipsometer and AES has been measured to find out structural properties and preferred orientation of AlN thin films. Deposition rate of AlN thin film was increased with an increase of RF power and decreased with an increase of $N_2$ concentration. AES in-depth measurements showed that stoichiometry of Aluminium and Nitrogen elements were not affected by $N_2$ concentration. It has shown that low working pressure, low $N_2$ concentration and high RF power should be maintained to deposit AlN thin film with a high degree of (0002) preferred orientation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.109-111
• /
• 2007

Pulsed DC 마그네트론 스퍼터링 장치를 이용하여 Polymer 및 Glass 기판 위에 $SiN_{\chi}$ (Silicon Nitride) 박막을 합성 시키고 이들의 구조적, 광학적 특성을 조사하였다. 막두께는 100 nm로 고정하였으며, power mode 및 질소 가스 유량비를 변수로 합성하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.220-223
• /
• 1996

Mechanical properties of Plasma-Enhanced Chemical Vapor Deposited (PECVD) silicon nitride thin film was studied to determine the feasibility of the film as a passivation layer over the aluminum bonding areas of integrated circuit chips. Ultimate strain of the films in thicknesses of about 5 k${\AA}$ was measured using four-point bending method. The ultimate strain of these films was constant at about 0.2% regardless of residual stress. Intrinsic and residual stresses of these films were measured and compared with thermal shock and cycling test results. Comparison of the results showed that more tensile films were more susceptible to crack- induced failure.