• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.128.1-128.1
• /
• 2011

In amorphous silicon and crystalline silicon(a-Si:H/c-Si) heterojuction solar cells, intrinsic hydrogenated amorphous silicon(a-Si:H) films play an important role to passivate the crystalline silicon wafer surfaces. We have studied the correlation between the surface passivation quality and nature of the Si-H bonding at the a-Si:H/c-Si interface. The samples were obtained by VHF-CVD under different deposition conditions. The passivation quality and analysis of all structures studied was performed by means of quasi steady state photoconductance(QSSPC) methods and fourier transform infrared spectrometer(FTIR) measurements respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.229-229
• /
• 2007

• Korean Journal of Materials Research
• /
• v.21 no.9
• /
• pp.491-496
• /
• 2011

Transparent conducting oxides (TCOs) used in the antireflection layer and current spreading layer of heterojunction solar cells should have excellent optical and electrical properties. Furthermore, TCOs need a high work function over 5.2 eV to prevent the effect of emitter band-bending caused by the difference in work function between emitter and TCOs. Sn-doped $In_2O_3$ (ITO) film is a highly promising material as a TCO due to its excellent optical and electrical properties. However, ITO films have a low work function of about 4.8 eV. This low work function of ITO films leads to deterioration of the conversion efficiency of solar cells. In this work, ITO films with various Zn contents of 0, 6.9, 12.7, 28.8, and 36.6 at.% were fabricated by a co-sputtering method using ITO and AZO targets at room temperature. The optical and electrical properties of Zn-doped ITO thin films were analyzed. Then, silicon heterojunction solar cells with these films were fabricated. The 12.7 at% Zn-doped ITO films show the highest hall mobility of 35.71 $cm^2$/Vsec. With increasing Zn content over 12.7, the hall mobility decreases. Although a small addition of Zn content increased the work function, further addition of Zn content over 12.7 at.% led to decreasing electrical properties because of the decrease in the carrier concentration and hall mobility. Silicon heterojunction solar cells with 12.7 at% Zn-doped ITO thin films showed the highest conversion efficiency of 15.8%.

• Korean Journal of Materials Research
• /
• v.21 no.2
• /
• pp.120-124
• /
• 2011

Silicon heterojunction solar cells have been studied by many research groups. In this work, silicon heterojunction solar cells having a simple structure of Ag/ZnO:Al/n type a-Si:H/p type c-Si/Al were fabricated. Samples were fabricated to investigate the effect of transparent conductive oxide growth conditions on the interface between ZnO:Al layer and a-Si:H layer. One sample was deposited by ZnO:Al at low working pressure. The other sample was deposited by ZnO:Al at alternating high working pressure and low working pressure. Electrical properties and chemical properties were investigated by light I-V characteristics and AES method, respectively. The light I-V characteristics showed better efficiency on sample deposited by ZnO:Al by alternating high working pressure and low working pressure. Atomic concentrations and relative oxidation states of Si, O, and Zn were analyzed by AES method. For poor efficiency samples, Si was diffused into ZnO:Al layer and O was diffused at the interface of ZnO:Al and Si. Differentiated O KLL spectra, Zn LMM spectra, and Si KLL spectra were used for interface reaction and oxidation state. According to AES spectra, sample deposited by high working pressure was effective at reducing the interface reaction and the Si diffusion. Consequently, the efficiency was improved by suppressing the SiOx formation at the interface.

• Current Photovoltaic Research
• /
• v.9 no.4
• /
• pp.111-122
• /
• 2021

Silicon heterojunction technology (HJT) solar cells have received considerable attention due to advantages that include high efficiency over 26%, good performance in the real world environment, and easy application to bifacial power generation using symmetric device structure. Furthermore, ultra-highly efficient perovskite/c-Si tandem devices using the HJT bottom cells have been reported. In this paper, we discuss the unique feature of the HJT solar cells, the fabrication processes and the current status of technology development. We also investigate practical challenges and key technologies of the HJT solar cell manufacturers for reducing fabrication cost and increasing productivity.

• Solar Energy
• /
• v.8 no.1
• /
• pp.41-48
• /
• 1988

Heterojunction solar cells of $n-Cd_{1-x}Zn_xS/p-Si$ were fabricated by solution growth technique. The crystal structure, spectral response, surface morphology, and I-V characteristics of the $n-Cd_{1-x}Zn_xS/p-Si$ heterojunction solar cells were studied. The $Cd_{1-x}Zn_xS$ layer deposited on a silicon substrate (111) were found to be a cubic structure with the crystal orientation (111), (220) of the CdS and to be a hexagonal structure with crystal orientation (100) of the ZnS. The open-circuit voltage, short-circuit current, fill factor, and conversion efficiency of $n-Cd_{1-x}Zn_xS/p-Si$ heterojunction solar cell under $100mW/cm^2$ illumination were found to be 0.43V, 38mA. 0.76, and 12.4%, respectively.

• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.341-346
• /
• 2011

In this study, we inserted a Zn buffer layer into a AZO/p-type a-si:H layer interface in order to lower the contact resistance of the interface. For the Zn layer, the deposition was conducted at 5 nm, 7 nm and 10 nm using the rf-magnetron sputtering method. The results were compared to that of the AZO film to discuss the possibility of the Zn layer being used as a transparent conductive oxide thin film for application in the silicon heterojunction solar cell. We used the rf-magnetron sputtering method to fabricate Al 2 wt.% of Al-doped ZnO (AZO) film as a transparent conductive oxide (TCO). We analyzed the electro-optical properties of the ZnO as well as the interface properties of the AZO/p-type a-Si:H layer. After inserting a buffer layer into the AZO/p-type a-Si:H layers to enhance the interface properties, we measured the contact resistance of the layers using a CTLM (circular transmission line model) pattern, the depth profile of the layers using AES (auger electron spectroscopy), and the changes in the properties of the AZO thin film through heat treatment. We investigated the effects of the interface properties of the AZO/p-type a-Si:H layer on the characteristics of silicon heterojunction solar cells and the way to improve the interface properties. When depositing AZO thin film on a-Si layer, oxygen atoms are diffused from the AZO thin film towards the a-Si layer. Thus, the characteristics of the solar cells deteriorate due to the created oxide film. While a diffusion of Zn occurs toward the a-Si in the case of AZO used as TCO, the diffusion of In occurs toward a-Si in the case of ITO used as TCO.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.287.2-287.2
• /
• 2016

Silicon has considerably good characteristics on electron, hole mobility and its price. With 2-D sinlge-layer Graphene/n-Si heterojunction solar cell shows that in one sun condition exhibit power conversion efficiency(PCE) of 10.1%. This photovoltaic effect was achieved by applying gate voltage to the Schottky junction of the heterostructure solar cell. Energy band diagram shows that Schottky barrier between Si and graphene can be adjust by the external electric field. because of the fermi level of the graphene can be changed by external gate voltage, we can control the Schottkky barrier of the heterostructure solar cell. The ratio between generated power of solar cell and consumption electrical power is remarkable. Since we use the graphene as the top gate electrode, most of the sun light can penetrate into the active area.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.346-346
• /
• 2009

For high efficiency hetero junction solar cell over 20%, good silicon wafer passivation is one of the most important technological factor. Compared to the conventional PECVD technique, HWCVD has appeared as an promising alternative for high quality passivation layer formation. In this work, HWCVD passivation layer characteristics have been intensively investigated on wafer surface treatment, Hydrogen density in deposited thin layer and thermal effects in deposition process. Comprehensive results of the individual process factors on interface passivation has been discussed and resultant silicon hetero junction solar cell characteristics has been investigated.

• Current Photovoltaic Research
• /
• v.3 no.4
• /
• pp.107-111
• /
• 2015

Current characteristic curve of an illuminated solar cell was used to determine its reverse saturation current density ($J_0$), ideality factor (n) and resistances, by using numerical diode simulation. High efficiency amorphous silicon, heterojunction crystalline Si (HIT), plastic and organic-inorganic halide perovskite solar cell shows n=3.27 for a-Si and n=2.14 for improved HIT cell as high and low n respectively, while the perovskite and plastic cells show n=2.56 and 2.57 respectively. The $J_0$ of these cells remain within $7.1{\times}10^{-7}$ and $1.79{\times}10^{-8}A/cm^2$ for poorer HIT and improved perovskite solar cell respectively.