• Applied Chemistry for Engineering
• /
• 제20권1호
• /
• pp.80-86
• /
• 2009

In this study, binderless zeolite BaX granule, an effective adsorbent for the separation of p-xylene was made. This adsorbent which has a sufficient strength, high specific surface area and selectivity to p-xylene was prepared by various steps, such as granulation process, calcination, binderless treatment, ion-exchange, and activation. In the granulation, the concentration of colloidal silica solution was controlled in order to confirm the effect of $SiO_2$ contents after binderless treatment. As a result, we confirmed that the compressive strength of granule after binderless treatment was increasing with increasing proportion of $SiO_2$ in the granule. And then Na-ion in granule was exchanged with Ba-ion by successive batch ion-exchange process. And then prepared adsorbents were tested for p-xylene separation by batch adsorption at $90^{\circ}C$. As a results of batch adsortion test, we confirmed that prepared adsorbents have a high selectivity to p-xylene. Also, it could be conformed that the prepared binderless zeolite BaX has a sufficient compressive strength (0.450 kgf), high specific surface area $(647.57m^2/g)$, high crystallinity (98.5% compared with zeolite NaX powder), and selectivity to p-xylene.

• Polymer(Korea)
• /
• 제29권2호
• /
• pp.156-160
• /
• 2005

$\alpha,\omega-Vinyl$ poly (dimethyl-methylphenyl) siloxane prepolymer (VPMPS ) was prepared by the equilibrium polymerization of octamethylcyclotetrasiloxane $(D_4)$, 1,3,5-trimethyl-1,3,5-triphenylcyclotrisiloxane $(D_3^{Me,Ph)$, and 1,1,3,3-tetramethyl-1,3-divinyldisiloxane (MVS). And also, of $\alpha,\omega-hydrogen$ poly(dimethyl-methyl)siloxane prepolymer (HPDMS) as end blocker was prepared from octamethylcyclotetrasiloxane $(D_4)$, 1,3,5-trimethylcyclotrisiloxane $(D_3^:Me,H})$, and 1,1,3,3-tetramethyldisiloxane (MS). Nickel ferrite nanoparticles having spinel magnetic material was prepared by the sol-gel method using PAA as a chelating agent. Poly(organosiloxane) rubber nanocomposite containing silica and nickel ferrite ultrafine powder modified with 1,3-divinyltetramethyldisilazane (VMS) was prepared by compounding VPMPS, HPDMS, and catalyst in high speed dissolver. The mechanical properties, heat dissipating away characteristics, and volume resistivities for POX-30 and POX-50 were measured.

• Journal of Korean Ophthalmic Optics Society
• /
• 제3권1호
• /
• pp.217-222
• /
• 1998

Coating films of $SiO_2-TiO_2-AgO$ have been prepared on soda-lime-silica slide glasses and single crystal silicon wafer by the sol-gel method using a spin-coating technique. Commercially available tetraethyl orthosilicate, titanium trichloride, and silver-nitrates were used as starting materials. The heat treatment temperature of this coating films was $500^{\circ}C$ properly, obtained from TG-DTA result. The films with thickness of 310 nm were prepared by 5 times coating. In the case of l0 mol% AgO, the film showed a crack-free and smooth surface, but the higher Ago content exhibited the more pin hole and the segregated cluster of AgO. The IR absorbance of the films decreased in the range of 400 nm to 700 nm with the increase of annealing temperature. And the reflectance of the coating films decreased and the color was changed light yellow to white yellow with the increase of Ago content.

• Journal of Powder Materials
• /
• 제21권5호
• /
• pp.377-381
• /
• 2014

This work describes the coloration, chemical stability of $SiO_2$ and $SnO_2$-coated blue $CoAl_2O_4$ pigment. The $CoAl_2O_4$, raw materials, were synthesized by a co-precipitation method and coated with silica ($SiO_2$) and tin oxide ($SnO_2$) using sol-gel method, respectively. To study phase and coloration of $CoAl_2O_4$, we prepared nano sized $CoAl_2O_4$ pigments which were coated $SiO_2$ and $SnO_2$ using tetraethylorthosilicate, $Na_2SiO_3$ and $Na_2SiO_3$ as a coating material. To determine the stability of the coated samples and their colloidal solutions under acidic and basic conditions, colloidal nanoparticle solutions with various pH values were prepared and monitored over time. Blue $CoAl_2O_4$ solutions were tuned yellow color under all acidic/basic conditions. On the other hand, the chemical stability of $SiO_2$ and $SnO_2$-coated $CoAl_2O_4$ solution were improved when all samples pH values, respectively. Phase stability under acidic/basic condition of the core-shell type $CoAl_2O_4$ powders were characterized by transmission electron microscope, X-ray diffraction, CIE $L^*a^*b^*$ color parameter measurements.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.306-308
• /
• 2007

Poly(ethylene glycol) dimethyl ether (PEGDME)/fumed silica/ 1-methyl -3-propylimidazolium iodide (MPII)/$I_2$ mixtures were used as polymer electrolytes in solid state dye-sensitized solar cells (DSSCs). The contents of MPII were changed and the concentration of $I_2$ was fixed at 0.1 mole% with respect to the MPII. The maximum ionic conductivity was obtained at [EG]:[MPII]:[$I_2$]=10:1.5:0.15. It was supposed that the maximum of ionic conductivities would match with that of cell efficiencies, if the ionic conductivity is a rate determining step in the sol id state DSSCs. However, the maximum composition did not show the maximum solar cell performance, indicating the mismatch between ionic conductivity and cell performance. This suggests that the ionic conductivity may not be the rate controlling step in determining the cell efficiency in these experimental conditions, whereas other parameters such as the electron recombination might play an important role. Thus, we tried to modify the surface of the $TiO_2$ particles by coating a thin metal oxide such as $Al_2O_3$ or $Nb_2O_5$ layer to prevent electron recombination. As a result, the maximum of the cell efficiency was shifted to that of the ionic conductivity. The peak shifts were also attempted to be explained by the diffusion coefficient and the lifetime of electrons in the $TiO_2$ layer.

• Journal of the Korean GEO-environmental Society
• /
• 제14권1호
• /
• pp.53-60
• /
• 2013

On this study, engineering properties of SGR method and SMI method, which are typical sodium silicate methods, were compared through the laboratory test and durability, strength, waterproof characteristic and environmental effects were compared and analyzed with period and condition of curing on each case. As a result of durability test, volume change of SGR is approximately 23-times greater than SMI and the effects on environment are appeared safe on all method. In case of waterproof characteristic test, permeability coefficient is decreased about 24% on SMI, whereas on SGR permeability coefficient is showed to increase because rapid volume change make wider void. Strength characteristics of SMI are appeared higher about 11-times in case of homogel and 3.9-times in case of sandgel than SGR. Which is because volume change of SMI, caused by leaching, is smaller than SGR.

• Journal of the Korean Chemical Society
• /
• 제47권6호
• /
• pp.619-624
• /
• 2003

The $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ (x=0.02, 0.05, 0.08, and 0.12) powders (${\thickapprox}1{\mu}m$) synthesized by sol-gel method, whose surfaces are modified in a colloidal silica suspension (size of $SiO_2$ particles: ${\sim}30$ nm), have been fabricated to highly stable and effective luminescent films on the glass substrates. Thanks to the fused $SiO_2$ nano particles in the vicinity of the glass softening temperature (at around $700^{\circ}C$), $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ powders are strongly attached onto the surface of glass substrate (>9H, pencil hardness tester). This simple and low-cost method to get $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ phosphor films without any loss of luminescence brightness would promise for applications to display devices.

• Corrosion Science and Technology
• /
• 제14권5호
• /
• pp.213-217
• /
• 2015

Recently, household electronic industries require environmentally-friendly and highly functional steels in order to enhance the quality of human life. Customers especially require both excellent corrosion and abrasion resistant anti-fingerprint steels for digital TV panels. Thus POSCO has developed new functional electro-galvanized steels, which have double coated layers with organic-inorganic composites on the zinc surface of the steel for usage as the bottom chassis panel of TVs. The inorganic solution for the bottom layer consists of inorganic phosphate, magnesium, and zirconium compounds with a small amount of epoxy binder, and affords both improved adhesion properties by chemical conversion reactions and corrosion resistance due to a self-healing effect. The composite solution for the top layer was prepared by fine dispersion of organic-inorganic ingredients that consist of a urethane modified polyacrylate polymer, hardener, silica sol and a titanium complex inhibitor in aqueous media. Both composite solutions were coated on the steel surface by using a roll coater and then cured through an induction furnace in the electro-galvanizing line. New anti-fingerprint steel was evaluated for quality performance through such procedures as the salt spray test for corrosion resistance, tribological test for abrasion resistance, and conductivity test for surface electric conductance regarding to both types of polymer resin and coating weight of composite solution. New composite coated anti-fingerprint steels afford both better corrosion resistance and abrasion properties compared to conventional anti-fingerprint steel that mainly consists of acrylate polymers. Detailed discussions of both composite solutions and experimental results suggest that urethane modifications of acrylate polymers of composite solutions play a key role in enhanced quality performances.

• Korean Journal of Materials Research
• /
• 제23권1호
• /
• pp.53-58
• /
• 2013

Superhydrophobic $SiO_2$ layers with a micro-nano hierarchical surface structure were prepared. $SiO_2$ layers deposited via an electrospray method combined with a sol-gel chemical route were rough on the microscale. Au particles were decorated on the surface of the microscale-rough $SiO_2$ layers by use of the photo-reduction process with different intensities ($0.11-1.9mW/cm^2$) and illumination times (60-240 sec) of ultraviolet light. With the aid of nanoscale Au nanoparticles, this consequently resulted in a micro-nano hierarchical surface structure. Subsequent fluorination treatment with a solution containing trichloro(1H,2H,2H,2H-perfluorooctyl)silane fluorinated the hierarchical $SiO_2$ layers. The change in surface roughness factor was in good agreement with that observed for the water contact angle, where the surface roughness factor developed as a measure needed to evaluate the degree of surface roughness. The resulting $SiO_2$ layers revealed excellent repellency toward various liquid droplets with different surface tensions ranging from 46 to 72.3 mN/m. Especially, the micro-nano hierarchical surface created at an illumination intensity of $0.11mW/cm^2$ and illumination time of 60 sec showed the largest water contact angle of $170^{\circ}$. Based on the Cassie-Baxter and Young-Dupre equations, the surface fraction and work of adhesion for the micronano hierarchical $SiO_2$ layers were evaluated. The work of adhesion was estimated to be less than $3{\times}10^{-3}N/m$ for all the liquid droplets. This exceptionally small work of adhesion is likely to be responsible for the strong repellency of the liquids to the micro-nano hierarchical $SiO_2$ layers.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 한국결정성장학회 1996년도 제11차 KACG 학술발표회 Crystalline Particle Symposium (CPS)
• /
• pp.29-53
• /
• 1996

다공성 실리카 게 분말은 저밀도, 고비표면적의 특성을 가지며 물리적, 화학적 성질이 우수하여 필름의 점착방지제, 페인트의 소광제, 맥주의 흡착제, 촉매의 담지체등 산업전반에 걸쳐 여러용도로 사용되고 있다. 이러한 다공성 실리카 겔 분말은 고상법, 기상법, 액상법등으로 제조할 수 있으며, 이 중에서 sodium silicate를 원료로 하는 액상공정은 다공성의 제어가 용이하고, 공정이 간단하며, 고순도의 균질한 실리카를 얻을 수 있는 방법으로 많이 사용되고 있다. 본 연구에서는 액상법(sol-gel method)를 사용하여 점착방지제, 소광제 등으로 사용되는 다공성 실리카 겔 미분말의 개발에 초점을 두어 연구하였다. 그리고, 겔 분말의 다공성 제어를 위하여 공정 각 단계에서의 겔 내부의 구조의 변화에 대한 연구와 함께 수화겔의 숙성이 기공특성에 미치는 영향, 건조조건의 기공특성에 대한 영향 등을 살펴보았다. 다공성 실리카 겔 미분말은 다음과 같은 공정에 의해 제조되었다. sodium silicate를 황산과 반응시켜 겔화하고 추가의 황산을 투입하여 미반응분의 Na를 제거한 후 pH 7이상의 알카리 영역에서 숙성하여 다공성을 지닌 실리카 수화겔을 제조하였다. 수화겔의 탈수, 세척, 건조 공정을 거쳐 건조겔을 제조하고, 1-20$\mu\textrm{m}$의 크기로 분쇄하여 최종 제품을 얻을 수 있었다. 최종 다공성 실리카 겔 분말은 비표면적 200-700$m^2$/g, 기공부피 0.5-2.5cc/g, 평균 입경 3-5$\mu\textrm{m}$, 백색도 95% 이상의 물성을 보였다. sodium silicate와 황산의 겔화 반응에 의해 생성된 수화겔은 수 nm크기의 일차입자들의 연속적인 network로이루어져 있으며, 일차입자크기가 너무 작기 때문에 내부의 기공들은 별로 존재하지 않는 상태이다. 2차 주가황산 투입에 의해 미반응의 알카리 이온들을 중화, 제거시킬 수 있으며, 겔의 다공성을 좌우하는 숙성단계에서 숙성 pH, 온도, 시간등의 인자에 의해 수화겔의 기공특성을 제어할 수 있다. pH 7이상에서 실리카의 용해도가 크고, 용해도의 입자크기 의존성이 크므로, 일자입자는 Ostwald-ripening에 의해 계속 성장할 수 있으며, 이때, 입자의 성장은 숙성 온도와 시간에 의존한다. 탈수, 세척공정에 의해 가용성 염인 Na2SO4를 제거하고, 건조조건을 변화시킴으로써 기공부피를 증가시키는 것이 가능하였으며, Fast drying을 사용하여 점착방지제에 적합한 기공부피를 갖는 실리카 건조겔을 제조할 수 있었다.