• Journal of the Korean Ceramic Society
• /
• v.31 no.12
• /
• pp.1475-1482
• /
• 1994

Compositionally triphasic boehmite-silica-zirconia composite gels were prepared by a multiphasic sol-gel route. Phase-formation characteristics and densification behavior of the gel compacts were examined with and without $\alpha$-Al2O3 seeding. In the unseeded triphasic gels, both $\alpha$-Al2O3 and mullite crystallize simultaneously at 130$0^{\circ}C$. On the other hand, the $\alpha$-Al2O3 seeding selectively induces the formation of corundum phase ($\alpha$-Al2O3) at a significantly lower temperature (~110$0^{\circ}C$) and facilitates an epitaxial growth of $\alpha$-Al2O3 between 1100~130$0^{\circ}C$. The densification of alumina-mullite-zirconia composite (derived from the triphasic gels) was also enhanced by the $\alpha$-Al2O3 seeding, and this was attributed to the delayed crystallization of mullite in the $\alpha$-Al2O3 seeded gel.

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.394-400
• /
• 1990

Mullite and cordierite were prepared by the sol-gel route. Boehmite, fumed silica and Mg(NO3)2$.$6H2O were their starting materials. Mullite and cordierite powder were mixed by various weight percent. These mixed sols were ball-milled for 48hrs, dried at 100$^{\circ}C$, pressed, cold isostatic pressed and sintered at 1490$^{\circ}C$ for 2hrs. Mullite-cordierite composites sintered at 1490$^{\circ}C$ for 2hrs had>98% of theoretical density. Bending strength of the sintered bodies were 329-249MPa, dielectric constant 7.1-6.7 at 1MHz and thermal expansion coefficient at 800$^{\circ}C$ was matched with Si in the range of 30-35wt% cordierite.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.10a
• /
• pp.151-152
• /
• 2008

PCM has the ability to change their state, these materials absorb energy during the heating process as a body contact and release energy during a reverse cooling process as phase change take place. Using the thermal energy storage of PCM which has a melting point 15 to $35^{circ}C$ is one of the most effective ideas for utilization in textile finish. In this study, microencapsulated PCM(MCPCM) were synthesized by sol-gel method using the octadecane(or nonadecane) as PCM and the silica as microcapsule materials. To develop smart temperature adaptable textile, coating process was applied to textile substrate using a composition included MCPCM.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2008.05a
• /
• pp.164-164
• /
• 2008

• Environmental Engineering Research
• /
• v.7 no.4
• /
• pp.227-237
• /
• 2002

Chemical vapor deposition (CVD), ion beam sputtering (IBS) and sol-gel method were used to prepare TiO$_2$ thin films for degradation of hazardous organic compounds exemplified by 2-chlorophenol (2-CP). The influence of supporting materials and coating methods on the photocatalytic activity of the TiO$_2$ thin films were also studied. TiO$_2$ thin films were coated onto various supporting materials including steel cloth (SS), copper cloth, quartz glass tube (QGT), and silica gel (SG). Results indicate that SS (37 μm)- TiO$_2$ thin film prepared by IBS method improves the photodegradation of 2-CP. Among all supporting materials studied, SS(37 μm) is found to be the best support.

• Journal of the Korean Ceramic Society
• /
• v.34 no.7
• /
• pp.747-757
• /
• 1997

ZSM-5 zeolite composite membranes have been synthesized from a silica sol solution containing TPABr as an organic template by the dip-coating and the pressurized-coating hydrothermal treatment techniques. The CO2 separation efficiency of synthesized composite membranes was also investigated. The permeation mechanism of CO2 through ZSM-5 membranses was the surface diffusion, and that of N2, O2, and He gases was Knudsen diffusion or activated diffusion depending on the synthetic method of membranes and the measurement temperature. The CO2/N2 separation factor of the membrane prepared by the dip-coating hydrothermal treatment was 2.5 at about 12$0^{\circ}C$, while the ZSM-5 composite membrane synthesized by the pressurized-coating hydrothermal treatment technique showed the CO2/N2 separation factor of 9.0 at room temperature higher than that ever reported in the literature.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.549-554
• /
• 2006

In this paper we first applied the chemical mechanical polishing (CMP) process to the planarization of ferroelectric film in order to obtain a good planarity between electrode and ferroelectric film. $Pb_{1.1}(Zr_{0.52}Ti_{0.48})O_3$ (shortly PZT) ferroelectric film was fabricated by the sol-gel method. And then, we compared the structural characteristics before and after CMP process of PZT films. Removal rate, WIWNU% and surface roughness have been found to depend on slurry abrasive types and their hardness, especially, surface roughness and planarity were strongly depends on its pH value. A maximum in the removal rate is observed in the silica slurry, in contrast with the minimum removal rate occurs at ceria slurry. We found that the surface roughness of PZT films can be significantly reduced using the CMP technique.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.77-81
• /
• 2000

Silica glass films to utilize optical waveguides was fabricated by Aerosol Flame Deposition(AFD) method. As the amount of B2O3 increased in the sol solution of (92-x)SiO2-xB2O3-8P2O5, the thermophoretic deposition rate onto Si substrate was markedly lowered due to vaporizing out of B2O3 and P2O5 during the vaporization and reaction of the aerosol in the flame. GeO2 was added to 62SiO2-30B2O3-8P2O5 in order to control easily the refractive index of glass films. As the amount of GeO2 increased from 2 to 12 wt%, its refractive index increased from 1.4633 up to 1.4716.

• Proceedings of the KAIS Fall Conference
• /
• 2006.11a
• /
• pp.272-275
• /
• 2006

본 논문에서는 CMP(Chemical Mechanical Polishing) 슬러리용으로 사용되는 저가이면서 입도 분포가 균일한 콜로이달 실리카(Colloidal Silica)를 사용하여 추가의 첨가제 없이 열처리 공정만을 거쳐 석영유리를 제조하여 6N의 순도와 1 mm 두께 기준 86%의 자외선 투과율 그리고 AFM(Atomic Force Microscopy) 및 간섭계 현미경을 이용하여 표면의 거칠기가 1 nm 미만인 고순도 석영유리를 제조하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.71-72
• /
• 2011

최근 스마트 휴대폰으로 대표되는 이동통신기기 산업의 빠른 성장으로 인하여 이들 기기를 보호하기 위한 표면 처리기술이 함께 발전하고 있다. 그중 대표적인 것이 나노기술을 융합한 보호막 도장 기술이다. 본 연구에서는 마그네슘 기판과 플라스틱 케이스 소재 위에 유무기 하이브리드 도장막을 형성시키고, 도장막의 실리카 조성에 따른 물리화학적 변화 거동을 관찰하였다. 특히, 실리카 나노입자가 첨가된 실리카 졸 용액과 UV 경화수지를 다른 비율로 혼합한 나노형 하이브리드 코팅용액을 사용하였으며, 딥 코팅과 스프레이 코팅법을 개별적으로 이용하여 형성한 유무기 하이브리드 코팅층의 경도와 내지문 특성을 중점적으로 조사하였다. 이러한 연구를 통하여 유무기 하이브리드 코팅층 형성에서 실리카 졸의 역할과 최적 물성확보를 위한 근거를 마련하였다.