• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.367-371
• /
• 2006

Thermal properties of copolyetherester/silica nanocomposites were examined by using DSC and TGA. The segmented block copolyetheresters with various hard segment structures and hard segment contents (HSC) were synthesized and their silica nanocomposite films were prepared by solution casting method. The nano-sized fumed silica particles were found to act as a nucleating agent of the copolyetheresters. The nanocomposites always showed reduced degree of supercooling or faster crystallization than the corresponding copolyetheresters. The nanocomposites also showed increased hard segment crystallinity except HSC 35 sample which had short hard segment length. In case of 2GT [poly(ethylene terephthalate)] copolyetheresters, which were not developed commercially because of their low crystallization rate, the hard segment crystallinity increased considerably. The copolyetherester/silica nanocomposites showed better thermal stability than copolyetheresters.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.04a
• /
• pp.243-245
• /
• 2002

Brackish water desalination using reverse osmosis(RO) membrane is more useful and economic than sea water to solve the shortage of fresh water supply because of its low total dissolved solid(TDS) contents. Silica and humic acid in brackish water make serious fouling problems and cause the decline of permeate flux and increase of operating pressure. In this study, the experiments for removal of silica and humic acid were conducted with calcite particles to prevent membrane fouling and investigated the effect of pH of feed water Adsorption of silica to calcite was higher at pH=7.5 than 9.5 and removal rate was increased according to increase of initial concentration of silica. The effect of pH on adsorption of humic acid was not significant but at low initial concentration the adsorption of humic acid was enhanced at pH 7.5. The result of this study expect to apply to brackish water desalination experiment of flat-sheet reverse osmosis membrane.

• Elastomers and Composites
• /
• v.32 no.1
• /
• pp.11-19
• /
• 1997

[ ${\gamm}-Glycidoxy$ ] propyl trimethoxy silane, CTBN rubber(carboxyl terminated butadiene acrylonitrile rubber) and GMA(glycidyl methacrylate) were reacted on the surface of silica one by one in existence of TEA(triethylamine) or BPO(benzoyl peroxide). The amount of reactant was $2.5{\sim}5.8%$ of treated silica weight. The treated silica was mixed with epoxy resin and MTHPA(methyl tetrahydro phthalic anhydride) in the range of $0{\sim}60%$(wt.%) of total component. The thermal properties were tested for cured products. By using silica treated with silane/rubber or silane/rubber/vinyl, comparing with 3% of rubber mixed directly, it had 13% higher $T_g$ and 10% lower thermal expansion coefficient at $35{\sim}55%$ of silica contents.

• Structural Engineering and Mechanics
• /
• v.51 no.3
• /
• pp.403-412
• /
• 2014

In this paper, enhancement of corrosion and chloride resistance of high performance self compacting concrete (SCC) through incorporating nanosilica into the binder has been investigated. For this purpose, different mixtures were designed with different amounts of silica fume and nano silica admixtures. Different binder contents were also investigated to observe the binder content effect on the concrete properties. Corrosion behavior was evaluated by chloride penetration and resitivity tests. Water absorption and capillary absorption were also measured as other durability-related properties. The results showed that water absorption, capillary absorption and Cl ion percentage decreased rather significantly in the mixtures containing admixtures especially blend of silica fume and nano silica. By addition of the admixtures, resistivity of the SCC mixtures increased which can lead to reduction of corrosion probability.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.30-34
• /
• 2012

For the purpose of development of polymeric material for marine applications, the effects of silica and chopped glass fiber on tensile strength of polyester resin were studied. A series of experiments were performed with different contents of silica and chopped glass fiber. Tensile strength of polyester resin was increased with the contents of unmodified glass fiber, and decreased with that of silica. The surfaces of silica and chopped glass fiber were modified with coupling agent at different concentrations, and the modification showed positive effect on the increase of tensile strength of polyester resin. Synergistic effect on the tensile strength of polyester resin was observed by modified silica and chopped glass fiber.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.4
• /
• pp.125-133
• /
• 1998

In this study, an experiment in the field was performed to analyze the influence of steel fiber and silica fume on the rebound ratios of shotcrete. The experimental parameters which are the reinforcing methods(steel fiber, wire mesh), steel fiber contents(0.0%, 0.5%. 0.75%, 1.0%), silica fume contents(0.0%, 10.0%), and the three placing parts(side wall, shoulder, crown) were chosun. According to the results for the side wall in this test, the larger the fiber contents are in case of steel fiber reinforced shotcrete, the less the rebound ratios are within the range of 20~35%, compared to the wire mesh reinforced shotcrte. And also, the reduced rebound ratios were vary larger in using steel fiber reinforced shotcrete with silica fume content of 10%, and these results are true of the shoulder and the crown, respectively. In addition, the four-stage phenomenon for the rebound of the SFRS were estimated in the view of the co-action between steel fiber and coarse aggregate based upon the existing two-stage analysis method.

• Korean Journal of Materials Research
• /
• v.16 no.12
• /
• pp.731-738
• /
• 2006

It is seriously considered using Al CMP (chemical mechanical planarization) process for the next generation 45 nm Al wiring process. Al CMP is known that it has a possibility of reducing process time and steps comparing with conventional RIE (reactive ion etching) method. Also, it is more cost effective than Cu CMP and better electrical conductivity than W via process. In this study, we investigated 4 different kinds of slurries based on abrasives for reducing scratches which contributed to make defects in Al CMP. The abrasives used in this experiment were alumina, fumed silica, alkaline colloidal silica, and acidic colloidal silica. Al CMP process was conducted as functions of abrasive contents, $H_3PO_4$ contents and pressures to find out the optimized parameters and conditions. Al removal rates were slowed over 2 wt% of slurry contents in all types of slurries. The removal rates of alumina and fumed silica slurries were increased by phosphoric acid but acidic colloidal slurry was slightly increased at 2 vol% and soon decreased. The excessive addition of phosphoric acid affected the particle size distributions and increased scratches. Polishing pressure increased not only the removal rate but also the surface scratches. Acidic colloidal silica slurry showed the highest removal rate and the lowest roughness values among the 4 different slurry types.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.4007-4012
• /
• 2014

This study examined the fabrication and thermal properties of fumed silica/ceramic wool inorganic composites. A predetermined quantity of fumed silica and ceramic wool was mixed uniformly into a slurry state and stabilized in the mold at room temperature, and converted to a massive foamed body through a complete drying process at $150^{\circ}C$. Although the samples without polyvinyl alcohol (PVA) as an interfacial adhesive showed a bulk density of 0.6-0.8 $g/cm^3$ in the range, 10-70wt% fumed silica, those samples with 3wt% PVA exhibited remarkably lower bulk densities with enhanced mechanical and thermal insulation properties, without thermal cracking even above $800^{\circ}C$. The K-factor of the samples was lower in proportion to the fumed silica contents, showing good thermal insulation properties of ca. 0.08 $W/m^{\circ}K$ at $500^{\circ}C$ for the sample with 30wt% fumed silica.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.443-448
• /
• 1999

Tests have been carried out on four concrete containing different levels of silica fume to measure their permeability coefficient using water and oxygen, chloride ion. The total cementitious content was 351kg/㎥, and the water/cementitious materials ratio was 0.55. The results show that a dramatic reduction in permeability of concrete containing silica fume occurs due to formation of a discontinuous macro-pore system which inhibits flow. Porosity estimates from mercury-intrusion porosimetry are used to develop an explanations for the water and air permeability reduction. And, results of the rapid permeability test showed that the resistance of concrete to the penetration of chloride ions increases significantly as a contents of silica-fume is increased. The current intensity passing through the concrete containing silica fume is presented from 664C to 2166C.

• The Korean Journal of Ceramics
• /
• v.6 no.1
• /
• pp.37-42
• /
• 2000

To reduce shrinkage and the possibility of fracture during ambient pressure drying, it is of great importance to increase the strength and stiffness of the wet gels. In this paper is presented the strengthening and stiffening of wet silica gels prepared from sodium silicate (water glass) as well as properties of the corresponding xerogels. By washing gels containing different initial silica contents in water solutions at elevated pH, a maximum in shear modulus of ~4 MPa was obtained. The maximum stiffness enabled xerogels with bulk density of 0.28g/$\textrm{cm}^3$ to be made regardless of silica content and washing conditions. However, by aging the wet gels in a solution providing fresh monomers to the gel network, a shear modulus of 20 MPa was obtained after 27h. By this method monolithic xerogels with a density down to ~0.2g/$\textrm{cm}^3$ was prepared. The results are compared to alkoxide based gels.