• Elastomers and Composites
• /
• 제36권1호
• /
• pp.37-43
• /
• 2001

실리카와 카본블랙으로 보강된 SBR 배합물의 가황 특성과 bound rubber 함량 그리고 가황물의 물성에 보강제의 조성비가 미치는 영향을 연구하였다. 고무 배합물의 보강제 총 함량은 80.0 phr 이다. Bound rubber 함량은 실리카 함랑비가 증가할수록 증가하였고 점도 역시 증가하였는데, 특히 실리카 함량이 60.0 phr 이상일 때는 점도의 증가폭이 두드러지게 높아졌다. 가황시간은 실리카 함량이 증가할수록 느려졌고 가황 속도도 느려졌다. 실리카 함량비가 증가할수록 델타 토크가 증가함에도 불구하고 모둘러스는 감소하는 경향을 보였다. $60^{\circ}C$에서의 tan ${\delta}$ 값은 실리카 함량이 증가할수록 감소하였다.

• Macromolecular Research
• /
• 제16권4호
• /
• pp.329-336
• /
• 2008

Core/shell ($\pm$)PS/(-)silica nanocomposite particles were synthesized by dispersion polymerization using an amphoteric initiator, 2,2'-azobis [N-(2-carboxyethyl)-2,2-methylpropionamidine] ($HOOC(CH_2)_2HN$(HN=) $C(CH_3)_2CN$=NC $(CH_3)_2C$(=NH)NH $(CH_2)_2COOH$), VA-057. Negatively charged (-6.9 mV) silica was used as the stabilizer. The effects of silica addition time and silica and initiator concentrations were investigated in terms of polymerization kinetics, ultimate particle morphology, and size/size distribution. Uniform hybrid microspheres with a well-defined, core-shell structure were obtained at the following conditions: silica content = 10-15 wt% to styrene, VA-057 content=above 2 wt% to styrene and silica addition time=0 min after initiation. The delay in silica addition time retarded the polymerization kinetics and broadened the particle size distribution. The rate of polymerization was strongly affected by the silica content: it increased up to 15 wt% silica but then decreased with further increase in silica content. However, the particle size was only marginally influenced by the silica content. The zeta potential of the composite particles slightly decreased with increasing silica content. With increasing VA-057 concentration, the PS microspheres were entirely coated with silica sol above 1.0 wt% initiator.

• Elastomers and Composites
• /
• 제54권1호
• /
• pp.40-53
• /
• 2019

The physical properties of chloroprene rubber (CR) compounds reinforced with networked silicas were investigated by comparing them to those reinforced with conventional silica to observe the effect of the organic connection bonds combining silica particles on their cure, tensile, and aging performance. The introduction of networked silica to CR increase in silica content to 80 phr in rubber, while the content of conventional silica was limited to 60 phr. The CR compounds reinforced with networked silica showed higher resistance to combustion. The gradual increases in delta torque, Mooney viscosity, and modulus of silica-filled CR compounds with silica content were mainly attributed to the specific interaction between the chlorine atoms of CR and the hydroxyl groups of silica. The CR compounds reinforced with networked silica showed low compression set and heat build-up and maintained their high modulus even after thermal, oil, and ozone aging.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.1029-1034
• /
• 2001

The effects of binder content and silica sand content on the freezing and thawing resistance of lightweight polymer concrete are examined. As a result, the mass loss and pulse velocity of lightweight polymer concrete decrease with increasing binder content and silica sand content. The relative dynamic modulus and durability factor of lightweight polymer concrete reaches minimum at a silica sand content of 50% and a binder content of 28%, and is inclined to increase with increasing binder content and silica sand content.

• Macromolecular Research
• /
• 제8권6호
• /
• pp.285-291
• /
• 2000

Influence of silane coupling agent, bis-(3-(triethoxisilyl)-propyl)-tetrassulfide, on cure characteristics and bound rubber content of filled styrene-butadiene rubber (SBR) compounds and on physical properties of the vulcanizates was studied. Carbon black-filled and silica-filled compounds were compared. Content of the bound rubber increased with increased content of the silane coupling agent and this trend was shown more clearly in the silica-filled compounds. Optimum cure time of the carbon black-filled compound increased with increase of the silane content, while that of the silica-filled one decreased. Cure rate of the carbon black-filled compound became slower as the silane content increased while that of the silica-filled one became faster. By increasing the silane content, the minimum torque decreased and the delta torque increased. Physical properties of the silica-filled vulcanizate were found to be improved by adding the silane coupling agent. However, for the carbon black-filled vulcanizates, the tensile strength and tear resistance decreased with increase of the silane content. The differences between the carbon black-filled and silica-filled compounds were explained by difference in the reactivities of the fillers with the silane.

• Transactions on Electrical and Electronic Materials
• /
• 제13권6호
• /
• pp.322-325
• /
• 2012

Crystalline silica was synthesized by annealing amorphous silica at $1,300^{\circ}C$ or $1,400^{\circ}C$ for various times, and the crystallinity was estimated by X-ray diffraction (XRD) analysis. In order to prepare a low dielectric material, epoxy/crystalline silica composites were prepared, and the effect of silica content on the dielectric properties was studied under various functions of frequency and ambient temperature. The dielectric constant decreased with increasing crystalline silica content in the epoxy composites, and it also decreased with increasing frequency. At 120 Hz, the value of 5 wt% silica decreased by 0.25 compared to that of 40 wt% silica, and at 23 kHz, the value of 5 wt% silica decreased by 0.23 compared to that of 40 wt% silica. The value increased with increasing ambient temperature.

• International Journal of Concrete Structures and Materials
• /
• 제10권2호
• /
• pp.249-256
• /
• 2016

This paper deals with the effects of silica fume content and polymer-binder ratio on the properties of ultrarapid-hardening polymer-modified mortar using silica fume and ethylene-vinyl acetate redispersible polymer powder instead of styrene-butadiene rubber latex to shorten the hardening time. The ultrarapid-hardening polymer-modified mortar was prepared with various silica fume contents and polymer-binder ratios, and tested flexural strength, compressive strength, water absorption, carbonation depth and chloride ion penetration depth. As results, the flexural, compressive and adhesion strengths of the ultrarapid-hardening polymer-modified mortar tended to increase as increasing polymer-binder ratio, and reached the maximums at 4 % of silica fume content. The water absorption, carbonation and chloride ion penetration resistance were improved according to silica fume content and polymer-binder ratio.

• Elastomers and Composites
• /
• 제52권1호
• /
• pp.17-21
• /
• 2017

The optimum mixing conditions of silica and silane containing rubber composites were evaluated by investigating the properties of rubber composites prepared with a silica composition of 10, 20, 40, 60, and 80 g, respectively. The crosslinking rate decreased with increasing silica content, with he promoters being adsorbed on the silica surface with in the rubber composite. As a result, the increase in crosslinking time resulted in the destruction of the silica structure. The increase of the bound rubber content due to the destruction of the silica structure inhibited the chain motion of the polymer molecules and reduced the cohesion of the silica itself. Finally, the increase of silica content showed the increase of hardness, tensile strength, and storage modulus of rubber composites.

• Elastomers and Composites
• /
• 제53권3호
• /
• pp.109-123
• /
• 2018

The effect of the silica content on the state and properties of silica-filled styrene-butadiene rubber/butadiene rubber (SBR/BR) compounds containing coupling and dispersion agents was evaluated by varying the content of silica from 50 to 120 phr. Bis-[(triethoxysilyl)propyl] tetrasulfide (TESPT) and zinc 2-ethylhexanoate (ZEH) were used as the coupling and dispersion agents, respectively. The maximum silica content in the pristine material was 80 phr, which increased to 120 phr upon the addition of TESPT and ZEH. The incorporation of TESPT considerably improved most of the rubber properties due to its coupling action and the suppression of silica flocculation, while further addition of ZEH resulted in additional improvements. The properties of the rubber compounds with different silica contents can be fully explained either by an enhancement of the rubber-silica interactions or by their deterioration due to an excessive amount of silica aggregates.

• 콘크리트학회논문집
• /
• 제25권3호
• /
• pp.305-312
• /
• 2013

이 연구는 물-결합재(W/B) 비에 따른 실리카 퓸이 알칼리 활성화 슬래그 시멘트(AASC)에 미치는 유동성과 강도 특성에 대한 연구이다. W/B비는 0.50에서 0.60까지 0.05 단위로 일정하게 변화시켰다. 실리카 퓸은 고로슬래그 중량의 0%에서 50%까지 치환시켰다. 활성화제는 수산화나트륨(NaOH)를 사용하였고, 농도는 3M로 하였다. W/B 비에 따른 강도는 1, 3, 7 그리고 28일을 측정하였다. 유동성 측정 결과는 실리카 퓸의 치환율이 증가할수록 감소하였다. 압축강도는 실리카 퓸의 치환율이 증가할수록 증가하였다. 또한 W/B 비가 증가할수록 모든 재령에서 강도는 감소하였다. 실리카 퓸은 W/B 비와 실리카 퓸의 치환율에 따라서 활성화 반응을 증대시켜 강도를 증가시키는 것을 알 수 있었다.