• 전기의세계
• /
• 제21권2호
• /
• pp.9-19
• /
• 1972

The transient characteristics of separately excited d-c motor driven by thyristor d-c chopper is studied in this paper. The armature controlled system is applied. As a result of theoretrical analysis the following conculsions were drawn: (1) For the transient analysis, it is recognized that the state transition analysis is a more general method and powerful tool than the state equation method or signal flow graph method, although it includes iterative matrix calculations. And the system is dealt with a finite width sampled-data system in the state transition analysis. (2) The transient characteristics of the motor angular velocity and its torque to the sampling duration variation are compared with those due to the amplitude variation of d-c chopper voltage as follows. The attenuation rate of the transient characteristics is equal in both cases, but the initial value of the transient characteristics in former case is greater than in latter case. (3) The roots of characteristics equation of the system lie inside the unit circle of the Z-plane. Therefor the system is stable. Further it is found that as the sampling duration is decreased the relative stability is lessened.

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.663-670
• /
• 1998

Most of feedback shift controllers developed in the past have fixed control parameters tuned by experts using a trial and error method. Therefore, those controllers cannot satisfy the best control performance under various driving conditions. To improve the shift quality under various driving conditions, a new self-organizing controller(SOC) that has an optimal control performance through self-learning of driving conditions and driver's pattern is designed in this study. The proposed SOC algorithm for the shift controller uses simple descent method and has less calculation time than complex fuzzy relation, thus makes real-time control passible. PCSV (Pressure Control Solenoid Valve) control current is used as a control input, and turbine speed of the torque converter is used indirectly to monitor the transient torque as a feedback signal, which is more convenient to use and economic than the torque signal measured directoly by a torque sensor. The results of computer simulations show that an apparent reduction of shift-transient torque is obtained through the process of each run without initial fuzzy rules and a good control performance in the shift-transient torque is also obtained.

• 한국통신학회논문지
• /
• 제34권2C호
• /
• pp.181-185
• /
• 2009

프레임 단위로 식별 데이터베이스에 저장된 참조 신호의 특징 벡터와 유사성을 비교하여 입력 신호를 식별하는 경우에, 참조 신호의 특징 벡터로 데이터베이스를 어떻게 구성하는가에 따라 식별 성능은 영향을 받을 수 있다. 즉, 식별 데이터베이스의 구성 방법에 따라 데이터베이스의 크기와 식별을 위한 계산량, 식별 성능 등이 결정되며, 이것은 실제로 수중 천이신호 식별 시스템을 구성할 때 중요한 문제이다. 본 논문에서는 LBG 벡터 양자화 기법을 이용하여 식별 데이터베이스의 크기를 줄여 줌으로써 프레임 기반 수중 천이신호 식별 기법의 효율성을 증가시킬 수 있는 방법을 제안하고, 실험을 통하여 제안한 방법의 타당성을 검증하였다.

• 대한기계학회논문집
• /
• 제17권8호
• /
• pp.1910-1920
• /
• 1993

An experimental study to investigate the unconventional chip formation called triangulation of chip in cutting with a SPRT (self-propelled rotary tool) is performed using acoustic emission (AE) signal analysis. In doing that, a quantitative model of the AE RMS signal in triangulation with a SPRT is first developed. The predicted results from this model show good correlation between the AE RMS signal and the general characteristics of triangular chip formation. Then, effects of various process parameters such as cutting conditions (cutting speed, depth of cut, oblique angle and normal rake angle) and the work material properties on the chip formation in cutting with a SPRT are explored. Special attention is paid to the work material properties which are found to have significant effects on triangulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.173-176
• /
• 1996

The transient behavior of the complex-LMS adaptive filter is studied when the adaptive filter is operating on a fixed or sweeping complex frequency sine-wave signal. The first-order difference equation is derived for the mean weights and its closed form solution is obtained. The transient response is represented as a function of the eigenvectors and eigenvalues of input correlation matrix. The mean-square error of the algorithm is evaluated as well. An optimal convergence parameter and filter length can be determined for sweeping frequency sine-wave signals as a function of frequency change rate and signal and noise powers.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1759-1766
• /
• 2001

Vibration transient generated by developing localized fault in gear can be used as indicators in gear fault detection. In this paper, we propose the zoomed phase map for a fault signal using continuous wavelet transfers to detect this vibration transient. Local fault induces the abrupt fluctuation of load exciting tooth and phase lag in the vibration signal measured on the gearbox. The relatively large fault like "tip breakage" easily can be detected by the clear fluctuation of exciting load. However, minor fault like "initial pitting"cannot be detected using the load fluctuation. To defect this kind of minor fault, the phase map for a fault signal is taken into account. The phase lag by minor fault is observed well in the zoomed phase map.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.590-595
• /
• 2001

Vibration transient generated by developing localized fault in gear can be used as indicators of condition monitoring in a gear. In this paper, we propose the phase map for a fault signal using continuous wavelet transform to detect this vibration transient. Local fault induces the abrupt fluctuation of load exciting tooth and phase lag in the vibration signal measured on the gearbox. The relatively large fault like "tip breakage" easily can be detected by the clear fluctuation of exciting load. However, minor fault like "initial pitting" cannot be detected using the load fluctuation. To detect this kind of minor fault, the phase map for a fault signal is taken into account. The phase lag by minor fault is observed well in the phase map.

• 대한전자공학회논문지SD
• /
• 제43권12호
• /
• pp.89-101
• /
• 2006

다중 배선의 주파수 변화에 따른 전송전 파라미터를 계산하고 이를 이용하여 다증 배선의 주파수 종속 신호 천이 특성을 조사한다. 제시한 방법으로 다중 배선 입력신호의 스위칭 패턴, 상승 / 하강시간 (tr, tf) 및 길이에 따른 신호의 흔들림 (오버슛, 언더슛)과 크로스톡에 고주파 효과를 반영하여 시그널 인테그러티를 정확하게 결정할 수 있다. 고속 디지털 회에서 주파수 종속 특성을 고려하지 않으면 최악의 신호 동작 환경에서 글로벌 배선의 경우 26%와 260%, 패키지 배선은 11%와 70% 정도의 신호 천이와 크로스톡 노이즈 오차를 갖을 수 있다는 것을 보인다.

• 한국전자파학회논문지
• /
• 제27권3호
• /
• pp.291-298
• /
• 2016

본 논문에서는 전자파적합성 국제 규격인 IEC 61000-4-4에서 규정하고 있는 전기적으로 빠른 과도현상/버스트(EFT/Burst) 신호가 전원선을 따라 시험대상품에 인가될 때, 인가신호에 기인하여 방사되는 불요전자파와 그 신호가 피시험품에 미치는 영향에 대해 연구하였다. 먼저 국제규격에 규정된 시험 배치방법에 따라 시험 샘플을 설치하고, 검증된 EFT/Burst 발생기로 1분 동안 +4 kV의 규정된 신호를 길이 1 m인 전원선을 통해 시험 샘플에 인가하였다. 그 결과, 전원선을 통해 인가되는 전도성 EFT/Burst 내성 신호 외 버스트 발생기 및 전원선에서 직접 공기 중으로 방출되는 방사성 신호(EFT/Burst 노이즈)가 검출되었고, 국제 공인시험 규격으로 이 신호를 측정한 결과, 규제 레벨보다 30 dB 이상 높았다. 또한, EFT/Burst 방사성 신호의 최대 방사 지점과 시험품의 이격 거리에 따른 전계강도를 측정한 결과, 방사내성 국제 규격치보다 최대 23 V/m 이상 강한 전계강도가 검출되었다. 이는 EFT/Burst 방사성 노이즈가 직접적으로 제품에 인가되어 오동작을 유발할 가능성이 대단히 높으므로 대책이 요구됨을 확인하였다.

• Journal of Electrical Engineering and Technology
• /
• 제7권5호
• /
• pp.672-680
• /
• 2012

This paper proposes the control strategy of the shunt Flexible AC Transmission System (FACTS) devices to improve transient stability in multimachine power system. The multimachine power system has high nonlinear response after severe disturbance. The concept of Lyapunov energy function is applied to derive nonlinear control strategy and it was found that the time derivative of line voltage is not only can apply to control the shunt FACTS devices in multimachine system but also is locally measurable signal. The fuzzy logic control is also applied to overcome the uncertainty of various disturbances in multimachine power system. This paper presents the method of investigating the effect of the shunt FACTS devices on transient stability improvement. The proposed control strategy and the method of simulation are tested on the new England power system. It was found that the shunt FACTS devices based on the proposed nonlinear control strategy can improve transient stability of multimachine power system.