• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.150-156
• /
• 2001

This paper describes an implementation of the DSP(Digital Signal Processor) based triangular carrier frequency modulated RPWM inverter drive system. The power spectrum of the noise emitted from the induction motor was measured in the anechoic chamber. The analysis of the sources for the acoustic noise and the effects of the noise reduction are confirmed by the measured spectra of the noise. Real-time RPWM along with the speed control was achieved by high speed DSP. By changing the center frequency and the bandwidth of the carrier, the proposed real-time RPWM scheme can be used as an efficient switching frequency band acoustic noise reduction method for the inverter drive system with variant load conditions.

• Transactions of the Society of Information Storage Systems
• /
• v.7 no.1
• /
• pp.1-6
• /
• 2011

A control method for the angle servo of reference beam during reading recoded data images of a holographic data storage system is presented. The recording scheme with angle offset is adopted in order to verify the proposed angle servo. Using this recording scheme, the angle error signal is generated and we can implement the angle servo. Experiments have been performed on recording and reading data images to compensate Bragg angle mismatch.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.436-442
• /
• 2015

In this paper, we develop an indoor localization device which embeds localization information into indoor light-emitting-diodes (LED) lighting systems. The key idea of our device is the use of the newly proposed "bit stuffing method". Through the use of stuff bits, our device is able to measure signal strengths even in transient states, which prohibits interference between lighting signals. The stuff bits also scatter the parts of the signal where the LED is turned on, thus provides quality indoor lighting. Additionally, for the indoor localization system based on RSSI and TDM to be practical, we propose methods for the control of LED lamps and compensation of received signals. The effectiveness of the proposed scheme is validated through experiments with a low-cost implementation including an indoor navigation task.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.1E
• /
• pp.16-20
• /
• 2005

A novel scheme to measure the speaker information in speech signal is proposed. We develope the theory of quantitative measurement of the speaker characteristics in the information theoretic point of view, and connect it to the classification error rate. Homomorphic analysis based features, such as mel frequency cepstral coefficient (MFCC), linear prediction cepstral coefficient (LPCC), and linear frequency cepstral coefficient (LFCC) are studied to measure speaker specific information contained in those feature sets by computing mutual information. Theories and experimental results provide us quantitative measure of speaker information in speech signal.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.5 no.1
• /
• pp.1-6
• /
• 2005

In this paper, we propose an emotion recognition method using the facial images and speech signals. Six basic emotions including happiness, sadness, anger, surprise, fear and dislike are investigated. Facia] expression recognition is performed by using the multi-resolution analysis based on the discrete wavelet. Here, we obtain the feature vectors through the ICA(Independent Component Analysis). On the other hand, the emotion recognition from the speech signal method has a structure of performing the recognition algorithm independently for each wavelet subband and the final recognition is obtained from the multi-decision making scheme. After merging the facial and speech emotion recognition results, we obtained better performance than previous ones.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.837-838
• /
• 2006

This paper proposes a method of assembling parts using visual servoing in dynamic environment. We use SSD(Sum of Square Difference) based on adaptive template in order to detect a moving object in the case where the robot and the object both move. And the control input of the robot is obtained from the feed-back signal of the feature movement and the feed-forward signal of the camera movement in image plane.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.12
• /
• pp.4819-4834
• /
• 2015

The spectral efficiency of cellular networks can be improved when proximate users engage in device-to-device (D2D) communications to communicate directly without going through a base station. However, D2D communications that are not properly designed may generate interference with existing cellular networks. In this paper, we study resource allocation and power control to minimize the probability of an outage and maximize the overall network throughput. We investigate three power control-based schemes: the Partial Co-channel based Overlap Resource Power Control (PC.OVER), Fractional Frequency Reuse based Overlap Resource Power Control (FFR.OVER) and Fractional Frequency Reuse based Adaptive Power Control (FFR.APC) and also compare their performance. In PC.OVER, a certain portion of the total bandwidth is dedicated to the D2D. The FFR.OVER and FFR.APC schemes combine the FFR techniques and the power control mechanism. In FFR, the entire frequency band is partitioned into two parts, including a central and edge sub-bands. Macrocell users (mUEs) transmit using uniform power in the inner and outer regions of the cell, and in all three schemes, the D2D receivers (D2DRs) transmit with low power when more than one D2DRs share a resource block (RB) with the macrocells. For PC.OVER and FFR.OVER, the power of the D2DRs is reduced to its minimum, and for the FFR.APC scheme, the transmission power of the D2DRs is iteratively adjusted to satisfy the signal to interference ratio (SIR) threshold. The three schemes exhibit a significant improvement in the overall system capacity as well as in the probability of a user outage when compared to a conventional scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.480-480
• /
• 2000

In this paper, we proposed a fuzzy-neuro controller to control the speed of wound rotor induction motor with slip energy recovery. The speed is limited at some range of sub-synchronous speed of the rotating magnetic field. Control speed by adjusting resistance value in the rotor circuit that occurs the efficiency of power are reduced, because of the slip energy is lost when it passes through the rotor resistance. The control system is designed to maintain efficiency of motor. Recently, the emergence of artificial neural networks has made it conductive to integrate fuzzy controllers and neural models for the development of fuzzy control systems, Fuzzy-neuro controller has been designed by integrating two neural network models with a basic fuzzy logic controller. Using the back propagation algorithm, the first neural network is trained as a plant emulator and the second neural network is used as a compensator for the basic fuzzy controller to improve its performance on-line. The function of the neural network plant emulator is to provide the correct error signal at the output of the neural fuzzy compensator without the need for any mathematical modeling of the plant. The difficulty of fine-tuning the scale factors and formulating the correct control rules in a basic fuzzy controller may be reduced using the proposed scheme. The scheme is applied to the control speed of a wound rotor induction motor process. The control system is designed to maintain efficiency of motor and compensate power factor of system. That is: the proposed controller gives the controlled system by keeping the speed constant and the good transient response without overshoot can be obtained.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.12
• /
• pp.996-1001
• /
• 2005

Recently, with the development of service robots and with the new concept of ubiquitous world, the position estimation of mobile objects has been raised to an important problem. As pre-liminary research results, some of the localization schemes are introduced, which provide the relative location of the moving objects subjected to accumulated errors. To implement a real time localization system, a new absolute position estimation method for a mobile robot in indoor environment is proposed in this paper. Design and implementation of the localization system comes from the usage of active beacon systems (based upon RFID technology). The active beacon system is composed of an RFID receiver and an ultra-sonic transmitter: 1. The RFID receiver gets the synchronization signal from the mobile robot and 2. The ultra-sonic transmitter sends out the traveling signal to be used for measuring the distance. Position of a mobile robot in a three dimensional space can be calculated basically from the distance information from. Three beacons and the absolute position information of the beacons themselves. In some case, the mobile robot can get the ultrasonic signals from only one or two beacons, because of the obstacles located along the moving path. Therefore, in this paper, as one of our dedicated contribution, the position estimation scheme with less than three sensors has been developed. Also, the extended Kalman filter algorithm is applied for the improvement of position estimation accuracy of the mobile robot.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.10
• /
• pp.3439-3457
• /
• 2014

Clustering is an effective method for improving the performance of large scale mobile ad hoc networks. However, when the moving speed is very fast, the topology changes quickly, which leads to frequent cluster topology updates. The drastically increasing control overheads severely threaten the throughput of the network. SCBCS (Signal Characteristic Based Cluster Scheme) is proposed as a method to potentially reduce the control overheads caused by cluster formation and maintenance in aeronautical ad hoc networks. Each node periodically broadcasts Hello packets. The Hello packets can be replaced by data packets, which preserve bandwidth. The characteristics of the received packets, such as the Doppler shift and the power of two successive Hello packets, help to calculate the relative speed and direction of motion. Then, the link connection lifetime is estimated by the relative speed and direction of motion. In the clustering formation procedure, the node with the longest estimated link connection time to its one-hop neighbors is chosen as the cluster head. In the cluster maintenance procedure, re-affiliation and re-clustering schemes are designed to keep the clusters more stable. The re-clustering phenomenon is reduced by limiting the ripple effect. Simulations have shown that SCBCS prolongs the link connection lifetime and the cluster lifetime, which can reduce the topology update overheads in highly dynamic aeronautical ad hoc networks.