• Journal of computational fluids engineering
• /
• v.12 no.3
• /
• pp.41-46
• /
• 2007

Dynamic behavior of immiscible gas bubble attached to the wall in channel flow plays very important role in many engineering applications. Special attention has been paid to micro direct methanol fuel cell(${\mu}$DMFC) where surface tension becomes dominant factor with minor gravitational effect due to its reduced size. Therefore, displacement of $CO_2$ bubble generating on a cathode side in ${\mu}$DMFC can be very difficult and efficient removal of $CO_2$ bubbles will affect the overall machine performance considerably. We have focused our efforts on studying the dynamic behavior of immiscible bubble attached to the one side of the wall on 2D rectangular channel subject to external shear flow. We used Level Contour Reconstruction Method(LCRM) which is the simplified version of front tracking method to track the bubble interface motion. Effects of Reynolds number, Weber number, advancing/receding contact angle and property ratio on bubble detachment characteristic has been numerically identified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.152-158
• /
• 2004

An experimental study was performed to determine the fin-side heat transfer and pressure drop of a condenser for automobile. Five sample with different fin height and louver angle were tested, 9mm, 8mm, 7.5mm, 5.4mm and 4.5mm. Results are presented as plot of Colburn j-factor(or heat transfer coefficients) and friction factor(or pressure drop) against the Reynolds number(or inlet air velocity) based on louver pitch, in the range of 110 to 480. The results show that both heat transfer and pressure drop on the fin are mainly affected by the louver angle in a lower range of air velocity, but, by the fin height in a higher range of air velocity. The performance of 5.4mm fin is the highest, compared to other fin sample.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.685-690
• /
• 2000

In this study relationship between relief angles and chatter vibration in turning was examined by using the direct cutting test, in which the cutting depth of a tapered workpiece is varied continuously and the limiting depth of cut is measured at the time when chatter occurs. Test results reveal that 1) limiting depth of cut increases is proportion to side relief angles between 0$^{\circ}$ and 3$^{\circ}$, 2) limiting depth of cut does not show any evident change in spite of side relief angle increased from 3$^{\circ}$ to 12$^{\circ}$, 3) also limiting depth of cut does not change despite front angle change from 0$^{\circ}$ to 12$^{\circ}$.

• Journal of Welding and Joining
• /
• v.18 no.6
• /
• pp.74-82
• /
• 2000

The fluxless wetting properties of UBM-coated Si-wafer to the binary lead-free solders(Sn-Ag, Sn-Sb, Sjn-In, Sn0Bi) were estimated by wetting balance method. With the new wettability indices from the wetting curves of one side coated specimen, the wetting property estimation of UBM-coated Si-wafer was possible. For UBM of Si-chip, Au/Cu/Cr UBm was better than au/Ni/TI in the point of wetting time/ At general reflow process temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) was better than that of low melting point one(Sn-Bi, Sn-In). The contact angle of the one side coated Si-plate to the solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.

• The Journal of Internal Korean Medicine
• /
• v.35 no.4
• /
• pp.498-504
• /
• 2014

Objectives: This study investigated the change of foot rotation angle of gait analysis parameters according to gait improvement in post-stroke hemiplegic patients. Methods: We measured the foot rotation angle of eight post-stroke hemiplegic patients at the time of dependent and independent gait. Results: The foot rotation angle of the paralyzed side reduced closer to normal average according to gait improvement, but the non-paralyzed side not significantly. Conclusions: Improvement of foot rotation is an important thing for independent gait of post-stroke hemiplegic patients so this treatment seems worthy of being considered in clinical trials.

• Textile Coloration and Finishing
• /
• v.14 no.3
• /
• pp.19-25
• /
• 2002

Silk/cotton fabrics were treated with butanetetracarboxylic acid(BTCA) under various treating conditions such as concentration, treated time and curing temperatures. Bending property, tensile strength, wrinkle recovery angle, and shrinkage were measured. The BTCA concentration in the saponfication mixture was measured by an isocratic HPLC equipped with the strong cationic exchange column Aminex HPX-87-H and a UV detector. The detected concentration of BTCA was shown in silk side much more than that of cotton side. The bending and shrinkage properties were improved at minimum curing condition and the lower concentration of BTCA. Tensile strength decreased with increasing concentration of BTCA, curing temperature and treated time, while wrinkle recovery angle increased.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.876-880
• /
• 1997

In this paper we investigated the transcription of liquid crystal (LC) alignment method by using memory effect of nematic(N) LCon polymide(PI) surface with side chain as for non-rubbing alignment techniques. That the monodomain alignment of aligned NLC is observed by microscope textures in the cells on PI surface with side chain. We obtained that the pretilt angle of NLC are generated about 3.7$^{\circ}$on PI surface. We suggest that the LC alignment by using transcription alingnment method is attributed to memory effect of NLC on PI surface.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.195-201
• /
• 2005

In conventional Vehicle Stability Control (VSC) System, a control threshold is designed by average driver characteristics. Despite the stabilizing effort, VSC causes redundancy to an expert driver. An advanced VSC which has flexibility on its control property is proposed in this study. By using lateral velocity estimator, a control threshold is determined on side slip angle and angular velocity phase plane. Vehicle planar motion model based sliding controller is modified with respect to various control thresholds. The performance of the proposed VSC algorithm has been investigated by human-in-the-loop simulation using a vehicle simulator. The simulation results show that the control threshold has to be determined with respect to the driver steering characteristics. A VSC with variable control thresholds would provide an improvement compared to a VSC with a constant threshold.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.187-190
• /
• 2014

An experimental study on downwardly and upwardly spreading flames over slanted electrical wire, which is insulated by Polyethylene(PE), was conducted with applied AC electric field. The result showed that downwardly and upwardly spreading flames with angle of inclination leaned toward burnt side and unburned side, respectively. With applied AC electric fields, size of downwardly spreading flame decreased slightly and that of upwardly spreading flame increased significantly. Flame spread rate showed various trends in terms of inclination, applied voltage and frequency.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.2 s.7
• /
• pp.36-43
• /
• 2000

This study presents the centrifugal compressor performance for three different vane stagger angles and wall pressure distribution within vaned diffuser channels, and is also discussed about the stability with respect to the compressor components. As the vane stagger angle decreases, the flow rate for the stall onset decreases, and higher pressure can be obtained at the low flow rate region, however, the effective operation range of the compressor decreases because of the blockage effect of the diffuser vane. Low pressure pocket within the vaned diffuser channel moves from the pressure side of leading edge to the suction side as the flow rate decreases. The compressor system stability mainly depends on that of the diffuser.