• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.231-236
• /
• 1998

In general, the drying shrinkage of polymer-modified mortars using redispersible polymer powders is much higher than that of unmodified mortar. The purpose of this study is to reduce the drying shringkage of polymer-modified mortars using a redispersible poly(ethylene-vinyl acetate) (EVA) powder, which is widely used for the manufacture of prepackaged-type polymer-modified mortar products at present. Polymer-modified mortars using the redispersible EVA powder with powdered shrinkage-reducing agent were prepared with various polymer-cement ratios and shrinkage-reducing agent contents, and tested for drying shrinkage and strength. From the test results, the drying shrinkage of the redispersible EVA powder-modified mortars with a powdered shrinkage agent is remarkably reduced with increasing shrinkage-reducing agent content, and becomes approximately a half of that of the redispersible EVA powder-modified mortars with the same polymer-cement ratios and without the shrinkage-reducing agent at a shrinkage-reducing agent content of 6%.

• Advances in concrete construction
• /
• 제7권4호
• /
• pp.211-218
• /
• 2019

Predictions about shrinkage and creep of concrete are very important for evaluating time-dependent effects on structural performance. Some prediction models and formulas of concrete shrinkage and creep have been proposed with diversity. However, the influence of reinforcement ratio on shrinkage and creep of concrete has been ignored in most prediction models and formulas. In this paper, the concrete shrinkage and creep with different ratios of reinforcement were studied. Firstly, the shrinkage performance was tested by the 10 reinforced concrete beams specimens with different reinforcement ratios for 200 days. Meanwhile, the creep performance was tested by the 5 reinforced concrete beams specimens with different ratios of reinforcement under sustained load for 200 days. Then, the test results were compared with the prediction models and formulas of CEB-FIP 90, ACI 209, GL 2000 and JTG D 62-2004. At last, based on ACI 209, an improved prediction models and formulas of concrete shrinkage and creep considering reinforcement ratio was derived. The results from improved prediction models and formulas of concrete shrinkage and creep are in good agreement with the experimental results.

• 한국도로학회논문집
• /
• 제6권4호
• /
• pp.109-121
• /
• 2004

본 연구는 한국형 포장설계법 과제의 일환으로 수행된 콘크리트슬래브의 건조수축특성에 대한 연구로서 형상비 및 굵은 골재의 종류를 달리해 현재까지 252일간 수행된 실험결과이다. 실제 포장용 콘크리트 슬래브의 형상비에 접근하기 위한 방안으로 시편 일부 면의 수분 증발을 막기 위해 일부 면에 3중 코팅 처리와 랩 처리를 하였다. 예비실험결과 본 실험에서 채택한 수분방지 코팅 처리가 3달 정도까지는 신뢰성이 있음을 알 수 있었다. 동일한 형상비에서 사암을 사용한 콘크리트 시편의 건조수축이 석회암인 경우보다 형상비에 따라 1.32$\sim$1.80배 크게 측정되었다. 측정된 건조수축 변형률을 기존의 ACI와 CEB-FIP의 건조수축 모델식과 비교한 결과 두 식 모두 과소평가됨이 확인되었다. 최종적으로 재령 및 형상비 등을 고려한 다중 비선형 회귀분석을 통해 본 실험에 적합한 콘크리트시편의 건조수축 모델식을 제시하였다.

• 산업기술연구
• /
• 제22권A호
• /
• pp.193-200
• /
• 2002

Drying shrinkage cracking which may be caused by the relatively large specific surface IS a matter of grave concern for latex modified concrete(LMC) overlay and rapid-setting cement latex modified concrete(RSLMC) overlay. LMC and RSLMC were studied for field applications very actively in terms of strength and durability in Korea. However, there were no considerations in drying shrinkage. Therefore, the purpose of this dissertation was to study the drying shrinkage properties of LMC and RSLMC with the main experimental variables such as cement types(ordinary portland cement, rapid setting cement), water-cement ratios and curing days at a same controlled environment of 60% of relative humidity and $20^{\circ}C$ of temperature The drying shrinkage for specimens was measured with a digital dial gauge of Demec. The test results showed that the drying shrinkage of LMC and RSLMC were considerably lower with low water-cement ratio, respectively This might be attributed to the interlocking of hydrated cement and aggregates by a film of latex particles, water retention due to hydrophobic, and colloidal properties of the latexes resulting in reduced water evaporation.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.41-42
• /
• 2011

In this study, VA/E/MMA-modified mortars with nitrite-type hydrocalumite were prepared with various calumite contents and polymer binder-ratios, and tested for chloride ion penetration, carbonation and drying shrinkage. As a result, the chloride ion penetration and carbonation depths were somewhat increased with calumite contents, but those were remarkably decreased depending on the polymer-binder ratios. The 28-d drying shrinkage showed a tendency to increase with polymer-binder ratios and calumite contents. VA/E/MMA-Modified mortars with a calumite of 10 % were dissatisfied with KS requirements. Accordingly, a calumite content of 5 % for the VA/E/MMA-modified mortars with calumite is recommended.

• 한국염색가공학회지
• /
• 제12권2호
• /
• pp.103-110
• /
• 2000

To examine the physical properties of POY through the microstructure control, the crystal structure such as the crystallinity, the crystallite size, the orientation, the shrinkage, the tensile properties, and the thermal stress of POY(80/48, SD) were examined at different draw ratios and annealing temperatures. From the examination following conclusions were obtained : 1. The crystallinity was more effected by the heat setting temperature than by the draw ratio. The increasing rate was greatest at the heat setting temperature range of $170~190^\circ{C}$. 2. The crystallite size perpendicular to the fiber axis was more effected by the annealing temperature at lower draw ratios. On the other hand, the crystal and amorphous orientations were more effected by the heat setting at higher draw ratios. 3. The boiling shrinkage did not change significantly, but the total shrinkage showed 13% at the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$. 4. The maximum thermal stress increased with increasing the draw ratio and decreasing the heat setting temperature in the temperature range of $170~210^\circ{C}$. At the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$, the maximum thermal stress found was 1.1gf/d. 5. In the heat setting temperature above $170^\circ{C}$ after the drawing, the crystallinity, the crystallite size, the orientation, and the strength increased with increasing temperature, but the shrinkage and the maximum thermal stress decreased with increasing temperature.

• 한국도로학회논문집
• /
• 제14권1호
• /
• pp.45-53
• /
• 2012

본 연구에서는 다양한 포장용 콘크리트 배합의 건조수축 특성에 관한 실험결과를 분석하였다. 실험변수는 굵은골재의 종류(석회암, 사암, 화강암, 안산암, 편마암)와 잔골재의 종류(자연사, 부순모래) 및 콘크리트의 배합강도(보통강도, 고강도)를 달리하였다. 그리고 형상비가 22.2, 40, 85.7, 150, 200, 300을 갖도록 시편의 크기를 달리하였으며 코팅제(U&V-H(A,B))를 활용하였다. 다이얼게이지를 이용하여 항온($20^{\circ}C$) 항습(60%)에서 수행된 건조수축 실험은 길게는 1,014일 동안 측정하였다. KS에서 제시하는 표준시편에 비해 도로포장 모사용 슬래브 시편의 건조수축 변형률은 약 39% 감소되는 것으로 나타났다. 또한 동일한 형상비에 대해 굵은골재의 변화에 따른 건조수축 실험결과 석회암이 배합된 시편의 변형률이 사암대비 형상비별로 56~76% 범위에서 가장 낮게 측정되어 포장용 콘크리트로 사용되는데 유리할 것으로 판단된다.

• 대한치과보철학회지
• /
• 제37권6호
• /
• pp.800-808
• /
• 1999

To compare several porcelains made by various manufacturers in shrinkage after firing and investigate the effect of condensation on shrinkage, specimens were prepared and the volume of each body was measured by the phase-shifting profilometry. Baseplate wax was cut by $2.5cm{\times}2cm$ and cast in nonprecious metal(Verabond, U.S.A.), then any surfaces of specimens were abrased and polished on the SiC abrasing papers, preparing 120 specimens. Specimens were divided into six groups according to the porcelain used, and the porcelain used in each group were as follows. Group I : Ceramco dentin porcelain Group B : Creation dentin porcelain Group III : Creation margin porcelain Group IV : Vintage margin porcelain Group V : Vita dentin porcelain Group VI : Vintage dentin porcelain Porcelain was built up on the metal plates using a small spoon and then solution matching to each porcelain was added. The six groups are subdivided into a and b. In subgroup a, only excessive solution was absorbed with tissue and in subgroup b, porcelain was condensed sufficiently. When build-up was completed, the shape was measured using the phase-shifting profilometry. After that, specimens were fired in the furnace programed for each porcelain and then their changed shape were measured again. Using the difference between the two above measurements, the ratio of shrinkage was calculated. Obtained results were as follows ; 1. Regardless of condensation, the volume of fired specimens were not different significantly between the two subgroups a and b in the same group. 2. The ratios of shrinkage were significantly higher in the groups porcelain built-up was condensed than in the groups not condensed 3. The ratios of shrinkage were in the range of 36.81-27.19% in the groups porcelain built up was condensed and 44.52-37.54% in the other groups not condensed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.151-156
• /
• 2002

Drying shrinkage cracking which may be caused by the relatively large specific surface is a matter of grave concern for latex modified concrete(LMC) overlay and rapid-setting cement latex modified concrete(RSLMC) overlay. LMC and RSLMC were studied for field applications very actively in terms of strength and durability in Korea. However, there were no considerations in drying shrinkage. Therefore, the purpose of this study was to investigate the drying shrinkage properties of LMC and RSLMC with the main experimental variables such as cement types(ordinary portland cement, rapid setting cement), latex contents(0, 5, 10, 15, 20%), W-C ratios, and curing days at a controlled environment of 60% of relative humidity and 2$0^{\circ}C$ of temperature. The drying shrinkage for specimens was measured with a digital dial gauge of Demec. The test results showed that the drying shrinkage of LMC and RSLMC were considerably lower than that of OPC and RSC, respectively. This might be attributed to the interlocking of hydrated cement and aggregates by a film of latex particles, water retention due to hydrophobic, and colloidal properties of the latexes resulting in reduced water evaporation.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.166-167
• /
• 2015

The purpose of this study is to examine the effect on drying shrinkage of self-healing epoxy-modified mortars(EPMMs) using expansive admixtures. The EPMMs are prepared with polymer-binder ratios of 0 and 10%, and tested for drying shrinkage and pore structure analysis. As a result, regardless of the expansion and swelling agent content, the drying shrinkage of the EPMMs is remarkably decreased than that of unmodified mortars. Also, the pore size distribution of the EPMMs is moved to smaller size in comparison with unmodified mortars. In this study, the EPMM with expansive agent 7.5% and swelling agent 2.5% is recommended as a optimal mix proportion for reduction of drying shrinkage.