• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.47-52
• /
• 2000

Recently, it is very necessary the development of the manufacturing techniques for high strength concrete(HSC) for the large-scale size and good quality of civil structure. But, the manufacture and quality control of HSC of which shrinkage, heat of hydration and workability at construction filed are considered, is very difficult due to its low water-cement ratio and high quantity of unit cement content. In the present study, we tried to know and assess the influences of chemical and physical properties of cement on the material properties of HSC. We analyzed basic properties of 4 kinds of cement whose chemical and physical properties are different each other through various tests such as chemical analysis and mortal test. Also, we performed the assessment of the material properties of HSC for each dement by the test for the conditions of same mix design and similar compressive strength. From the results in the study, the assessment of the important quality factors of cement influencing the properties of HSC may be utilized to quality control of applied cement to manufacture the HSC of high quality.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.27-32
• /
• 1997

It was fond that the compressive and flexural strength of recycled concrete was decreased with increasing the content of recycled aggregate and the early compressive strength was also decreased with increasing Fly Ash level. In comparison with recycled concretes producing various sources, the trend were similar to those shown above, but the differences were minor. the development of Flexural strength in both concretes was similar, but the recycled concrete is lower in the ratio of flexural strength and compressive strength. The drying shrinkage of recycled concrete is increased with increasing the amount of recycled aggregate, particularly the maximum differences were reached between at 2 and 3 weeks.

• Journal of the Korea Concrete Institute
• /
• v.12 no.5
• /
• pp.153-164
• /
• 2000

Numerical studies were carried out to investigate long-term behavior of flat plates, subjected to combined in-plane compressive and transverse loads. For the numerical studies, a computer program of nonlinear finite element analysis was developed. It can address creep and shrinkage as weel as geometrical and material nonlinearity, and also it can address various load combinations and loading sequences of transverse load, in-plane compressive load and time. This numerical method was verified by comparison with the existing experiments. Parametric studies were performed to investigate the strength variations of flat plates with four parameters; 1) loading sequence of floor load, compressive load and time 2) uniaxial and biaxial compression 3) the ratio of dead to live load 4) span length. Through the numerical studies, the behavioral characteristics of the flat plates and the governing load combinations were examined. These results will be used to develop a design procedure for the long-term behavior of flat plates in the future.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.687-694
• /
• 2013

This study was performed with an aim to improve the early-age strength of concrete containing fly ash, which is known to increase the long-age strength of concrete, reduce drying shrinkage, and enhance water tightness. The composition was partially substituted with calcium sulfoaluminate (CSA), from which ettringite is actively produced, in the early stages of hydration to verify its effect on improving the early-age strength and to determine the optimal mixing ratio. For this purpose, up to 30 % of the cement weight was substituted with fly ash, and the amount of CSA substitution was 8% of the fly ash weight. The mixtures were then fabricated into concrete specimens for compressive strength measurement and analysis of the correlation between the hydration products and the compressive strength.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.129-133
• /
• 2008

As a rotating machine element, plastic gears are more and more widely used in such as industrial machine element, since plastic gear is lighter, higher wear-resistance, and higher vibration absorbing ability than metal gears. When operating plastic parts, tooth breakage and fatigue life shortened due to increasing number of applying load and tooth flank temperature rising, such that accuracy of plastic gears is divided from allowable range to cause vibration and noise. On this study, a internal plastic gears are developed which improved the filling balance molding process by a new injection mold structure. The new mold structure called HR3P(hot runner type 3plate mold). As the result from this studies, we obtained a very accurate roundness internal gears by using design of experiment.

• Design & Manufacturing
• /
• v.2 no.2
• /
• pp.33-37
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.111-115
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program $Moldflow^{TM}$ and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.291-293
• /
• 2005

The purpose of this study is to evaluate the effects of line heating variables for forming the curved plate on the behavior of distortion using FEA and experiment. The optimum mixed ratio and standoff for flame heating was established under the heating conditions given in this study. With the heating condition, the predictive equation of angular distortion and transverse shrinkage was established using FEA and verified by comparing the predicted results and experimental results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.17-23
• /
• 1996

The objective of this study is to present the reference data about the influence of concrete properties using crushed sand, according to the change of powder content and grain shape. From the test results. We obtained that as powder content is increased, sand aggregate ratio, water content and S.P/C are increased in mixing design of concrete. The more powder content is the less slump and air content loss are decreased in fresh state, but the higher compressive strength and drying shrinkage are increased in hardened concrete state. As grain shape become round, water content is decreased in mixing design of concrete. And also, loss of slump and air content in fresh state, compressive strength in hardened state are increased.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.46-47
• /
• 2015

This study has analyzed the engineering characteristics of resource-cycling mortar according to the variation of fine aggregate type using illite with high development potentials by setting the goal as developing eco-friendly construction materials. As a result, while flow has increased if recycled fine aggregate and waste refractory are used separately or mixing them adequately in case of flow and compressive strength, the flow had somewhat declined followed by illite replacement. However, the possibility of such usage is determined to be adequate if used by mixing illite, recycled fine aggregate and waste refractory properly due to the dry shrinkage effect.